Rubber, raw natural and raw synthetic — Sampling and further preparative procedures

ISO 1795:2017 specifies a method for the sampling of raw rubber in bales, blocks or packages and further procedures carried out on the samples to prepare test samples for chemical and physical tests.

Caoutchouc, naturel brut et synthétique brut — Méthodes d'échantillonnage et de préparation ultérieure

L'ISO 1795:2017 spécifie une méthode d'échantillonnage du caoutchouc brut en balles, blocs ou paquets, et les modes opératoires ultérieurs appliqués à ces échantillons en vue de préparer des prises d'essais pour les essais chimiques et physiques.

General Information

Status
Published
Publication Date
25-Jun-2017
Current Stage
9093 - International Standard confirmed
Completion Date
01-Jul-2022
Ref Project

Relations

Buy Standard

Standard
ISO 1795:2017 - Rubber, raw natural and raw synthetic -- Sampling and further preparative procedures
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 1795:2017 - Caoutchouc, naturel brut et synthétique brut -- Méthodes d'échantillonnage et de préparation ultérieure
French language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 1795
Fifth edition
2017-06
Rubber, raw natural and raw
synthetic — Sampling and further
preparative procedures
Caoutchouc, naturel brut et synthétique brut — Méthodes
d’échantillonnage et de préparation ultérieure
Reference number
ISO 1795:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 1795:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 1795:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Method of selecting the sample. 2
5 Method of taking the laboratory sample . 2
6 Testing . 2
7 Preparation of test samples . 3
7.1 General . 3
7.2 Natural rubber . 3
7.2.1 Homogenizing . 3
7.2.2 Chemical and physical tests . 3
7.2.3 Mooney viscosity . 3
7.2.4 Plasticity retention index (PRI) . 3
7.2.5 Vulcanization characteristics . 3
7.3 Synthetic rubbers . 3
7.3.1 Chemical and physical tests . 3
7.3.2 Mooney viscosity . 4
7.3.3 Vulcanization characteristics . 5
8 Sampling report. 5
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 1795:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry.
This fifth edition cancels and replaces the fourth edition (ISO 1795:2007), which has been technically
revised. The main changes compared to the previous edition are as follows:
— the normative references in Clause 2 have been updated;
— in Clause 4, it has been clarified that the number of bales to be chosen at random represent the lot;
— in Clause 5, the note stating that the surface layer may be removed if it is contaminated with talc or
a release agent, has been deleted;
— the title of 7.2.1 has been changed from “milling” to “homogenizing”;
— in 7.3.1, a sentence has been added to specify to take directly the test samples from the laboratory
sample when using thermogravimetric methods in ISO 248-2 for the determination of volatile-
matter content.
iv © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 1795:2017(E)
Rubber, raw natural and raw synthetic — Sampling and
further preparative procedures
WARNING — Persons using this document should be familiar with normal laboratory practice.
This document does not purport to address all of the safety problems, if any, associated with its
use. It is the responsibility of the user to establish appropriate safety and health practices and to
ensure compliance with any national regulatory conditions.
1 Scope
This document specifies a method for the sampling of raw rubber in bales, blocks or packages and
further procedures carried out on the samples to prepare test samples for chemical and physical tests.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 248-1, Rubber, raw — Determination of volatile-matter content — Part 1: Hot-mill method and
oven method
ISO 248-2, Rubber, raw — Determination of volatile-matter content — Part 2: Thermogravimetric methods
using an automatic analyser with an infrared drying unit
ISO 289-1, Rubber, unvulcanized — Determinations using a shearing-disc viscometer — Part 1:
Determination of Mooney viscosity
ISO 1658, Natural rubber (NR) — Evaluation procedure
ISO 2393, Rubber test mixes — Preparation, mixing and vulcanization — Equipment and procedures
ISO 2930, Rubber, raw natural — Determination of plasticity retention index (PRI)
ISO 3951-2, Sampling procedures for inspection by variables — Part 2: General specification for single
sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality
characteristics
ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test methods
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available
...

