ISO 2698:2013
(Main)Diesel engines — Clamp-mounted fuel injectors, types 7 and 28
Diesel engines — Clamp-mounted fuel injectors, types 7 and 28
ISO 2698:2013 specifies dimensions necessary for the mounting of fuel injectors in diesel (compression-ignition) engines. The location of the fuel inlet and leak-off connections, and the dimensions of the clamp are not defined since they vary according to the particular application. ISO 2698:2013 applies to clamp-mounted injectors of types 7 and 28 made of an integral nozzle and nozzle holder design with a 9,5 mm (nominal) injector shank diameter.
Moteurs à allumage par compression — Porte-injecteurs de combustible complets à fixation par patte, types 7 et 28
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 2698
Third edition
2013-05-15
Diesel engines — Clamp-mounted fuel
injectors, types 7 and 28
Moteurs à allumage par compression — Porte-injecteurs de
combustible complets à fixation par patte, types 7 et 28
Reference number
ISO 2698:2013(E)
©
ISO 2013
---------------------- Page: 1 ----------------------
ISO 2698:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 2698:2013(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Dimensions and tolerances . 1
2.1 Injectors, types 7 and 28 . 1
2.2 Clamp location . 3
2.3 Preferred length L .4
3 Other specifications . 5
Bibliography . 6
© ISO 2013 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 2698:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 22, Road
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.