Plain bearings — Wrapped bushes — Part 2: Test data for outside and inside diameters

This document specifies the test data for outside and inside diameters of wrapped bushes made of mono and multi-layer bearing material for plain bearing applications. It also specifies test designations. Since the wall thickness of the bush is measured in the free condition, no special test data are required for this on the drawing (see ISO 3547‑5 and ISO 3547‑6). NOTE Depending on the manufacturing method, the back of the bushes can show isolated light depressions and, similarly, bushes with lubrication holes, grooves and bore indentations can show distortion. It is therefore suggested to measure the wall thickness away from these areas.

Paliers lisses — Bagues roulées — Partie 2: Données d'essai pour le diamètre extérieur et le diamètre intérieur

General Information

Status
Published
Publication Date
19-Jun-2023
Current Stage
6060 - International Standard published
Start Date
20-Jun-2023
Due Date
09-Jul-2024
Completion Date
20-Jun-2023
Ref Project

Relations

Buy Standard

Standard
ISO 3547-2:2023 - Plain bearings — Wrapped bushes — Part 2: Test data for outside and inside diameters Released:20. 06. 2023
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
REDLINE ISO/FDIS 3547-2 - Plain bearings — Wrapped bushes — Part 2: Test data for outside and inside diameters Released:1. 03. 2023
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 3547-2 - Plain bearings — Wrapped bushes — Part 2: Test data for outside and inside diameters Released:1. 03. 2023
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3547-2
Fourth edition
2023-06
Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside
diameters
Paliers lisses — Bagues roulées —
Partie 2: Données d'essai pour le diamètre extérieur et le diamètre
intérieur
Reference number
ISO 3547-2:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 3547-2:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
 © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3547-2:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units. 1
5 Presentation of data on drawing . 2
6 Tests . 3
6.1 Test A . 3
6.2 Test B . 3
6.3 Test C . 3
6.4 Test D . 4
7 Test A . 4
7.1 Description . 4
7.2 Calculation basis . 4
7.2.1 Elastic reduction, v, of outside diameter, D . 4
o
7.2.2 Calculation of diameter of checking block, d . 4
ch, 1
7.2.3 Effective cross-sectional area of the bush, A . 4
cal
7.2.4 Calculation of checking load, F . 5
ch
7.2.5 Limits for Δz . 6
7.3 Obtaining data — Example . . 6
7.4 Presentation of data on drawing — Example . 7
8 Test B . 7
8.1 Description . 7
8.2 Obtaining data — Example . 8
8.3 Presentation of data on drawing — Example . 8
9 Test C . 8
9.1 Description . 8
9.2 Obtaining data — Example . 9
9.3 Presentation of data on drawing — Example . 9
10 Test D .10
10.1 Description . 10
10.2 Obtaining data — Example . 10
10.3 Presentation of data on drawing — Example . 10
11 Designation of tests according to this document .11
Bibliography .12
iii
© ISO 2023 – All rights reserved

---------------------- Page: 3 ----------------------
ISO 3547-2:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This fourth edition cancels and replaces the third edition (ISO 3547-2:2017), of which it constitutes a
minor revision. The changes are as follows:
— the units in Table 1 have been corrected;
— in 7.2.3, the correct term for A has been implemented.
cal
A list of all the parts in the ISO 3547 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
 © ISO 2023 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3547-2:2023(E)
Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside diameters
1 Scope
This document specifies the test data for outside and inside diameters of wrapped bushes made of
mono and multi-layer bearing material for plain bearing applications. It also specifies test designations.
Since the wall thickness of the bush is measured in the free condition, no special test data are required
for this on the drawing (see ISO 3547-5 and ISO 3547-6).
NOTE Depending on the manufacturing method, the back of the bushes can show isolated light depressions
and, similarly, bushes with lubrication holes, grooves and bore indentations can show distortion. It is therefore
suggested to measure the wall thickness away from these areas.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 286-2, Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes —
Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
ISO 3547-1:2018, Plain bearings — Wrapped bushes — Part 1: Dimensions
ISO 3547-4, Plain bearings — Wrapped bushes — Part 4: Materials
ISO 4378-1, Plain bearings — Terms, definitions, classification and symbols — Part 1: Design, bearing
materials and their properties
ISO 4378-4, Plain bearings — Terms, definitions, classification and symbols — Part 4: Basic symbols
ISO 12301, Plain bearings — Quality control techniques and inspection of geometrical and material quality
characteristics
ISO 13715, Technical product documentation — Edges of undefined shape — Indication and dimensioning
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4378-1 and ISO 4378-4 apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www. iso. org/o bp
— IEC Elec
...

Error! Reference source not found.
Formatted: English (United Kingdom)
ISO/TC 123/SC 3
Date: 2023-02-27
ISO/FDIS 3457-2:2023
ISO/TC 123/SC 3/WG
Secretariat: DIN
Plain bearings — Wrapped bushes — Part 2: Test data for outside and inside
diameters
Paliers lisses — Bagues roulées — Partie 2: Données d'essai pour le diamètre
extérieur et le diamètre intérieur
Formatted: English (United Kingdom)
i Error! Reference source not found.

