Amendment 1 - Luminaires - Part 2-22: Particular requirements - Luminaires for emergency lighting

Amendement 1 - Luminaires - Partie 2-22: Règles particulières - Luminaires pour éclairage de secours

General Information

Status
Published
Publication Date
21-Sep-2017
Technical Committee
Current Stage
DELPUB - Deleted Publication
Completion Date
06-Dec-2021
Ref Project

Buy Standard

Standard
IEC 60598-2-22:2014/AMD1:2017 - Amendment 1 - Luminaires - Part 2-22: Particular requirements - Luminaires for emergency lighting
English and French language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

IEC 60598-2-22
Edition 4.0 2017-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Luminaires –
Part 2-22: Particular requirements – Luminaires for emergency lighting
Luminaires –
Partie 2-22: Règles particulières – Luminaires pour éclairage de secours
IEC 60598-2-22:2014-06/AMD1:2017-09(en-fr)
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2017 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from

either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC

copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or

your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite

ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie

et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des

questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez

les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC

The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes

International Standards for all electrical, electronic and related technologies.
About IEC publications

The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the

latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org

The stand-alone application for consulting the entire The world's leading online dictionary of electronic and

bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in

Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional

documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical

iPad. Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary

The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and

variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of

committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been

and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc

details all new publications released. Available online and If you wish to give us your feedback on this publication or

also once a month by email. need further assistance, please contact the Customer Service

Centre: csc@iec.ch.
A propos de l'IEC

La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des

Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC

Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la

plus récente, un corrigendum ou amendement peut avoir été publié.
Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org

Application autonome pour consulter tous les renseignements Le premier dictionnaire en ligne de termes électroniques et

bibliographiques sur les Normes internationales, électriques. Il contient 20 000 termes et définitions en anglais

Spécifications techniques, Rapports techniques et autres et en français, ainsi que les termes équivalents dans 16

documents de l'IEC. Disponible pour PC, Mac OS, tablettes langues additionnelles. Egalement appelé Vocabulaire

Android et iPad. Electrotechnique International (IEV) en ligne.

Recherche de publications IEC - www.iec.ch/searchpub Glossaire IEC - std.iec.ch/glossary

La recherche avancée permet de trouver des publications IEC 65 000 entrées terminologiques électrotechniques, en anglais

en utilisant différents critères (numéro de référence, texte, et en français, extraites des articles Termes et Définitions des

comité d’études,…). Elle donne aussi des informations sur les publications IEC parues depuis 2002. Plus certaines entrées

projets et les publications remplacées ou retirées. antérieures extraites des publications des CE 37, 77, 86 et

CISPR de l'IEC.
IEC Just Published - webstore.iec.ch/justpublished

Restez informé sur les nouvelles publications IEC. Just Service Clients - webstore.iec.ch/csc

Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur cette

Disponible en ligne et aussi une fois par mois par email. publication ou si vous avez des questions contactez-nous:

csc@iec.ch.
---------------------- Page: 2 ----------------------
IEC 60598-2-22
Edition 4.0 2017-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Luminaires –
Part 2-22: Particular requirements – Luminaires for emergency lighting
Luminaires –
Partie 2-22: Règles particulières – Luminaires pour éclairage de secours
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.140.40 ISBN 978-2-8322-4809-6

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 3 ----------------------
– 2 – IEC 60598-2-22:2014/AMD1:2017
© IEC 2017
FOREWORD

This amendment has been prepared by subcommittee 34D: Luminaires, of IEC technical

committee 34: Lamps and related equipment.
The text of this amendment is based on the following documents:
FDIS Report on voting
34D/1296/FDIS 34D/1304/RVD

Full information on the voting for the approval of this amendment can be found in the report

on voting indicated in the above table.

The committee has decided that the contents of this amendment and the base publication will

remain unchanged until the stability date indicated on the IEC website under

"http://webstore.iec.ch" in the data related to the specific publication. At this date, the

publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________
INTRODUCTION to Amendment 1

The light output of LED light sources depends also on the temperature at which it is operated.

Typically the temperature is controlled by a heat sink on which it is mounted (e.g. luminaire

surface).

For this reason, the calculation of the ratio of the electrical parameter (EOF ) will be

introduced in the LED controlgear standards IEC 61347-2-13 and IEC 61347-2-7, as the direct

measurement of EBLF is not practicable.

