ISO 9415:1989

Woodworking machines — Wide belt sanding machines — Nomenclature

Specifies the nomenclature appopriate to the various parts of these wide belt sanding machines in order to assist manufacturers and users in the identification of these parts. Gives in addition to terms used in two of the three official ISO languages (English and French) the equivalent terms in the German, Spanish and Italian languages.

Machines à bois — Ponceuces à bande large — Nomenclature

General Information

• Status: Withdrawn
• Publication Date: 17-May-1989
• Withdrawal Date: 17-May-1989
• ICS: 01.040.79 - Wood technology (Vocabularies)
• ICS: 79.120.10 - Woodworking machines
• Technical Committee: ISO/TC 39/SC 4 - Woodworking machines
• Drafting Committee: ISO/TC 39/SC 4 - Woodworking machines
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 20-Jun-2016

Standards Content (Sample)

IS0 9415 : 1989 (E/F)
Foreword
IS0 (the International Organization for Standardization) is a worldwide federation of
national standards bodies (IS0 member bodies). The work of preparing International
Standards is normally carried out through IS0 technical committees. Each member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. international organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the IS0 Council. They are approved in accordance with IS0 procedures requiring at
least 75 % approval by the member bodies voting.
International Standard IS0 9415 was prepared by Technical Committee ISO/TC 39,
Machine tools.
Annex A of this International Standard is for information only.
0 IS0 1989
All rights reserved. No part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in
writing from the publisher./Droits de reproduction reserves. Aucune partie de cette publication
ne peut etre reproduite ni utilisee sous quelque forme que ce soit et par aucun procede, electroni-
que ou mecanique, y compris la photocopie et les microfilms, sans I’accord ecrit de I’editeur.
International Organization for Standardization
l CH-1211 Geneve 20 l Switzerland
Case postale 56
Printed in Switzerland/ Imprime en Suisse
ii

---------------------- Page: 1 ----------------------
IS0 9415 : 1989 (E/F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une federation mondiale
d’organismes nationaux de normalisation (comites membres de 1’60). L’elaboration
des Normes internationales est en general confide aux comites techniques de I’ISO.
Chaque comite membre interesse par une etude a le droit de faire partie du comite
technique tree a cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec I’ISO participent egalement aux travaux. L’ISO col-
labore etroitement avec la Commission electrotechnique internationale KEI) en ce qui
concerne la normalisation Blectrotechnique.
Les projets de Normes internationales adopt& par les comites techniques sont soumis
aux comites membres pour approbation, avant leur acceptation comme Normes inter-
nationales par le Conseil de I’ISO. Les Normes internationales sont approuvees confor-
mement aux procedures de I’ISO qui requierent I’approbation de 75 % au moins des
comites membres votants.
La Norme internationale IS0 9415 a et6 elaboree par le comite technique ISO/TC 39,
Machines-outils.
L’annexe A de la presente Norme internationale est donnee uniquement a titre d’infor-
mation.
. . .
III

---------------------- Page: 2 ----------------------
This page intentionally left blank

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD
IS0 9415 : 1989 (E/F)
NORME INTERNATIONALE
Machines ti bois -
Woodworking machines -
Ponceuses 8 bande large -
Wide belt sanding
Nomenclature
Nomenclature
machines -
1 Domaine d’application
1 Scope
La presente Norme internationale indique la nomenclature
This International Standard specifies the nomenclature appro-
propre aux differentes parties des ponceuses a bande large,
priate to the various parts of wide belt sanding machines in
order to assist manufacturers and users in the identification of afin d’aider les constructeurs et les utilisateurs dans I’identifica-
tion de ces parties.
these parts.
NOTE - En complement des termes utilises dans deux des trois
NOTE - In addition to terms used in two of the three official IS0
languages (English and French), this International Standard gives the langues officielles de I’ISO (anglais et francais), cette Norme internatio-
nale donne les termes equivalents dans les langues allemande, espa-
equivalent terms in the German, Spanish and Italian languages; these
are published under the responsibility of the member bodies for gnole et italienne ; ces termes sont publies sous la responsabilite des
comites membres de I’Allemagne, R.F. (DIN), de I’Espagne (AENOR)
Germany, F.R. (DIN), Spain (AENOR) and Italy (UNI). However, only
the terms given in the official languages can be considered as IS0 et de I’ltalie (UNI). Toutefois, seuls les termes don& dans les langues
officielles peuvent etre consider& comme etant des termes de I’ISO.
terms.
This International Standard applies to those machines desig- La presente Norme internationale s’applique aux machines
nated by the number 12.722 in IS0 7984’). designees sous le numero 12.722 de I’ISO 7984’).
1) IS0 7984 : 1988, Woodworking machines - Technical classifi- S 1) IS0 7984 : 1988, Machines ;i bois - Classification technique des
cation of woodworking machines and auxiliary machines for wood- machines ;i travailler le bois et des machines auxiliaires 8 travaiiler /e
bois.
working.
1

---------------------- Page: 4 ----------------------
IS0 9415 : 1989 (E/F)
2 Nomenclature
2 51 . 81 . 66 . 6.5 5.2 7.1
7,
5
. 8
41 .
26 .
33 .
32 .
73 .
2

---------------------- Page: 5 ----------------------
IS0 9415 : 1989 (E/F)
French
English
teference
Francais
Anglais
Rep&e
Ponceuses 6 bande large
Wide belt sanding machines
Ossature
1 Framework
Bati
1.1 Body
Deplacement des pieces et/au outils
Feed of workpiece and/or tools
2
Reducteur de vitesse
2.1 Speed reduction box
Variateur de vitesse
2.2 Variable-speed drive
Courroie de transmission
Drive belt
2.3
Tapis d’amenage
2.4 Feed conveyor belt
Rouleau d’entrainement du tapis d’amenage
Feed conveyor drive roller
2.5
Rouleau fou du tapis d’amenage
2.6 Feed conveyor idle roller
Support,
...