Tests on electric and optical fibre cables under fire conditions - Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category C

IEC 60332-3-24:2018 RLV contains both the official IEC International Standard and its Redline version. The Redline version is not an official document, it is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition.
IEC 60332-3-24:2018 covers category C for methods of test for the assessment of vertical flame spread of vertically mounted bunched wires or cables, electrical or optical, under defined conditions. This document relates to cables installed on the test ladder to achieve a nominal total volume of non-metallic material of 1,5 l/m of test sample. The flame application time is 20 min. The method of mounting uses the front of the standard ladder. The category is intended for general use where low volumes of non-metallic material are required to be evaluated. The test is intended for type approval testing. The requirements for the selection of cables for testing are given in Annex A. The flame spread is measured as the extent of damage of the cable sample. This procedure can be used to demonstrate the cable’s ability to limit flame spread. A recommended performance requirement is given in Annex B. This second edition cancels and replaces the first edition published in 2000 and Amendment 1:2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) adjustments have been made to the title, and elsewhere, to emphasise the standard is applicable to optical fibre cables as well as metallic conductor types;
b) details of the way in which cables are mounted on the ladder have been better defined in order to improve repeatability and reproducibility.
It has the status of a group safety publication in accordance with IEC Guide 104.
The contents of the interpretation sheet 1 of January 2019 have been included in this copy.

Essais des câbles électriques et des câbles à fibres optiques soumis au feu - Partie 3-24: Essai de propagation verticale de la flamme des fils ou câbles montés en nappes en position verticale - Catégorie C

IEC 60332-3-24:2018 est disponible sous forme de IEC 60332-3-24:2018 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
L’IEC 60332-3-24:2018 couvre la catégorie C pour les méthodes d'essai pour l'évaluation de la propagation verticale de la flamme des fils ou câbles électriques ou optiques, disposés en nappes en position verticale, dans des conditions définie. Le présent document concerne les câbles montés sur l'échelle d'essai afin d’obtenir un volume total nominal de matériau non métallique de 1,5 l/m d'échantillon d'essai. La durée d'application de la flamme est de 20 min. La méthode de montage utilise la face avant de l'échelle standard. Cette catégorie est prévue pour une utilisation générale lorsqu’il est requis d'évaluer le comportement de volumes faibles de matériau non métallique. L'essai est prévu pour les essais d'acceptation de type. Les exigences pour la sélection des câbles pour l'acceptation de type sont données à l'Annexe A. La propagation de la flamme est mesurée comme étant l'étendue de la partie endommagée de l'échantillon de câble. Cette procédure peut être utilisée pour démontrer l’aptitude du câble à limiter la propagation de la flamme. L’Annexe B donne une recommandation pour l'exigence de performance. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) des ajustements ont été apportés au titre, et ailleurs, afin de souligner que la Norme s’applique aux câbles à fibre optique, ainsi qu’aux types de conducteurs métalliques;
b) les détails sur la manière dont les câbles sont montés sur l'échelle ont été mieux définis afin d'améliorer la répétabilité et la reproductibilité.
Elle a le statut d’une publication groupée de sécurité conformément au Guide IEC 104.

General Information

Status
Published
Publication Date
12-Jul-2018
Technical Committee
Current Stage
PPUB - Publication issued
Completion Date
13-Jul-2018
Ref Project

Buy Standard

Standard
IEC 60332-3-24:2018 - Tests on electric and optical fibre cables under fire conditions - Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category C
English and French language
28 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

IEC 60332-3-24
Edition 2.0 2018-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
GROUP SAFETY PUBLICATION
PUBLICATION GROUPÉE DE SÉCURITÉ
Tests on electric and optical fibre cables under fire conditions –
Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or
cables – Category C
Essais des câbles électriques et des câbles à fibres optiques soumis au feu –
Partie 3-24: Essai de propagation verticale de la flamme des fils ou câbles
montés en nappes en position verticale – Catégorie C
IEC 60332-3-24:2018-07(en-fr)
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2018 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from

either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC

copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or

your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite

ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie

et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des

questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez

les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC

The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes

International Standards for all electrical, electronic and related technologies.
About IEC publications

The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the

latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org

The stand-alone application for consulting the entire The world's leading online dictionary of electronic and

bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in

Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional

documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical

iPad. Vocabulary (IEV) online.

IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary

The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and

variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of

committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been

and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc

details all new publications released. Available online and If you wish to give us your feedback on this publication or

also once a month by email. need further assistance, please contact the Customer Service

Centre: sales@iec.ch.
A propos de l'IEC

La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des

Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC

Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la

plus récente, un corrigendum ou amendement peut avoir été publié.
Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements
Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales,
électriques. Il contient 21 000 termes et définitions en anglais
Spécifications techniques, Rapports techniques et autres
et en français, ainsi que les termes équivalents dans 16
documents de l'IEC. Disponible pour PC, Mac OS, tablettes
langues additionnelles. Egalement appelé Vocabulaire
Android et iPad.
Electrotechnique International (IEV) en ligne.
Recherche de publications IEC -
Glossaire IEC - std.iec.ch/glossary
webstore.iec.ch/advsearchform
67 000 entrées terminologiques électrotechniques, en anglais

La recherche avancée permet de trouver des publications IEC et en français, extraites des articles Termes et Définitions des

en utilisant différents critères (numéro de référence, texte, publications IEC parues depuis 2002. Plus certaines entrées

comité d’études,…). Elle donne aussi des informations sur les antérieures extraites des publications des CE 37, 77, 86 et

projets et les publications remplacées ou retirées. CISPR de l'IEC.

IEC Just Published - webstore.iec.ch/justpublished Service Clients - webstore.iec.ch/csc

Restez informé sur les nouvelles publications IEC. Just Si vous désirez nous donner des commentaires sur cette

Published détaille les nouvelles publications parues. publication ou si vous avez des questions contactez-nous:

Disponible en ligne et aussi une fois par mois par email. sales@iec.ch.
---------------------- Page: 2 ----------------------
IEC 60332-3-24
Edition 2.0 2018-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
GROUP SAFETY PUBLICATION
PUBLICATION GROUPÉE DE SÉCURITÉ
Tests on electric and optical fibre cables under fire conditions –
Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or
cables – Category C
Essais des câbles électriques et des câbles à fibres optiques soumis au feu –
Partie 3-24: Essai de propagation verticale de la flamme des fils ou câbles
montés en nappes en position verticale – Catégorie C
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.220.40; 29.060.20 ISBN 978-2-8322-5800-2

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 3 ----------------------
IEC 60332-3-24:2018/ISH1:2019 – 1 –
 IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
IEC 60332-3-24
Edition 2.0 2018-07
TESTS ON ELECTRIC AND OPTICAL
FIBRE CABLES UNDER FIRE CONDITIONS –
Part 3-24: Test for vertical flame spread of vertically-mounted
bunched wires or cables – Category C
INTERPRETATION SHEET 1

This interpretation sheet has been prepared by IEC technical committee 20: Electric cables.

The text of this interpretation sheet is based on the following documents:
DISH Report on voting
20/1853/DISH 20/1864/RVDISH

Full information on the voting for the approval of this interpretation sheet can be found in the

report on voting indicated in the above table.
___________

The request to clarify the retest procedure was considered by TC 20/WG 18 and a common

view from the experts has been communicated:

1) The selection of the two retest samples should be agreed between manufacturer and

testing/certification body.

2) The retest samples shall be of exactly the same construction (same number of cores,

same conductor cross section, same design) as of the first test sample (that failed).

3) The retest samples should be taken from the same cable length as of the first test sample,

but WG18 finds it acceptable that, in case sufficient length is not available anymore, the

retest samples are taken from another production length/order (of the same construction).

In case the cable design is changed, it is no longer considered a retest sample, but a

different/new test sample.
ICS 13.220.40; 29.060.20
IEC 60332-3-24:2018-07/ISH1:2019-01(en)
---------------------- Page: 4 ----------------------
– 2 – IEC 60332-3-24:2018 © IEC 2018
CONTENTS

FOREWORD ......................................................................................................................... 3

INTRODUCTION ................................................................................................................... 5

1 Scope ............................................................................................................................ 6

2 Normative references..................................................................................................... 6

3 Terms and definitions .................................................................................................... 6

4 Test apparatus .............................................................................................................. 7

4.1 General ................................................................................................................. 7

