IEC 60938-2-2:1999
(Main)Fixed inductors for electromagnetic interference suppression - Part 2-2: Blank detail specification - Inductors for which safety tests are required (only)
Fixed inductors for electromagnetic interference suppression - Part 2-2: Blank detail specification - Inductors for which safety tests are required (only)
IEC 60938-2-2:1999 forms the basis for a uniform procedure for a common mark. It implements the approval schedule for safety tests only in IEC 60938-2, requires a declaration of design for parameters relevant to safety tests and prescribes conformance tests to be conducted on every lot prior to its release and re-qualification tests depending on changes of the design.
Inductances fixes d'antiparasitage - Partie 2-2: Spécification particulière cadre - Inductances nécessitant des essais de sécurité (uniquement)
La CEI 60938-2-2:1999 constitue la base d'une procédure uniforme de marquage commun. Elle met en oeuvre le programme d'homologation pour les essais de sécurité uniquement de la CEI 60938-2, nécessite une déclaration de conception pour les paramètres relatifs aux essais de sécurité et indique les essais de conformité à réaliser sur tous les lots avant leur livraison et les essais de requalification en fonction des modifications apportées à la conception.
General Information
Standards Content (sample)
IEC 60938-2-2
Edition 1.0 1999-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fixed inductors for electromagnetic interference suppression –
Part 2-2: Blank detail specification – Inductors for which safety tests are
required (only)
Inductances fixes d’antiparasitage –
Partie 2-2: Spécification particulière cadre – Inductances nécessitant des essais
de sécurité (uniquement)IEC 60938-2-2:1999
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 1999 IEC, Geneva, Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les
microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 113, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.Useful links:
IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org
The advanced search enables you to find IEC publications The world's leading online dictionary of electronic and
by a variety of criteria (reference number, text, technical electrical terms containing more than 30 000 terms and
committee,…). definitions in English and French, with equivalent terms inIt also gives information on projects, replaced and additional languages. Also known as the International
withdrawn publications. Electrotechnical Vocabulary (IEV) on-line.IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc
Stay up to date on all new IEC publications. Just Published If you wish to give us your feedback on this publication
details all new publications released. Available on-line and or need further assistance, please contact the
also once a month by email. Customer Service Centre: csc@iec.ch.A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEILe contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.Liens utiles:
Recherche de publications CEI - www.iec.ch/searchpub Electropedia - www.electropedia.org
La recherche avancée vous permet de trouver des Le premier dictionnaire en ligne au monde de termes
publications CEI en utilisant différents critères (numéro de électroniques et électriques. Il contient plus de 30 000
référence, texte, comité d’études,…). termes et définitions en anglais et en français, ainsi que
Elle donne aussi des informations sur les projets et les les termes équivalents dans les langues additionnelles.
publications remplacées ou retirées. Egalement appelé Vocabulaire Electrotechnique
International (VEI) en ligne.Just Published CEI - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications de la CEI.
Just Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur
Disponible en ligne et aussi une fois par mois par email. cette publication ou si vous avez des questions
contactez-nous: csc@iec.ch.---------------------- Page: 2 ----------------------
IEC 60938-2-2
Edition 1.0 1999-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fixed inductors for electromagnetic interference suppression –
Part 2-2: Blank detail specification – Inductors for which safety tests are
required (only)
Inductances fixes d’antiparasitage –
Partie 2-2: Spécification particulière cadre – Inductances nécessitant des essais
de sécurité (uniquement)INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX J
ICS 29.100.10; 31.020 ISBN 978-2-83220-772-7
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical CommissionMarque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 3 ----------------------
– 2 – 60938-2-2 © IEC:1999
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIXED INDUCTORS FOR ELECTROMAGNETIC
INTERFERENCE SUPPRESSION –
Part 2-2: Blank detail specification –
Inductors for which safety tests are required (only)
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60938-2-2 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.This bilingual version (2013-05) corresponds to the monolingual English version, published in
1999-10.The text of this standard is based on the following documents:
FDIS Report on voting
40/1113/FDIS 40/1139/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.The French version of this standard has not been voted upon.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.
Annex A forms an integral part of this standard.---------------------- Page: 4 ----------------------
60938-2-2 © IEC:1999 – 3 –
The committee has decided that this publication remains valid until 2005.
At this date, in accordance with the committee’s decision, the publication will be
• reconfirmed;• withdrawn;
• replaced by a revised edition, or
• amended.
