IEC 60255-26:2008
(Main)Measuring relays and protection equipment - Part 26: Electromagnetic compatibility requirements
Measuring relays and protection equipment - Part 26: Electromagnetic compatibility requirements
IEC 60255-26:2008 is applicable to measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with those systems; it specifies the essential requirements for electromagnetic compatibility for measuring relays and protection equipment intended to be used at industrial locations. The main difference of this new edition with respect to the previous one concerns the references to IEC 61000-4 and to CISPR 22.
Relais de mesure et dispositifs de protection - Partie 26: Exigences de compatibilité électromagnétique
La CEI 60255-26:2008 est applicable aux relais de mesure et dispositifs de protection pour la protection des réseaux d'énergie, y compris les fonctions de contrôle, surveillance et communication intégrées, utilisées dans ces réseaux; cette norme spécifie les exigences de compatibilité électromagnétique pour les relais de mesure et dispositifs de protection destinés à être utilisés dans des locaux industriels. La principale différence de cette nouvelle édition par rapport à la précédente est relative à la référence à la CEI 61000-4 et à la CISPR 22.
General Information
Relations
Standards Content (Sample)
IEC 60255-26
Edition 2.0 2008-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Measuring relays and protection equipment –
Part 26: Electromagnetic compatibility requirements
Relais de mesure et dispositifs de protection –
Partie 26: Exigences de compatibilité électromagnétique
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 60255-26
Edition 2.0 2008-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Measuring relays and protection equipment –
Part 26: Electromagnetic compatibility requirements
Relais de mesure et dispositifs de protection –
Partie 26: Exigences de compatibilité électromagnétique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
N
CODE PRIX
ICS 29.120.70; 33.100.10; 33.100.20 ISBN 2-8318-9853-6
– 2 – 60255-26 © IEC:2008
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope and object.6
1.1 Emission .6
1.2 Immunity .6
2 Normative references .7
3 Terms and definitions .8
4 Test requirements and procedures .9
4.1 Emission tests.9
4.2 Immunity tests.9
5 Criteria for acceptance .9
5.1 Emission tests.9
5.2 Immunity tests.9
6 Test report.9
Figure 1 – Ports for measuring relays and protection equipment .9
Table 1 – Emission tests – Enclosure port .9
Table 2 – Emission tests – Auxiliary power supply port .10
Table 3 – Immunity tests – Enclosure port .10
Table 4 – Immunity tests – Auxiliary power supply port .11
Table 5 – Immunity tests – Communication port.12
Table 6 – Immunity tests – Input and output ports.13
Table 7 – Immunity tests – Functional earth port.14
60255-26 © IEC:2008 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MEASURING RELAYS AND PROTECTION EQUIPMENT –
Part 26: Electromagnetic compatibility requirements
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60255-26 has been prepared by IEC technical committee 95:
Measuring relays and protection equipment.
This second edition cancels and replaces the first edition published in 2004. This edition
constitutes a technical revision.
The main difference with respect to the previous edition concerns the reference to IEC 61000-
4 series and to CISPR 22.
The text of this standard is based on the following documents:
FDIS Report on voting
95/230/FDIS 95/234/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
– 4 – 60255-26 © IEC:2008
A list of all parts of IEC 60255 series under the general title Measuring relays and protection
equipment, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
60255-26 © IEC:2008 – 5 –
INTRODUCTION
This part of IEC 60255 specifies all of the requirements for electromagnetic compatibility in a
single document. As such, it is considered as an overview document for measuring relays and
protection equipment. The detailed test procedures are given in other referenced standards.
– 6 – 60255-26 © IEC:2008
MEASURING RELAYS AND PROTECTION EQUIPMENT –
Part 26: Electromagnetic compatibility requirements
1 Scope and object
This part of IEC 60255 is applicable to measuring relays and protection equipment for power
system protection, including the control, monitoring and process interface equipment used
with those systems.
This standard specifies the essential requirements for electromagnetic compatibility for
measuring relays and protection equipment intended to be used at industrial locations.
Measuring relays and protection equipment used in substations and power plants may require
higher immunity test levels.
For equipment not incorporating electronic circuits, for example electromechanical relays,
tests according to this standard are not required.
The requirements specified in this standard are applicable to measuring relays and protection
equipment in a new condition and all tests specified are type tests only.
1.1 Emission
The object of this standard is to specify limits and test methods, for measuring relays and
protection equipment in relation to electromagnetic emissions which may cause interference
in other equipment.
These emission limits represent electromagnetic compatibility essential requirements and
have been selected to ensure that the disturbances generated by measuring relays and
protection equipment, operated normally in substations and power plants, do not exceed a
level which could prevent other equipment from operating as intended.
Test requirements are specified for the enclosure and power su
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.