ISO 6721-7:2019
(Main)Plastics — Determination of dynamic mechanical properties — Part 7: Torsional vibration — Non-resonance method
Plastics — Determination of dynamic mechanical properties — Part 7: Torsional vibration — Non-resonance method
This document describes a torsional, non-resonance method for determining the components of the shear complex modulus G* of solid polymers in the form of bars or rods at frequencies typically in the range 0,001 Hz to 100 Hz. Higher-frequency measurements can be made, but significant errors in the dynamic properties measured are likely to result (see 10.2.1 and 10.2.2). The method is suitable for measuring dynamic storage moduli ranging from about 10 MPa, which is typical of values obtained for stiff rubbers, to values of about 10 GPa which are representative of fibre-reinforced plastics. Although materials with moduli less than 10 MPa can be studied, more accurate measurements of their dynamic properties can be made using simple shear (see ISO 6721-6) or torsional deformations of thin layers between parallel plates. This method is particularly suited to the measurement of loss factors greater than 0,02 and may therefore be conveniently used to study the variation of dynamic properties with temperature and frequency through most of the glass-rubber relaxation region (see ISO 6721‑1). The availability of data determined over wide ranges of both frequency and temperature enable master plots to be derived, using frequency-temperature shift procedures, which display dynamic properties over an extended frequency range at different temperatures. NOTE Although loss factors below 0,1 can be more accurately determined using the torsion pendulum (see ISO 6721‑2), the method described in this document enables a much wider and continuous frequency range to be covered.
Plastiques — Détermination des propriétés mécaniques dynamiques — Partie 7: Vibration en torsion — Méthode hors résonance
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 6721-7
Second edition
2019-04
Plastics — Determination of dynamic
mechanical properties —
Part 7:
Torsional vibration — Non-
resonance method
Plastiques — Détermination des propriétés mécaniques
dynamiques —
Partie 7: Vibration en torsion — Méthode hors résonance
Reference number
ISO 6721-7:2019(E)
©
ISO 2019
---------------------- Page: 1 ----------------------
ISO 6721-7:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 6721-7:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Test device . 2
5.1 Loading assembly . 2
5.1.1 General. 2
5.1.2 Clamps . 2
5.1.3 Transducers. 2
5.2 Electronic data-processing equipment . 3
5.3 Temperature measurement and control . 3
5.4 Devices for measuring test specimen dimensions . 3
6 Test specimens. 3
6.1 General . 3
6.2 Shape and dimensions . 3
6.3 Preparation . 3
7 Number of specimens . 3
8 Conditioning .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.