ISO 18752:2006/Amd 1:2010

Rubber hoses and hose assemblies — Wire- or textile-reinforced single-pressure types for hydraulic applications — Specification — Amendment 1

Tuyaux et flexibles en caoutchouc — Types hydrauliques avec armature de fils métalliques tressés — Spécifications — Amendement 1

General Information

• Status: Withdrawn
• Publication Date: 21-Sep-2010
• Withdrawal Date: 21-Sep-2010
• ICS: 23.040.70 - Hoses and hose assemblies
• Technical Committee: ISO/TC 45/SC 1 - Rubber and plastics hoses and hose assemblies
• Drafting Committee: ISO/TC 45/SC 1/WG 3 - Hydraulic hoses
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 03-Feb-2011

Relations

• Revised: ISO 18752:2012 - Rubber hoses and hose assemblies — Wire- or textile-reinforced single-pressure types for hydraulic applications — Specification
• Effective Date: 27-Nov-2010
• Amends: ISO 18752:2006 - Rubber hoses and hose assemblies — Wire- or textile-reinforced single-pressure types for hydraulic applications — Specification
• Effective Date: 09-May-2020

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 18752
First edition
2006-07-15
AMENDMENT 1
2010-10-01


Rubber hoses and hose assemblies —
Wire- or textile-reinforced single-pressure
types for hydraulic applications —
Specification
AMENDMENT 1
Tuyaux et flexibles en caoutchouc — Types hydrauliques avec
armature de fils métalliques tressés — Spécifications
AMENDEMENT 1





Reference number
ISO 18752:2006/Amd.1:2010(E)
©
ISO 2010

---------------------- Page: 1 ----------------------
ISO 18752:2006/Amd.1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 18752:2006/Amd.1:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of techn
...