Cutter arbors with parallel key and tenon drive — Part 1: General dimensions

ISO 10649-1:2013 specifies the dimensions of tool interface for cutter arbors with parallel key and tenon drive.

Mandrins porte-fraise à entraînement par clavette et tenon — Partie 1: Dimensions générales

L'ISO 10649-1:2013 spécifie les dimensions des interfaces d'outil pour les mandrins porte-fraise à entraînement par clavette et tenon.

General Information

Status
Published
Publication Date
03-Nov-2013
Current Stage
9093 - International Standard confirmed
Completion Date
07-Mar-2019
Ref Project

Relations

Buy Standard

Standard
ISO 10649-1:2013 - Cutter arbors with parallel key and tenon drive
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 10649-1:2013 - Mandrins porte-fraise à entraînement par clavette et tenon
French language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 10649-1
Second edition
2013-10-15
Cutter arbors with parallel key and
tenon drive —
Part 1:
General dimensions
Mandrins porte-fraise à entraînement par clavette et tenon —
Partie 1: Dimensions générales
Reference number
ISO 10649-1:2013(E)
ISO 2013
---------------------- Page: 1 ----------------------
ISO 10649-1:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 10649-1:2013(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Dimensions ................................................................................................................................................................................................................. 1

3.1 General ........................................................................................................................................................................................................... 1

3.2 Dimensions of tool interface for arbors with parallel key and tenon drive ........................................ 1

Annex A (informative) Relationship between the symbols of this part of ISO 10649 and the

ISO 13399 series ................................................................................................................................................................................................... 4

Bibliography ................................................................................................................................................................................................................................ 5

© ISO 2013 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 10649-1:2013(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received. www.iso.org/patents

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, High speed

steel cutting tools and their attachments.

This second edition cancels and replaces the first edition (ISO 10649-1:2010), of which it constitutes a

minor revision with the following changes:

— addition of Annex A, which gives the relationship between the symbols of this part of ISO 10649 and

...

NORME ISO
INTERNATIONALE 10649-1
Deuxième édition
2013-10-15
Mandrins porte-fraise à entraînement
par clavette et tenon —
Partie 1:
Dimensions générales
Cutter arbors with parallel key and tenon drive —
Part 1: General dimensions
Numéro de référence
ISO 10649-1:2013(F)
ISO 2013
---------------------- Page: 1 ----------------------
ISO 10649-1:2013(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2013

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée

sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur

l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à

l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2013 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 10649-1:2013(F)
Sommaire Page

Avant-propos ..............................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Domaine d’application ................................................................................................................................................................................... 1

2 Références normatives ................................................................................................................................................................................... 1

3 Dimensions ................................................................................................................................................................................................................. 1

3.1 Généralités .................................................................................................................................................................................................. 1

3.2 Dimensions des interfaces d’outils pour les mandrins porte-fraise à entraînement par

clavette et tenon ..................................................................................................................................................................................... 1

Annexe A (informative) Relation entre les désignations de la présente partie de l’ISO 10649 et

celles de l’ISO 13399 ......................................................................................................................................................................................... 4

Bibliographie .............................................................................................................................................................................................................................. 5

© ISO 2013 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 10649-1:2013(F)
Avant-propos

L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes

nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est

en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.

L’ISO collabore étroitement avec la Commission électrotechnique internationale (CEI) en ce qui concerne

la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/CEI, Partie 1. Il convient, en particulier de prendre note des différents

critères d’approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/CEI, Partie 2, www.iso.

org/directives.

L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de

droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les

références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l’élaboration

du document sont indiqués dans l’Introduction et/ou sur la liste ISO des déclarations de brevets reçues,

www.iso.org/patents.

Les éventuelles appellations commerciales utilisées dans le présent document sont données pour

information à l’intention des utilisateurs et ne constituent pas une approbation ou une recommandation.

Le comité chargé de l’élaboration du présent document est l’ISO/TC 29, Petit outillage, sous-comité SC 2,

Outils coupants en acier rapide et leurs attachements.

Cette deuxième édition annule et remplace la première édition (ISO 10649-1:2010), dont elle constitue

une révision mineure. Elle inclut les changements suivants:
— ajout d
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.