4.2 Ignition source ...................................................................................................... 7

5 Test procedure .............................................................................................................. 7

5.1 Test sample .......................................................................................................... 7

5.2 Determination of the number of test pieces ............................................................ 7

5.3 Mounting of the test sample ................................................................................... 8

5.3.1 Cables having at least one conductor above 35 mm ...................................... 8

5.3.2 Cables having conductors 35 mm and below and optical cables .................... 8

5.4 Flame application time .......................................................................................... 9

6 Evaluation of test results ................................................................................................ 9

7 Performance requirements ........................................................................................... 10

8 Retest procedure ......................................................................................................... 10

9 Test report................................................................................................................... 10

Annex A (normative) Guidance on cable selection for type approval testing ......................... 12

Annex B (informative) Recommended performance requirements ........................................ 13

Bibliography ....................................................................................................................... 14

Figure 1 – Spaced cables mounted on the front side of the standard ladder ......................... 10

Figure 2 – Touching cables mounted on the front side of the standard ladder (arrays of

cables in contact) ............................................................................................................... 11

Table A.1 – Summary of test conditions ............................................................................... 12

---------------------- Page: 5 ----------------------
IEC 60332-3-24:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES
UNDER FIRE CONDITIONS –
Part 3-24: Test for vertical flame spread of
vertically-mounted bunched wires or cables – Category C
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 60332-3-24 has been prepared by IEC technical committee 20:

Electric cables.
This second edition cancels and replaces the first edition published in 2000 and
Amendment 1:2008. This edition constitutes a technical revision.

This edition includes the following significant technical changes with respect to the previous

edition:

a) adjustments have been made to the title, and elsewhere, to emphasise the standard is

applicable to optical fibre cables as well as metallic conductor types;

b) details of the way in which cables are mounted on the ladder have been better defined in

order to improve repeatability and reproducibility.
---------------------- Page: 6 ----------------------
– 4 – IEC 60332-3-24:2018 © IEC 2018

It has the status of a group safety publication in accordance with IEC Guide 104.

The text of this International Standard is based on the following documents:
FDIS Report on voting
20/1801/FDIS 20/1818/RVD

Full information on the voting for the approval of this International Standard can be found in

the report on voting indicated in the above table.

This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

A list of all parts in the IEC 60332 series, published under the general title Tests on electric

and optical fibre cables under fire conditions, can be found on the IEC website.

Future standards in this series will carry the new general title as cited above. Titles of existing

standards in this series will be updated at the time of the next edition.

The committee has decided that the contents of this document will remain unchanged until the

stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to

the specific document. At this date, the document will be
 reconfirmed,
 withdrawn,
 replaced by a revised edition, or
 amended.

The contents of the interpretation sheet 1 of January 2019 have been included in this copy.

---------------------- Page: 7 ----------------------
IEC 60332-3-24:2018 © IEC 2018 – 5 –
INTRODUCTION

IEC 60332-3-24 is part of a series of publications dealing with tests on electric and optical

fibre cables under fire conditions.
The IEC 60332-1 and IEC 60332-2 series specify methods of test for flame spread

characteristics for a single vertical insulated wire or cable. It cannot be assumed that,

because a cable or wire meets the requirements of the IEC 60332-1 and IEC 60332-2 series,

a vertical bunch of similar cables or wires will behave in a similar manner. This is because

flame spread along a vertical bunch of cables depends on a number of features, such as

a) the volume of combustible material exposed to the fire and to any flame which may be

produced by the combustion of the cables;

b) the geometrical configuration of the cables and their relationship to an enclosure;

c) the temperature at which it is possible to ignite the gases emitted from the cables;

d) the quantity of combustible gas released from the cables for a given temperature rise;

e) the volume of air passing through the cable installation;

f) the construction of the cable, for example armoured or unarmoured, multi- or single core.

All of the foregoing assume that the cables are able to be ignited when involved in an external

fire.