---------------------- Page: 1 ----------------------
ISO/FDIS 3547-2:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no
part of this publication may be reproduced or utilized otherwise in any form or by any means,
electronic or mechanical, including photocopying, or posting on the internet or an intranet, without
prior written permission. Permission can be requested from either ISO at the address below or
ISO's member body in the country of the requester.
ISO Copyright Office
CP 401 • CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Formatted: Normal
ii © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 3547-2:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directiveswww.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patentswww.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation onof the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL:
www.iso.org/iso/foreword.html), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This fourth edition cancels and replaces the third edition (ISO 3547-2:2017), which has been technically
revised.of which it constitutes a minor revision. The changes are as follows:
The main changes are as follows:
— — the units in table 1 hashave been corrected;
— In in clause 7.2.3, the correct term for A has been implemented.
cal

A list of all the parts in the ISO 3547 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

Formatted: Normal, Right
© ISO 2023 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3457-2:2017(E)
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 3547-2:2023(E)

Formatted: Header
Plain bearings — Wrapped bushes — Part 2: Test data for
outside and inside diameters
1 Scope
This document specifies the test data for outside and inside diameters of wrapped bushes made of mono
and multi-layer bearing material for plain bearing applications. It also specifies test designations.
Since the wall thickness of the bush is measured in the free condition, no special test data are required
for this on the drawing (see ISO 3547-5 and ISO 3547-6).
NOTE Depending on the manufacturing method, the back of the bushes can show isolated light depressions and,
similarly, bushes with lubrication holes, grooves and bore indentations can show distortion. It is therefore
suggested to measure the wall thickness away from these areas.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 286-2, Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes —
Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
1
ISO 3547-1:— :2018, Plain bearings — Wrapped bushes — Part 1: Dimensions
ISO 3547-4, Plain bearings — Wrapped bushes — Part 4: Materials
ISO 3547-5, Plain bearings — Wrapped bushes — Part 5: Checking the outside diameter
ISO 4378-1, Plain bearings — Terms, definitions, classification and symbols — Part 1: Design, bearing
materials and their properties
ISO 4378-4, Plain bearings — Terms, definitions, classification and symbols — Part 4: Basic symbols
ISO 12301, Plain bearings — Quality control techniques and inspection of geometrical and material quality
characteristics
ISO 13715, Technical drawings product documentation — Edges of undefined shape — Vocabulary —
Indication and indicationdimensioning

1
Under preparation. Stage at the time of publication: ISO/DIS 3547-1:2016.
© ISO 2017 2023 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO/FDIS 3547-2:2023(E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4378-1 and ISO 4378-4 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http://www.iso.org/obphttps://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/https://www.electropedia.org/
4 Symbols and units
See Table 1.
Table 1 — Symbols and units
Symbol Description Unit
2
A Reduced area of cross section (calculated value) of the bush mm
cal
B Width of the bush mm
C Inside chamfer mm
i
C Outside chamfer mm
o
Dfl Flange diameter mm
D Housing bore diameter mm
H
D Inside diameter of the bush mm
i
Di, ch Inside diameter of the bush in the ring gauge mm
D Outside diameter of the bush mm
o
F Checking load N
ch
dch, 1 Diameter of the checking block or ring gauge mm
d Diameter of the setting plug or plug gauge mm
ch, 2
r Flange radius mm
a
s1 Thickness of the backing layer mm
a
s Thickness of the bearing material layer mm
2
a
s Wall thickness mm
3
sfl Flange thickness mm
ΔD Tolerance of D mm
o o
v Elastic reduction of the outside diameter under checking load F mm
ch
z Distance apart of the halves of the checking block mm
Δz Indicator reading mm
Δz
Circumference indicator reading for test D mm
D
a
For bushes which are made of a single material, s1 = s3 or s2 = s3.
5 Presentation of data on drawing
The drawing should show either:
2 © ISO 2017 2023 – All rights reserved

---------------------- Page: 5 ----------------------
ISO 3457/FDIS 3547-2:20172023(E)
— the outside diameter, Do, and the wall thickness, s3, or;
— the outside diameter, Do, and the inside diameter, Di.
Wall thickness, s3, and inside diameter, Di, shall not be specified together on the same drawing. See
Figure 1.

a)  Type C cylindrical bush

b)  Type F flanged bush
© ISO 2017 2023 – All rights reserved 3

---------------------- Page: 6 ----------------------
ISO/FDIS 3547-2:2023(E)

a) Type C cylindrical bush

b) Type F flanged bush
Key
1 butt joint
a
Thickness of the bearing material layer: only valid as a basis for calculation in accordance with 7.2.
b
Ci may be a chamfer or break edge, in accordance with ISO 13715.
c
0,2 mm min. for nominal wall thickness 0,5 mm.
d
rmax = s3.
Figure 1 — Cylindrical and flanged bush taken from ISO 3547-1
4 © ISO 2017 2023 – All rights reserved