In particular EOF is defined as the ratio of the current in emergency mode from constant

current controlgear divided by the nominal current of LED (I ):
normal mode
EOF = I / I
I emergency normal mode

Knowing that the light output of an LED light source is nearly directly proportional with the

foreward current flowing through it, it is possible to calculate the luminous flux of the luminaire

in emergency mode by using the EOF or I from constant current controlgear
I emergency

This document contains a proposal for the modification of IEC 60598-2-22 to use the factor

EOF or I in the luminaire.
I emergency
___________

Any non-linearity due to the increased efficacy at lower operation temperature leads to an increased tolerance

of the light output in the emergency mode but always positive.
---------------------- Page: 4 ----------------------
IEC 60598-2-22:2014/AMD1:2017 – 3 –
© IEC 2017
22.2 Normative references
Delete the reference to IEC 60354-5-56
Add the following new reference:
CIE S025, Test Method for LED Lamps, LED Luminaires and LED Modules
22.3 Terms and definitions
22.3.23
Replace the existing note 1 to entry with the following new note 1 to entry:
Note 1 to entry: PELF = LDL × EBLF

where LDL is the rated luminous flux of fluorescent or discharge lamp, this is taken as the initial lighting design

lumens at 100 h.
Add, at the end of 22.3, the following new terminological entry:
22.3.28
practical emergency light source flux
PELSF

minimum luminous flux of the light source observed during the rated duration of the

emergency mode
Note 1 to entry: For LED light sources:
a) if EOF is given: PELSF = LDL x EOF
I I
b) if I from constant current controlgear is defined: PELSF = LDL x (I / I )
emergency emergency normal mode

where LDL is the lumen output of the LED module under the condition corresponding to the operation in the

luminaire (identical tp) operated at the same current (I ).
normal mode
Note 2 to entry: This note only applies to the French language.
22.7 Construction

In the first paragraph, replace the last two sentences with the following new text:

In addition, emergency luminaires with automatic testing systems shall comply with the

additional requirements of IEC 62034 as identified in Annex K of IEC 61347-2-7.
22.7.2

In the first paragraph, replace the text "… IEC 61347-2-7, IEC 61347-2-3: Annex J,

IEC 61347-2-2, IEC 61347-2-12 and IEC 61347-2-13 as appropriate" with the following new

text:

IEC 61347-2-2, IEC 61347-2-3: IEC 61347-2-7, IEC 61347-2-12 and IEC 61347-2-13 as

appropriate and with the additional safety requirements for electronic controlgear for

emergency lighting in the appropriate annex of the standards (e.g. Annex J of
IEC 61347-2-3).”
22.7.10
Delete the existing third paragraph and add the following new note:
NOTE Installation details can be found in IEC 60364-5-56.
---------------------- Page: 5 ----------------------
– 4 – IEC 60598-2-22:2014/AMD1:2017
© IEC 2017
22.17 Photometric data
22.17.1
Replace the existing text with the following new text:

The manufacturer shall make available the intensity distribution data necessary for the

calculation of the emergency lighting installation according to ISO 30061. The intensity data in

emergency mode may be provided in candelas or in relative cd/1 000 lm. If the values are

declared in candelas, the manufacturer shall provide the emergency luminaire rated luminous

flux derived from the intensity distribution table.

Compliance is checked by direct measurements in emergency operating condition taking into

account the test operating condition described in 22.17.3 or by measurements in normal

operating condition and calculation as described in 22.17.2.
22.17.2
Replace "Void" with the following new text:

If values are declared in cd/1 000 lm, the manufacturer shall also provide the reference flux in

emergency mode.

In the case of luminaires with tubular fluorescent lamps or other discharge lamps the

reference flux is the practical emergency light source flux PELF calculated as the rated flux of

the lamp multiplied by the EBLF of the associated emergency ballast.
In the case of luminaires with LED light source the reference flux is:
– the practical emergency light source flux PELSF

The value may be calculated as the light source luminous flux of the LED module (LDL) in

reference condition corresponding to the luminaire (at the same t ) and at rated current

(I ) multiplied by the EOF or (I / I ) of the associated constant
normal mode I emergency normal mode
current emergency controlgear

NOTE 1 In this case the LOR of the luminaire has influence on the calculation of the emergency rated luminaire

flux.
– the emergency luminaire rated luminous flux
This value shows the rated luminous flux of the luminaire in normal mode (I )
normal mode
multiplied by the EOF or (I / I ) of the associated constant current
I emergency normal mode
emergency controlgear.
NOTE 2 In this case the LOR of the luminaire is considered as 1.
The factor EOF can only be used under the following conditions:
– The forward current of the LED is controlled by the controlgear only.

– All LEDs mounted in the luminaire are supplied both in normal operating conditions and in

emergency mode.

– The luminaire luminous flux and/or the LED light source luminous flux is measured at

I corresponding to the I of the controlgear (e.g. in the case of a
normal mode normal mode
luminaire to be used with independent controlgear).
– The current in emergency mode is equal or lower than I (EOF equal or lower
normal mode I
than 1).

NOTE 3 The use of emergency output factors different from EOF (e.g. EOF or EOF ) are not part of the scope

I U P
of 22.17.2. They can only be used for design purposes and not for testing.
---------------------- Page: 6 ----------------------
IEC 60598-2-22:2014/AMD1:2017 – 5 –
© IEC 2017
22.17.3
Replace "Void" with the following new text:

Emergency luminaires shall provide at least 50 % of the level declared photometric data

claimed by the manufacturer during operation in emergency mode 5 s after failure of the

normal supply, and full rated photometric performance after 60 s and continuously to the end

of the rated duration of the emerge
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.