The IEC 60332-3 series gives details of a test where a number of cables are bunched

together to form various test sample installations. For easier use and differentiation of the

various test categories, the parts are designated as follows:
Part 3-10: Apparatus
Part 3-21: Category A F/R
Part 3-22: Category A
Part 3-23: Category B
Part 3-24: Category C
Part 3-25: Category D

Parts from 3-21 onwards define the various categories and the relevant procedures. The

categories are distinguished by test duration, the volume of non-metallic material of the test

sample and the method of mounting the sample for the test. In all categories, cables having at

least one conductor of cross-sectional area greater than 35 mm are tested in a spaced

configuration, whereas cables of conductor cross-sectional area of 35 mm or smaller and

optical fibre cables are tested in a touching configuration.

The categories are not necessarily related to different safety levels in actual cable

installations. The actual installed configuration of the cables may be a major determinant in

the level of flame spread occurring in an actual fire.

The method of mounting described as category A F/R (Part 3-21) is intended for special cable

designs used in particular installations.

Categories A, B, C and D (Part 3-22 to Part 3-25 respectively) are for general use where

different non-metallic volumes are applicable.
---------------------- Page: 8 ----------------------
– 6 – IEC 60332-3-24:2018 © IEC 2018
TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES
UNDER FIRE CONDITIONS –
Part 3-24: Test for vertical flame spread of
vertically-mounted bunched wires or cables – Category C
1 Scope

This part of IEC 60332 covers category C for methods of test for the assessment of vertical

flame spread of vertically mounted bunched wires or cables, electrical or optical, under

defined conditions.

This document relates to cables installed on the test ladder to achieve a nominal total volume

of non-metallic material of 1,5 l/m of test sample. The flame application time is 20 min. The

method of mounting uses the front of the standard ladder. The category is intended for

general use where low volumes of non-metallic material are required to be evaluated.

The test is intended for type approval testing. The requirements for the selection of cables for

testing are given in Annex A. The flame spread is measured as the extent of damage of the

cable sample. This procedure can be used to demonstrate the cable’s ability to limit flame

spread.
A recommended performance requirement is given in Annex B.

NOTE For the purposes of this document the term "electric wire or cable" covers all insulated metallic conductor

cables used for the conveyance of energy or signals.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their

content constitutes requirements of this document. For dated references, only the edition

cited applies. For undated references, the latest edition of the referenced document (including

any amendments) applies.

IEC 60332-3-10, Tests on electric and optical fibre cables under fire conditions – Part 3-10:

Test for vertical flame spread of vertically-mounted bunched wires or cables – Apparatus

IEC 60811-606, Electric and optical fibre cables – Test methods for non-metallic materials –

Part 606: Physical tests – Methods for determining the density
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following

addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
ignition source
source of energy that initiates combustion
---------------------- Page: 9 ----------------------
IEC 60332-3-24:2018 © IEC 2018 – 7 –
[SOURCE: ISO 13943:2017, 3.219]
3.2
char
carbonaceous residue resulting from pyrolysis or incomplete combustion
[SOURCE: ISO 13943:2017, 3.47]
3.3
flame spread
propagation of a flame front
[SOURCE: ISO 13943:2017, 3.168]
4 Test apparatus
4.1 General
The apparatus specified in IEC 60332-3-10 shall be used.
4.2 Ignition source
The ignition source shall be one ribbon-type propane gas burner as specified in
IEC 60332-3-10.
5 Test procedure
5.1 Test sample

The test sample shall comprise a number of test pieces of cable from the same production

length, each having a minimum length of 3,5 m.

The total number of test pieces in the test sample shall be that number required to provide a

nominal total volume of non-metallic material of 1,5 l/m of test sample.
The test sample for type approval shall be in accordance with Annex A.

The test pieces forming the test sample shall be conditioned at a temperature of (20 ± 10) °C

for at least 16 h before commencing the test. The test pieces shall be dry.
5.2 Determination of the number of test pieces

In order to calculate the appropriate number of test pieces, it is necessary to determine the

volume per metre of non-metallic material of one test piece.

A length of cable which shall be not less than 0,3 m long is carefully cut to ensure that the

surfaces are at right angles to the cable axis, thus enabling precise measurements of its

length.

The density of each non-metallic component (including cellular material) shall be measured in

an appropriate way, for example according to IEC 60811-606, in order to obtain values

expressed to the second decimal place.

