IEC 63171-2:2021

Connectors for electrical and electronic equipment - Part 2: Detail specification for 2-way, shielded or unshielded, free and fixed connectors: mechanical mating information, pin assignment and additional requirements for type 2

IEC 63171-2:2021 covers 2-way, shielded or unshielded, free and fixed connectors for data transmission up to 600 MHz, with current-carrying capacity, known as Type 2. It specifies the common dimensions, mechanical, electrical and transmission characteristics and environmental requirements as well as test specifications respectively. The form factor of these connectors allows their use for cable sharing with already installed TO’s for structured cabling. The overall performance of the transmission channel in such case has to be evaluated. Intermateable and interoperable versions for circular connector for sealed applications including this connector are described in IEC 63171-5. The shielded and unshielded connectors are interoperable for their internal transmission performance and can be exchanged. The shielded version has improved alien crosstalk and coupling attenuation properties.

General Information

• Status: Published
• Publication Date: 26-May-2021
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• Technical Committee: SC 48B - Electrical connectors
• Current Stage: PPUB - Publication issued
• Start Date: 04-Jun-2021
• Completion Date: 27-May-2021

Standards Content (Sample)

IEC 63171-2 ®
Edition 1.0 2021-05
INTERNATIONAL
STANDARD
Connectors for electrical and electronic equipment –
Part 2: Detail specification for 2-way, shielded or unshielded, free and fixed
connectors: mechanical mating information, pin assignment and additional
requirements for type 2
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: [phone]
3, rue de Varembé [e-mail]
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC online collection - oc.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 000 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 18 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc

If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: [e-mail].
IEC 63171-2 ®
Edition 1.0 2021-05
INTERNATIONAL
STANDARD
Connectors for electrical and electronic equipment –

Part 2: Detail specification for 2-way, shielded or unshielded, free and fixed

connectors: mechanical mating information, pin assignment and additional

requirements for type 2
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 31.220.10 ISBN 978-2-8322-9778-0

– 2 – IEC 63171-2:2021 © IEC 2021
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 Common features and typical connector pair . 8
4.1 Mating information . 8
5 Characteristics . 14
5.1 General . 14
5.2 Pin assignment . 15
5.3 Classification into climatic category . 15
5.4 Electrical characteristics . 15
5.5 Transmission characteristics . 16
5.6 Mechanical characteristics . 17
6 Tests and test schedule . 17
6.1 General . 17
6.2 Arrangement for interface contact resistance measurement . 18
6.3 Arrangement for vibration test . 19
6.4 Test procedures and measuring methods . 19
6.5 Preconditioning . 19
6.6 Test schedules . 19
Bibliography . 21

Figure 1 – Relationships between the IEC 63171 series and their related references . 5
Figure 2 – Shielded fixed connector details . 9
Figure 3 – Unshielded fixed connector details . 11
Figure 4 – Shielded free connector . 12
Figure 5 – Unshielded free connector . 14
Figure 6 – Fixed connector pin assignment (front view of connector) . 15
Figure 7 – Arrangement for interface contact resistance measurement . 18
Figure 8 – Arrangement for vibration test . 19

Table 1 – Dimensions for Figure 2 and Figure 3 . 10
Table 2 – Dimensions for Figure 4 and Figure 5 . 13
Table 3 – Creepage and clearance distances . 16

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT –

Part 2: Detail specification for 2-way, shielded or unshielded,
free and fixed connectors: mechanical mating information,
pin assignment and additional requirements for type 2

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 63171-2 has been prepared by subcommittee 48B: Electrical connectors, of IEC technical
committee 48: Electrical connectors and mechanical structures for electrical and electronic
equipment. It is an International Standard.
The text of this International Standard is based on the following documents:
FDIS Report on voting
48B/2875/FDIS 48B/2886/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.

– 4 – IEC 63171-2:2021 © IEC 2021
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts in the IEC 63171 series, published under the general title Connectors for
electrical and electronic equipment, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
INTRODUCTION
IEC 63171 is the base specification of the whole series. Subsequent specifications do not
duplicate information given in the base document, but list only additional requirements. For
complete specification regarding a component of a higher number document, all lower
numbered documents must be considered as well. Figure 1 shows the interrelation of the
documents:
Figure 1 – Relationships between the IEC 63171 series and their related references
NOTE IEC 63171-1 and IEC 63171-6 contain duplicate information, which is either equal to or better than the
minimum requirements of IEC 63171; such duplicate information is due to be removed in later editions.
This document refers to International Standards for test and measurement, environmental
testing as well as solderless connections.

– 6 – IEC 63171-2:2021 © IEC 2021
IEC SC 48B – Electrical connectors
IEC 63171-2 Ed. 1
Specification available from:
IEC General secretariat
or from the addresses shown on the inside cover.
Shielded connector with snap-
in mechanism
Shielded connector with
locking device
Unshielded connector with
snap-in mechanism
Unshielded connector with
locking device
CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT –

Part 2: Detail specification for 2-way, shielded or unshielded,
free and fixed connectors: mechanical mating information,
pin assignment and additional requirements for type 2

1 Scope
This part of IEC 63171 covers 2-way, shielded or unshielded, free and fixed connectors for data
transmission up to 600 MHz, with current-carrying capacity, known as Type 2. It specifies the
common dimensions, mechanical, electrical and transmission characteristics and environmental
requirements as well as test specifications respectively.
The form factor of these connectors allows their use for cable sharing with already installed
TO’s for structured cabling.
NOTE The overall performance of the transmission channel in such case has to be evaluated
...