ISO/FDIS 11759

Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) - Specification

Tuyaux et flexibles en caoutchouc destinés à la fourniture de gaz de pétrole liquéfiés (GPL) — Spécifications

General Information

• Status: Withdrawn
• ICS: 75.200 - Petroleum products and natural gas handling equipment
• ICS: 83.140.40 - Hoses
• Technical Committee: ISO/TC 45/SC 1 - Rubber and plastics hoses and hose assemblies
• Drafting Committee: ISO/TC 45/SC 1/WG 1 - Industrial, chemical and oil hoses
• Current Stage: 5098 - Project deleted
• Start Date: 26-Mar-2018
• Completion Date: 13-Dec-2025

Relations

• Replaces: ISO/FDIS 11759 - Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) - Specification
• Effective Date: 05-Nov-2015
• Revised: ISO 11759:1999 - Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) - Specification
• Effective Date: 04-Nov-2015

Standards Content (Sample)

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 11759
ISO/TC 45/SC 1
Rubber hoses and hose assemblies for
Secretariat: DSM
dispensing liquefied petroleum gases
Voting begins on:
2016­09­02 (LPGs) — Specification
Voting terminates on:
Tuyaux et flexibles en caoutchouc destinés à la fourniture de gaz de
2016­10­28
pétrole liquéfiés (GPL) — Spécifications
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2016

© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH­1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification . 2
5 Materials and construction . 2
6 Hydrostatic requirements . 2
7 Dimensions and tolerances . 2
8 Physical properties of materials . 3
9 Performance requirements for hoses and hose assemblies . 3
10 Frequency of testing . 4
11 Type tests . 4
12 Marking . 4
Annex A (normative) Flexibility test under reverse bending (flex test). 6
Annex B (normative) Test frequency. 8
Annex C (informative) Production tests . 9
Bibliography .10
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non­governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies.
This second edition cancels and replaces the first edition (ISO 11759:1999), which has been technically
revised with the following changes:
— Clause 2: ISO 1746 and ISO 4672 are deleted, and replaced with ISO 10619­1 and ISO 10619­2 and
inclusion of ISO 4671;
— Clause 4, Clause 5 and Table 4, addition of Type 3 for conductive hoses;
— Annex B on test frequency and Annex C on production test were added.
iv © ISO 2016 – All rights reserved

FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 11759:2016(E)
Rubber hoses and hose assemblies for dispensing liquefied
petroleum gases (LPGs) — Specification
WARNING — Persons using this document should be familiar with normal laboratory practice.
This document does not purport to address all of the safety problems, if any, associated with its
use. It is the responsibility of the user to establish appropriate safety and health practices and to
ensure compliance with any national regulatory conditions.
1 Scope
This document specifies the requirements for flexible rubber hoses and hose assemblies used for the
transfer of metered quantities of liquefied petroleum gases (LPGs) from dispensing equipment to motor
vehicles.
The hoses and hose assemblies specified in this document are intended for use “wet”, i.e. permanently
filled with liquid, in the temperature range from –40 °C to +60 °C.
The maximum working pressure is 2 MPa (20 bar).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances
on cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
ISO 4080, Rubber and plastics hoses and hose assemblies — Determination of permeability to gas
ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of
hoses and the lengths of hose assemblies
ISO 6801, Rubber or plastics hoses — Determination of volumetric expansion
ISO 7326, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
ISO 8031, Rubber and plastics hoses and hose assemblies — Determination of electrical resistance and
conductivity
ISO 8033, Rubber and plastics hoses — Determination of adhesion between components
ISO 10619­1, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 1:
Bending tests at ambient temperature
ISO 10619­2, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 2:
Bending tests at sub-ambient temperatures
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: availa
...