---------------------- Page: 7 ----------------------
ISO 3457/FDIS 3547-2:20172023(E)
6 Tests
6.1 Test A
Check the outside diameter, Do, using a checking block in a test rig and setting plug, in accordance with
Clause 7.
6.2 Test B
Check the outside diameter, D , using two ring gauges, in accordance with Clause 8.
o
6.3 Test C
Check the inside diameter, Di, of a bush pressed into a ring gauge, in accordance with Clause 9.
6.4 Test D
Check the outside diameter, D , using precision measuring tape, in accordance with Clause 10.
o
7 Test A
7.1 Description
This test is applicable to D up to 180 mm.
o
The test rig consists of a base on which the two parts of the checking block are mounted (see ISO 3547-5).
A setting plug is inserted in the checking block and the two halves of the checking block are pressed
towards one another using the given checking load, Fch, and the indicator reading set.
The setting plug is then removed and replaced by the bush to be checked, and the checking load reapplied.
After the bush has been inserted, the distance, z, between the two halves of the checking block changes
under checking load F and the distance indicator reading, Δz, is recorded.
ch
From this, D can be calculated.
o
Flanged bushes may be checked either before or after flange forming at the option of the manufacturer.
7.2 Calculation basis
7.2.1 Elastic reduction, v, of outside diameter, D
o
The elastic reduction, v, of the outside diameter, D , is the difference between D under zero load and the
o o
resultant diameter when the checking load, F , is applied. Force F shall be sufficient to ensure that the
ch ch
bush conforms properly to the surface of the test housing and that the results in the elastic reduction, v,
of the outside diameter are in accordance with Table 2.
Table 2 — Elastic reduction, v, of the outside diameter, D ,
o
under checking load, Fch
Dimensions in millimetres
D
o
v
nominal
 ≤ 6 0,003
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 3547-2
ISO/TC 123/SC 3
Plain bearings — Wrapped bushes —
Secretariat: DIN
Voting begins on:
Part 2:
2023-03-15
Test data for outside and inside
Voting terminates on:
diameters
2023-05-10
Paliers lisses — Bagues roulées —
Partie 2: Données d'essai pour le diamètre extérieur et le diamètre
intérieur
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 3547-2:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 1 ----------------------
ISO/FDIS 3547-2:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 3547-2
ISO/TC 123/SC 3
Plain bearings — Wrapped bushes —
Secretariat: DIN
Voting begins on:
Part 2:
Test data for outside and inside
Voting terminates on:
diameters
Paliers lisses — Bagues roulées —
Partie 2: Données d'essai pour le diamètre extérieur et le diamètre
intérieur
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: +41 22 749 01 11
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: copyright@iso.org
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 3547-2:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 2 ----------------------
ISO/FDIS 3547-2:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units. 1
5 Presentation of data on drawing . 2
6 Tests . 3
6.1 Test A . 3
6.2 Test B . 3
6.3 Test C . 3
6.4 Test D . 4
7 Test A . 4
7.1 Description . 4
7.2 Calculation basis . 4
7.2.1 Elastic reduction, v, of outside diameter, D . 4
o
7.2.2 Calculation of diameter of checking block, d . 4
ch, 1
7.2.3 Effective cross-sectional area, A . 4
cal
7.2.4 Calculation of checking load, F . 5
ch
7.2.5 Limits for Δz . 6
7.3 Obtaining data — Example . . 6
7.4 Presentation of data on drawing — Example . 7
8 Test B . 7
8.1 Description . 7
8.2 Obtaining data — Example . 8
8.3 Presentation of data on drawing — Example . 8
9 Test C . 8
9.1 Description . 8
9.2 Obtaining data — Example . 9
9.3 Presentation of data on drawing — Example . 9
10 Test D .10
10.1 Description . 10
10.2 Obtaining data — Example . 10
10.3 Presentation of data on drawing — Example . 10
11 Designation of tests according to this document .11
Bibliography .12
iii
© ISO 2023 – All rights reserved

---------------------- Page: 3 ----------------------
ISO/FDIS 3547-2:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This fourth edition cancels and replaces the third edition (ISO 3547-2:2017), of which it constitutes a
minor revision. The changes are as follows:
— the units in table 1 have been corrected;
— in clause 7.2.3, the correct term for A has been implemented.
cal
A list of all the parts in the ISO 3547 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2023 – All rights reserved

---------------------- Page: 4 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 3547-2:2023(E)
Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside diameters
1 Scope
This document specifies the test data for outside and inside diameters of wrapped bushes made of
mono and multi-layer bearing material for plain bearing applications. It also specifies test designations.
Since the wall thickness of the bush is measured in the free condition, no special test data are required
for this on the drawing (see ISO 3547-5 and ISO 3547-6).
NOTE Depending on the manufacturing method, the back of the bushes can show isolated light depressions
and, similarly, bushes with lubrication holes, grooves and bore indentations can show distortion. It is therefore
suggested to measure the wall thickness away from these areas.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 286-2, Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes —
Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
ISO 3547-1:2018, Plain bearings — Wrapped bushes — Part 1: Dimensions
ISO 3547-4, Plain bearings — Wrapped bushes — Part 4: Materials
ISO 4378-1, Plain bearings — Terms, definitions, classification and symbols — Part 1: Design, bearing
materials and their properties
ISO 4378-4, Plain bearings — Terms, definitions,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.