Road vehicles — Liquefied natural gas (LNG) fuel system components — Part 15: Capacitance fuel content gauge

ISO 12614-15:2014 specifies tests and requirements for the capacitance fuel content gauge, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. ISO 12614-15:2014 is applicable to vehicles using natural gas in accordance with ISO 15403 (mono-fuel, bi-fuel, or dual-fuel applications). It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refueling receptacles.

Véhicules routiers — Équipements pour véhicules utilisant le gaz naturel liquéfié (GNL) comme combustible — Partie 15: Jauge de capacité

General Information

Status
Withdrawn
Publication Date
02-Jul-2014
Withdrawal Date
02-Jul-2014
Current Stage
9599 - Withdrawal of International Standard
Completion Date
04-Jun-2021
Ref Project

Relations

Buy Standard

Standard
ISO 12614-15:2014 - Road vehicles -- Liquefied natural gas (LNG) fuel system components
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 12614-15:2014 - Road vehicles -- Liquefied natural gas (LNG) fuel system components
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 12614-15
First edition
2014-07-01
Road vehicles — Liquefied natural gas
(LNG) fuel system components —
Part 15:
Capacitance fuel content gauge
Véhicules routiers — Équipements pour véhicules utilisant le gaz
naturel liquéfié (GNL) comme combustible —
Partie 15: Jauge de capacité
Reference number
ISO 12614-15:2014(E)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO 12614-15:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 12614-15:2014(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Marking . 2
5 Construction and assembly . 2
6 Test . 3
6.1 Applicability . 3
6.2 Insulation resistance . 3
© ISO 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 12614-15:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 25, Vehicles
using gaseous fuels.
ISO 12614 consists of the following parts, under the general title Road vehicles — Liquefied natural gas
(LNG) fuel system components:
— Part 1: General requirements and definitions
— Part 2: Performance and general test methods
— Part 3: Check valve
— Part 4: Manual valve
— Part 5: Tank pressure gauge
— Part 6: Overpressure regulator
— Part 7: Pressure relief valve
— Part 8: Excess flow valve
— Part 9: Gas-tight housing and ventilation hose
— Part 10: Rigid fuel line in stainless steel
— Part 11: Fittings
— Part 12: Rigid fuel line in material other than stainless steel
— Part 13: Pressure control regulator
— Part 14: Differential pressure fuel content gauge
— Part 15: Capacitance fuel content gauge
iv © ISO 2014 – All rights reserved

---------------------- Page: 4 ---
...

DRAFT INTERNATIONAL STANDARD ISO/DIS 12614-15
ISO/TC 22/SC 25 Secretariat: CUNA
Voting begins on Voting terminates on

2013-01-16 2013-04-16
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION  •  МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ  •  ORGANISATION INTERNATIONALE DE NORMALISATION


Road vehicles — Liquefied natural gas (LNG) fuel system
components —
Part 15:
Capacitance fuel content gauge
Véhicules routiers — Équipements pour véhicules utilisant le gaz naturel liquéfié (GNL) comme combustible —
Partie 15: Jauge de capacité
ICS 43.060.40









To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.



THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©  International Organization for Standardization, 2013

---------------------- Page: 1 ----------------------
ISO/DIS 12614-15

Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.

ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DIS 12614-15

Contents Page
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 Capacitance fuel content gauge . 2
3.2 Capacitance transmitter. 2
3.3 Fuel content indicator . 2
4 Marking . 2
5 Construction and assembly . 3
6 Test . 3
6.1 Applicability . 3
6.2 Insulation resistance . 4

© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/DIS 12614-15

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12614-15 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 25,
Vehicles using gaseous fuels.
ISO 12614 consists of the following parts, under the general title Road vehicles — Liquefied natural gas (LNG)
fuel system components:
— Part 1: General requirements and definitions
— Part 2: Performance and general test methods
— Part 3: Check valve
— Part 4: Manual valve
— Part 5: Tank pressure gauge
— Part 6: Overpressure regulator
— Part 7: Pressure relief valve
— Part 8: Excess flow valve
— Part 9: Gas-tight housing and ventilation hose
— Part 10: Rigid fuel line in stainless steel
— Part 11: Fittings
— Part 12: Rigid fuel line in copper and its alloys
— Part 13: Pressur
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.