ISO 10468:2003/Amd 1:2010

Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor — Amendment 1

Tubes en plastiques thermodurcissables renforcés de verre (PRV) — Détermination de la rigidité annulaire spécifique à long terme en fluage en conditions mouillées et calcul du facteur de fluage mouillé — Amendement 1

General Information

• Status: Withdrawn
• Publication Date: 18-Aug-2010
• Withdrawal Date: 18-Aug-2010
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: ISO/TC 138/SC 6 - Reinforced plastics pipes and fittings for all applications
• Drafting Committee: ISO/TC 138/SC 6/WG 1 - Methods of test
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 03-May-2018

Relations

• Revised: ISO 10468:2018 - Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions
• Effective Date: 23-Apr-2016
• Amends: ISO 10468:2003 - Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
• Effective Date: 09-May-2020

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 10468
First edition
2003-12-01
AMENDMENT 1
2010-09-01

Glass-reinforced thermosetting plastics
(GRP) pipes — Determination of the long-
term specific ring creep stiffness under
wet conditions and calculation of the wet
creep factor

AMENDMENT 1
Tubes en plastiques thermodurcissables renforcés de verre (PRV) —
Détermination de la rigidité annulaire spécifique à long terme en fluage
en conditions mouillées et calcul du facteur de fluage mouillé

AMENDEMENT 1




Reference number
ISO 10468:2003/Amd.1:2010(E)
©
ISO 2010

---------------------- Page: 1 ----------------------
ISO 10468:2003/Amd.1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 10468:2003/Amd.1:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for
...