Each non-metallic material C shall be removed from the test piece and weighed. Any non-

metallic material making up less than 5 % of the total non-metallic mass of the test piece shall

be assumed to have a density of 1,0 kg/dm .
---------------------- Page: 10 ----------------------
– 8 – IEC 60332-3-24:2018 © IEC 2018

Where semi-conducting screens cannot be removed from the insulating material, the

components may be considered as one for the purpose of measuring their mass and density.

The volume V (litres per metre of cable) of each non-metallic material C is calculated as

i i
follows:
V =
ρ ×l
where
M is the mass of the component C (kg);
i i
ρ is the density of the component C (kg/dm );
i i
l is the length of the test piece of cable (m).

The total volume, V, of the non-metallic materials contained in 1 m of cable is equal to the

sum of the individual volumes V , V , etc.
1 2

The number of test pieces to be mounted is obtained by taking the closest integer (0,5 and

above corresponding to 1) of the ratio of the volume per metre specified in 5.1 and the total

volume, V, of non-metallic material per metre of cable, subject to a minimum number of two

test pieces.
5.3 Mounting of the test sample
5.3.1 Cables having at least one conductor above 35 mm

For cables having at least one conductor with a cross-section exceeding 35 mm , each test

piece shall be attached individually to each rung of the ladder by means of metal wire (steel

or copper). For cables up to and including 50 mm diameter, use wire between 0,5 mm and

1,0 mm in diameter. For cables above 50 mm diameter, use wire between 1,0 mm and 2,5 mm

in diameter.

Test pieces shall be attached to the front of the standard ladder in a single layer up to a total

maximum width of 300 mm with a space between each test piece of 0,5 times the cable

diameter but not exceeding 20 mm (see Figure 1). There shall be a minimum distance of

50 mm between the edge of the test sample and the inside of the ladder uprights.

When mounting the test pieces, the first test piece shall be positioned approximately in the

centre of the ladder and further test pieces added on either side so that the whole array of

test pieces is approximately centred on the ladder.

Mount all test pieces on the ladder with the bending (due to bending of the cable on the reel),

if any, in the same direction, towards the back side of the test chamber as much as possible.

To achieve straight test pieces between the steel rungs below and above the burner position,

it is permitted to fix the test pieces to an additional horizontal support 200 mm to 300 mm

lower than the steel rung below the burner position.

NOTE The objective is to improve the repeatability and reproducibility of the test.

5.3.2 Cables having conductors 35 mm and below and optical cables

For cables having all conductors with cross-sections of 35 mm or smaller and optical cables,

each test piece shall be attached, either individually or as part of an array, to each rung of the

ladder by means of metal wire (steel or copper) between 0,5 mm and 1,0 mm in diameter.

---------------------- Page: 11 ----------------------
IEC 60332-3-24:2018 © IEC 2018 – 9 –

Test pieces shall be attached to the front of the standard ladder in touching formation in one

or more layers up to a maximum total width of 300 mm. There shall be a minimum distance of

50 mm between the edge of the test sample and the inside of the ladder uprights.

When mounting the test pieces, the first test piece or array of test pieces shall be positioned

approximately in the centre of the ladder and further test pieces or arrays added on either

side so that the test sample is approximately centred on the ladder.

Mount all test pieces on the ladder with the bending (due to bending of the cable on the reel),

if any, in the same direction, towards the back side of the test chamber as much as possible.

To achieve straight test pieces between the steel rungs below and above the burner position,

it is permitted to fix the test pieces to an additional horizontal support 200 mm to 300 mm

lower than the steel rung below the burner position.

In order to ensure that the test pieces are straight on the ladder, the test pieces shall be

maintained under tension manually while attaching the test pieces to the rung of the ladder by

means of a metal wire.

NOTE The objective is to improve the repeatability and reproducibility of the test.

If a second (or more) layer of test pieces is required after the full width of the ladder has been

utilized for the first (or following) layer, then the first test piece or array of test pieces in the

second (or following) layer shall be positioned approximately in the centre of the ladder and

further test pieces or arrays added on either side so that the second (or following) layer is

approximately centred on the ladder.

If a large number of test pieces is required to make up a test sample, the test pieces may be

attached to each rung of the ladder in flat arrays of cables of a maximum width of five test

pieces using the specified metal wire. For consistency, it is recommended that adjacent

arrays of cables are secured together at every rung to ensure that they are in touching

formation (see Figure 2).
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.