ISO/TS 3669-2:2007
(Main)Vacuum technology — Bakable flanges — Part 2: Dimensions of knife-edge flanges
Vacuum technology — Bakable flanges — Part 2: Dimensions of knife-edge flanges
ISO/TS 3669-2:2007 specifies the dimensions of fixed or rotatable bolted knife-edge style bakable flanges used in vacuum systems for pressures ranging from atmospheric to as low as 10-13 Pa.
Technique du vide — Brides étuvables — Partie 2: Dimensions des brides à guillotine
General Information
Relations
Standards Content (Sample)
TECHNICAL ISO/TS
SPECIFICATION 3669-2
First edition
2007-09-01
Vacuum technology — Bakable flanges —
Part 2:
Dimensions of knife-edge flanges
Technique du vide — Brides étuvables —
Partie 2: Dimensions des brides à guillotine
Reference number
ISO/TS 3669-2:2007(E)
©
ISO 2007
---------------------- Page: 1 ----------------------
ISO/TS 3669-2:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TS 3669-2:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of normative document:
⎯ an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
⎯ an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 3669-2 was prepared by Technical Committee ISO/TC 112, Vacuum technology.
ISO 3669 consists of the following parts, under the general title Vacuum technology — Bakable flanges:
⎯ Dimensions
⎯ Part 2: Dimensions of knife-edge flanges [Technical Specification]
© ISO 2007 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/TS 3669-2:2007(E)
Introduction
This Technical Specification contains significant technical changes from ISO 3669:1986, which defined two
series of bakable flanges:
⎯ a preferred series, the main dimensions of which ensure compatibility with already standardized non-
bakable flanges (see ISO 1609);
⎯ a secondary series corresponding to flanges in common use.
This part of ISO 3669 specifies only one series and is no longer dependent on the preferred number.
Effectively, the preferred series has been made obsolete, thereby promoting the secondary series into being
the one and only set of specified dimensions. Furthermore, several dimensions in what was formerly the
secondary series have been modified to correspond to flanges in common use. Finally, detailed dimensions
for the knife-edge sealing profile have been incorporated.
iv © ISO 2007 – All rights reserved
---------------------- Page: 4 ----------------------
TECHNICAL SPECIFICATION ISO/TS 3669-2:2007(E)
Vacuum technology — Bakable flanges —
Part 2:
Dimensions of knife-edge flanges
1 Scope
This part of ISO 3669 specifies the dimensions of fixed or rotatable bolted knife-edge style bakable flanges
–13
used in vacuum systems for pressures ranging from atmospheric to as low as 10 Pa.
2 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
2.1
knife-edge style flange
metal sealed flange used for high and ultra-high vacuum service
NOTE 1 The sandwiching of one metal gasket between two knife-edge flanges and securely bolting these together
makes a vacuum-tight joint. The seal is made when the conical knife edge profile of the flange cuts into the flat surface of
a metal gasket.
1)
NOTE 2 Originally developed as Conflat flanges. The widespread and continued use of knife-edge flanges has made
these a de facto international standard, codified by this Technical Specification.
2.2
nominal bore
value intended to both identify the flange and specify the largest practical size of tubing that can be
accommodated by the flange
NOTE See Table 1, in which the convention of identifying original flanges by the outside diameter of the flange
(historically in inches) has been maintained.
2.3
leak check groove
groove machined into the seal side of the flange to facilitate the free passage of search gas from the outer
perimeter of the flange to the seal zone near the metal gasket
1) Conflat® is the trade name of a product supplied by Varian Corporation. This information is given for the convenience
of users of this Technical Specification and does not constitute an endorsement by ISO of the product named. Equivalent
products may b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.