IEC 60745-1:2001/COR1:2003
(Corrigendum)Corrigendum 1 - Hand-held motor-operated electric tools - Safety - Part 1: General requirements
Corrigendum 1 - Hand-held motor-operated electric tools - Safety - Part 1: General requirements
IEC 60745-1-ed3, Corrigendum 1 - Hand-held motor-operated electric tools - Safety - Part 1: General Requirements.
General Information
Relations
Standards Content (Sample)
IEC 60745-1
(Third edition – 2001)
Hand-held motor-operated electric tools – Safety –
Part 1: General requirements
CORRIGENDUM 1
Pa ge 72
Figure 1 – Standard test finge
...
This May Also Interest You
IEC 62841-2-19:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held jointers. IEC 62841-1:2014, Clause 1 is applicable, except as follows: This document applies to hand-held jointers for cutting into wood or materials with similar physical characteristics such as, for example, chipboard, fibreboard and plywood.
- Standard210 pagesEnglish languagesale 15% off
- Standard38 pagesEnglish and French languagesale 15% off
IEC 62841-2-20:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held band saws. Where a particular subclause of IEC 62841-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1 is to be adapted accordingly.
IEC 62841-1:2014, Clause 1 is applicable, except as follows:
This document applies to hand-held band saws.
- Standard204 pagesEnglish languagesale 15% off
- Standard33 pagesEnglish and French languagesale 15% off
IEC 62841-2-16:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held fastener driving tools. Where a particular subclause of IEC 62841-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1 is to be adapted accordingly.
IEC 62841-1:2014, Clause 1 is applicable, except as follows:
Addition: This document applies to hand-held fastener driving tools
- intended for driving fasteners into or through concrete, fabric, fiberboard, metal, plastic, wood, wood products, cartons, and other materials; and
- whose energy to drive the fastener is derived directly or indirectly from an electric motor or magnetic drive.
This document does not apply to pneumatically driven tools where the compressed gas comes from an external source, such as a compressor or a tank.
This document does not apply to tools powered by combustible gases, even if electrically ignited.
NOTE 101 Tools powered by compressed air or combustible gases are covered by ISO 11148-13:2017.
- Standard249 pagesEnglish languagesale 15% off
- Standard73 pagesEnglish and French languagesale 15% off
IEC 62841-2-23:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held die grinders and small rotary tools. IEC 62841-1:2014, Clause 1 is applicable, except as follows:
This document applies to hand-held die grinders and to small rotary tools for mounted accessories not exceeding 55 mm in diameter and for mounted sanding accessories not exceeding 80 mm in diameter such as:
- threaded cones and plugs that are threaded on a mandrel with an unrelieved shoulder flange,
- mandrel mounted wheels, and
- rotary files
with a rated speed not exceeding a peripheral speed of the accessory of 80 m/s at rated capacity.
This document does not apply to straight and vertical grinders utilizing flanges for driving an abrasive accessory.
NOTE 101 Straight and vertical grinders are covered by IEC 62841-2-3.
- Standard233 pagesEnglish languagesale 15% off
- Standard54 pagesEnglish and French languagesale 15% off
IEC 62841-2-18:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held strapping tools. Where a particular subclause of IEC 62841-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1 is to be adapted accordingly. This document applies to hand-held strapping tools.
- Standard197 pagesEnglish languagesale 15% off
- Standard29 pagesEnglish and French languagesale 15% off
IEC 62841-3-3:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for transportable planers and thicknessers.
IEC 62841-1:2014, Clause 1 is applicable, except as follows:
This document applies to transportable planers, thicknessers and combined planers and thicknessers intended for cutting wood and analogous materials with a maximum planing width of 330 mm.
This document does not apply to planers, thicknessers or combined planers and thicknessers other than transportable.
NOTE 101 ISO 19085-7:2019 gives requirements for planers, thicknessers or combined planers and thicknessers other than transportable.
- Standard258 pagesEnglish languagesale 15% off
- Standard73 pagesEnglish and French languagesale 15% off
IEC 63241-2-1:2024 supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Electric motor-operated tools - Dust measurement procedure - Particular requirements for hand-held core drills.
Where a particular subclause of IEC 63241-1:2023 is not mentioned in this Part 2-1, that subclause applies as far as relevant. Where this standard states "addition", "modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.
- Standard13 pagesEnglish and French languagesale 15% off
IEC 62841-2-7:2024 deals with the safety of electric motor-operated hand-held spray guns for non-flammable materials. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-7 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
- Standard206 pagesEnglish languagesale 15% off
- Standard37 pagesEnglish and French languagesale 15% off
IEC 62841-2-12:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held concrete vibrators. IEC 62841-1:2014, Clause 1 is applicable, except as follows.
Addition: This document applies to hand-held concrete vibrators.
- Standard207 pagesEnglish languagesale 15% off
- Standard38 pagesEnglish and French languagesale 15% off
IEC 62841-3-4:2016 applies to transportable bench grinders that can be equipped with one or two accessories as follows:
- type 1 grinding wheels in accordance with ISO 603-4:1999 with a diameter not exceeding 310 mm and a thickness not exceeding 55 mm;
- wire brushes with a diameter not exceeding 310 mm and a thickness not exceeding 55 mm;
- polishing wheels with a diameter not exceeding 310 mm and with a peripheral speed of any accessory between 10 m/s and 50 m/s. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Keywords: Bench Grinder, Hand-held tool, Transportable tool
This publication is to be read in conjunction with IEC 62841-1:2014. The contents of the corrigendum of December 2016 have been included in this copy.
- Standard46 pagesEnglish and French languagesale 15% off
- Standard94 pagesEnglish and French languagesale 15% off
- Standard99 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.