IEC 61196-1-113:2009

Coaxial communication cables - Part 1-113: Electrical test methods - Test for attenuation constant

IEC 61196-1-113:2009(E) applies to coaxial communications cables. It specifies a test method for determining the attenuation constant of coaxial cables for use in communications systems. The test is applicable preferably at frequencies ≥ 5 MHz but also for lower frequencies if the magnitude of the complex characteristic impedance is approximately equal to the nominal characteristic impedance of the specimen or if a form fitting function is applied.

General Information

• Status: Published
• Publication Date: 11-Aug-2009
• ICS: 33.120.10 - Coaxial cables. Waveguides
• Technical Committee: SC 46A - Coaxial cables
• Drafting Committee: WG 3 - TC 46/SC 46A/WG 3
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 12-Jan-2018

Relations

• Revised: IEC 61196-1-113:2018 - Coaxial communication cables - Part 1-113: Electrical test methods - Test for attenuation constant
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 61196-1-113


®

Edition 1.0 2009-08



INTERNATIONAL



STANDARD





Coaxial communication cables –
Part 1-113: Electrical test methods – Test for attenuation constant



IEC 61196-1-113:2009(E)

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED

Copyright © 2009 IEC, Geneva, Switzerland



All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,

please contact the address below or your local IEC member National Committee for further information.



IEC Central Office
3, rue de Varembé

CH-1211 Geneva 20

Switzerland
Email: [e-mail]
Web: www.iec.ch

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]

---------------------- Page: 2 ----------------------
IEC 61196-1-113


®

Edition 1.0 2009-08



INTERNATIONAL



STANDARD





Coaxial communication cables –
Part 1-113: Electrical test methods – Test for attenuation constant



INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
H
ICS 33.120.10 ISBN 978-2-88910-440-6
® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 3 ----------------------
– 2 – 61196-1-113 © IEC:2009(E)


CONTENTS


FOREWORD.3

1 Scope.5


2 Normative references .5

3 Attenuation constant.5

4 Test method .5

4.1 Equipment.5

4.2 Test specimen.6

4.3 Procedure .6
5 Expression of test results .6
5.1 Expression .6
5.2 Temperature correction .7
6 Form fitting.7
7 Test report.8
8 Requirements .8

---------------------- Page: 4 ----------------------
61196-1-113 © IEC:2009(E) – 3 –


INTERNATIONAL ELECTROTECHNICAL COMMISSION

____________



COAXIAL COMMUNICATION CABLES –



Part 1-113: Electrical test methods –

Test for attenuation constant





FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent
...