IEC 60384-20:2008

Fixed capacitors for use in electronic equipment - Part 20: Sectional specification - Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors

Is applicable to fixed surface mount capacitors for direct current, with metallized electrodes and polyphenylene sulfide dielectric for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted directly onto substrates for hybrid circuits or onto printed boards. These capacitors may have "self healing properties" depending on conditions of use. They are primarily intended for applications where the a.c. component is small with respect to the rated voltage. The contents of the corrigendum of February 2008 have been included in this copy.

General Information

• Status: Published
• Publication Date: 21-Jan-2008
• ICS: 31.060.10 - Fixed capacitors
• Technical Committee: TC 40 - Capacitors and resistors for electronic equipment
• Drafting Committee: MT 60384-20 - TC 40/MT 60384-20
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 22-Jul-2015

Relations

• Corrected By: IEC 60384-20:2008/COR1:2008 - Corrigendum 1 - Fixed capacitors for use in electronic equipment - Part 20: Sectional specification - Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors
• Effective Date: 05-Sep-2023
• Revises: IEC 60384-20:1996 - Fixed capacitors for use in electronic equipment - Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric chip d.c. capacitors
• Effective Date: 05-Sep-2023
• Revised: IEC 60384-20:2015 - Fixed capacitors for use in electronic equipment - Part 20: Sectional specification - Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 60384-20
Edition 2.0 2008-01
INTERNATIONAL
STANDARD
QC 302000
Fixed capacitors for use in electronic equipment –
Part 20: Sectional specification – Fixed metallized polyphenylene sulfide film
dielectric surface mount d.c. capacitors

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
IEC 60384-20
Edition 2.0 2008-01
INTERNATIONAL
STANDARD
QC 302000
Fixed capacitors for use in electronic equipment –
Part 20: Sectional specification – Fixed metallized polyphenylene sulfide film
dielectric surface mount d.c. capacitors

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
T
ICS 31.060.10 ISBN 2-8318-9547-2

– 2 – 60384-20 © IEC:2008(E)
CONTENTS
FOREWORD.4

1 General .6
1.1 Scope.6
1.2 Object .6
1.3 Normative references .6
1.4 Information to be given in a detail specification .6
1.4.1 Outline drawing and dimensions .7
1.4.2 Mounting .7
1.4.3 Ratings and characteristics.7
1.4.4 Marking .7
1.5 Terms and definitions .8
1.6 Marking .8
2 Preferred ratings and characteristics .9
2.1 Preferred characteristics .9
2.1.1 Preferred climatic categories .9
2.2 Preferred values of ratings .9
2.2.1 Rated capacitance (C ) .9
R
2.2.2 Tolerance on rated capacitance.9
2.2.3 Rated voltage (U ) .10
R
2.2.4 Category voltage (U ) .10
C
2.2.5 Rated temperature.10
3 Quality assessment procedures.10
3.1 Primary stage of manufacture.10
3.2 Structurally similar components.10
3.3 Certified records of released lots.10
3.4 Qualification approval.10
3.4.1 Qualification approval on the basis of the fixed sample size
procedure .10
3.4.2 Tests .11
3.5 Quality conformance inspection.16
3.5.1 Formation of inspection lots.16
3.5.2 Test schedule .17
3.5.3 Delayed delivery.17
3.5.4 Assessment levels.17
4 Test and measurement procedures.18
4.1 Mounting .18
4.2 Visual examination and check of dimensions.18
4.2.1 Visual examination .18
4.2.2 Requirements .18
4.3 Electrical tests.18
4.3.1 Voltage proof.18
4.3.2 Capacitance .19
4.3.3 Tangent of loss angle (tan δ) .19
4.3.4 Insulation resistance.20
4.4 Adhesion .21

60384-20 © IEC:2008(E) – 3 –
4.5 Bond strength of the end of plating.21
4.5.1 Initial measurement .21
4.5.2 Final inspection .21
4.6 Resistance to soldering heat .21
4.6.1 Initial measurement .21
4.6.2 Test conditions .21
4.6.3 Final inspection, measurements and requirements .21
4.7 Solderability .22
4.7.1 Test conditions .22
4.7.2 Final inspection, measurements and requirements .22
4.8 Rapid change of temperature .22
4.8.1 Initial measurements .22
4.8.2 Number of cycles: 5.22
4.8.3 Intermediate inspection .22
4.9 Climatic sequence .22
4.9.1 Initial measurements .22
4.9.2 Dry heat .22
4.9.3 Damp heat, cyclic, test Db, first cycle .22
4.9.4 Cold .22
4.9.5 Damp heat, cyclic, test Db, remaining cycles .23
4.9.6 Final inspection, measurements and requirements .23
4.10 Damp heat, steady state.23
4.10.1 Initial measurements .23
4.10.2 Final inspection, measurements and requirements .23
4.11 Endurance.23
4.11.1 Initial measurements .23
4.12 Charge and discharge .24
4.12.1 Initial measurements .24
4.13 Component solvent resistance (if applicable).24
4.14 Solvent resistance of the marking (if applicable).24

Table 1 – Fixed sample size test plan for qualification approval – Assessment level EZ.12
Table 2 – Test schedule for qualification approval.13
Table 3 – Lot-by-lot inspection .17
Table 4 – Periodic tests .18
Table 5 – Test voltages.19
Table 6 – Tangent of loss angle limits.20
Table 7 – Requirements insulation resistance .20
Table 8 – Correction factor dependent on test temperature.21
Table 9 – Endurance test Grade 1, Grade 2 and Grade 3 capacitors.23

– 4 – 60384-20 © IEC:2008(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 20: Sectional specification –
Fixed metallized polyphenylene sulfide film
dielectric surface mount d.c. capacitors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regio
...