---------------------- Page: 5 ----------------------
– 4 – 60938-2-2 © IEC:1999
FIXED INDUCTORS FOR ELECTROMAGNETIC
INTERFERENCE SUPPRESSION –
Part 2-2: Blank detail specification –
Inductors for which safety tests are required (only)
INTRODUCTION
Blank detail specification
This blank detail specification forms the basis for a uniform procedure for a common mark. It
implements the approval schedule for safety tests only in IEC 60938-2, requires a declaration
of design for parameters relevant to safety tests and prescribes conformance tests to be
conducted on every lot prior to its release and re-qualification tests depending on changes of
the design.In comparison with IEC 60938-2-1 which provides safety tests and performance tests, this
specification is restricted to safety tests only.The use of IEC 60938-2-1 may be more appropriate for components manufactured in mass
production, whereas this specification may be necessary in those cases where approval and re-
qualification tests contribute considerably to the costs of the product.A blank detail specification is a supplementary document to the sectional specification and
contains requirements for style and layout and minimum content of detail specifications. In the
preparation of detail specifications the content of 1.4 of the sectional specification shall be
taken into account.The numbers between square brackets on the first page of the detail specification correspond
to the following information which shall be inserted in the position indicated.Identification of the detail specification and of the inductor
The first page of the detail specification should have the layout recommended on the next page
of this blank detail specification.[0] Manufacturer's name.
[0A] Manufacturer's style designation.
[1] The "International Electrotechnical Commission" or the National Standards Organisation
under whose authority the detail specification is drafted.[2] The IEC or National Standards number of the detail specification, date of issue and any
further information required by the national system.[3] The number and issue number of the IEC or national generic specification.
[4] The IEC number of the blank detail specification.
Identification of the inductor
[5] A short description of the inductor or range of inductors.
[6] Information on typical construction (when applicable).
---------------------- Page: 6 ----------------------
60938-2-2 © IEC:1999 – 5 –
[7] Outline drawing with main dimensions which are of importance for interchangeability
and/or reference to the national or international documents for outlines. Alternatively, this
drawing may be given in an annex to the detail specification, but should always contain
an illustration of the general outer appearance of the inductor.[8] Reference data on the most important properties, to allow comparison between the
various inductor types intended for the same, or for similar applications.[1] IEC 60938-2-1XX [2]
QC XXXXXXXXXXXX
ELECTRONIC COMPONENTS OF ASSESSED IEC 60938-2-2 [4]
QUALITY IN ACCORDANCE WITH: QC XXXXXX
[3] FIXED INDUCTORS FOR
ELECTROMAGNETIC INTERFERENCE
SUPPRESSION FOR WHICH SAFETY [5]
Outline drawing: (see table 1) TESTS ARE REQUIRED
(... angle projection)
[7] [6]
(Other shapes are permitted within the dimensions
given)
Safety tests only [8]
NOTES [1] to [9] see pages 3 and 4.
Information on the availability of components qualified
to this detail specification is given in the Register
of Approvals.
1 General data
1.1 Recommended method(s) of mounting (to be inserted)
(See 1.4.3 of IEC 60938-2.)
---------------------- Page: 7 ----------------------
– 6 – 60938-2-2 © IEC:1999
1.2 Dimensions
Table 1 – Dimensions related to case size
Dimensions
Case size
reference or
type
L W H L L L
1 2 3 4
NOTE 1 – When there is no case size reference, the dimensions should be given per type
designation.NOTE 2 – The dimensions should be given as maximum dimensions or as nominal dimensions with
a tolerance.1.3 Ratings and characteristics
) (see table 2)
Rated inductance (L
Tolerance on rated inductance
Rated current (I) range (see table 2)
DC resistance (R) (see table 2)
Rated voltage
Rated temperature
Climatic category
Category of passive flammability (if applicable)
Table 2 – Values of inductance, rated current and
d.c. resistance related to type designation
Ordering code, type L I R
R R max
designation
per line per line
mH A Ω
1.4 Related documents
Generic specification: IEC 60938-1:1999, Fixed inductors for electromagnetic interference
suppression – Part 1: Generic specificationSectional specification: IEC 60938-2:1999, Fixed inductors for electromagnetic interference
suppression – Part 2: Sectional specification---------------------- Page: 8 ----------------------
60938-2-2 © IEC:1999 – 7 –
1.5 Marking
The marking of the inductor shall be in accordance with the requirements of 1.6 of
IEC 60938-2.The details of the marking of the component and package shall be given in full in the detail
specification.1.6 Ordering information
Orders for inductors covered by this specification shall contain, in clear or in coded form, the
following minimum information:a) type designation;
b) rated inductance;
c) tolerance on rated inductance;
d) rated voltage;
e) rated current;
f) number and issue reference of the detail specification and style reference.
1.7 Additional information (not for inspection purposes)
1.8 Additional or increased severities or requirements to those specified in the generic
or sectional specificationNOTE – Additions or increased requirements should be specified only when essential.
Table 3 – Other characteristicsThis table is to be used for defining characteristics
which are additional to or more severe than those given
in the sectional specification.
2 Inspection requirements
2.1 Procedures
For qualification approval, the procedures shall be in accordance with 3.4 of IEC 60938-2.
2.2 Test schedules2.2.1 Initial approval
See table 1 and annex A of the sectional specification.
2.2.2 Conformance tests
See table 4 of this specification in association with annex A of this specification.
2.2.2.1 Conformance tests (lot-by-lot)---------------------- Page: 9 ----------------------
– 8 – 60938-2-2 © IEC:1999
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.