NORME ISO
INTERNATIONALE 1795
Cinquième édition
2017-06
Caoutchouc, naturel brut et
synthétique brut — Méthodes
d’échantillonnage et de préparation
ultérieure
Rubber, raw natural and raw synthetic — Sampling and further
preparative procedures
Numéro de référence
ISO 1795:2017(F)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 1795:2017(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 1795:2017(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Méthode de sélection de l’échantillon . 2
5 Méthode de prélèvement de l’échantillon de laboratoire . 2
6 Essais . 3
7 Préparation des prises d’essai . 3
7.1 Généralités . 3
7.2 Caoutchouc naturel . 3
7.2.1 Homogénéisation . 3
7.2.2 Essais chimiques et physiques . 3
7.2.3 Viscosité Mooney . 3
7.2.4 Indice de rétention de plasticité (PRI) . 3
7.2.5 Caractéristiques de vulcanisation . 4
7.3 Caoutchoucs synthétiques . 4
7.3.1 Essais chimiques et physiques . 4
7.3.2 Viscosité Mooney . 4
7.3.3 Caractéristiques de vulcanisation . 5
8 Rapport d’échantillonnage . 5
© ISO 2017 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 1795:2017(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion
de l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: w w w . i s o .org/ iso/ fr/ avant -propos .html
Le présent document a été élaboré par le comité technique ISO/TC 45, Élastomères et produits à base
d’élastomères, sous-comité SC 3, Matières premières (y compris le latex) à l’usage de l’industrie des
élastomères.
Cette cinquième édition annule et remplace la quatrième édition (ISO 1795:2007), qui a fait l’objet d’une
révision technique. Les principales modifications par rapport à la précédente édition sont les suivantes:
— les références normative à l’Article 2 ont été mises à jour;
— à l’Article 4, il a été précisé que le nombre de balles à choisir de façon aléatoire représente le lot;
— à l’Article 5, la note indiquant que la couche superficielle peut être enlevée si elle est contaminée par
du talc ou un agent anticollant, a été supprimée;
— le titre de 7.2.1 a été modifié de «passage au mélangeur à cylindres» en «homogénéisation»;
— en 7.3.1, une phrase a été ajoutée pour spécifier de prélever directement les prises d’essais sur
l’échantillon de laboratoire lorsque les méthodes thermogravimétriques de l’ISO 248-2 sont utilisées
pour la détermination de la teneur en matières volatiles.
iv © ISO 2017 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 1795:2017(F)
Caoutchouc, naturel brut et synthétique brut — Méthodes
d’échantillonnage et de préparation ultérieure
AVERTISSEMENT — Il convient que l’utilisateur du présent document connaisse bien les
pratiques courantes de laboratoire. Le présent document n’a pas pour but de traiter tous les
problèmes de sécurité qui sont, le cas échéant, liés à son utilisation. Il incombe à l’utilisateur
d’établir des pratiques appropriées en matière d’hygiène et de sécurité, et de s’assurer de la
conformité à la réglementation nationale en vigueur.
1 Domaine d’application
Le présent document spécifie une méthode d’échantillonnage du caoutchouc brut en balles, blocs ou
paquets, et les modes opératoires ultérieurs appliqués à ces échantillons en vue de préparer des prises
d’essais pour les essais chimiques et physiques.
2 Références normatives
Les documents suivants cités dans le texte constituent, pour tout ou partie de leur contenu, des
exigences du présent document. Pour les références datées, seule l’édition citée s’applique. Pour les
références non datées, la dernière édition du document de référence s’applique (y compris les éventuels
amendements).
ISO 248-1, Caoutchouc brut — Détermination des matières volatiles — Partie 1: Méthode par mélangeage
à chaud et méthode par étuvage
ISO 248-2, Caoutchouc brut — Détermination des matières volatiles — Partie 2: Méthodes
thermogravimétriques utilisant un analyseur automatique avec une unité de séchage infrarouge
ISO 289-1, Caoutchouc non vulcanisé — Déterminations utilisant un consistomètre à disque de
cisaillement — Partie 1: Détermination de l’indice consistométrique Mooney
ISO 1658, Caoutchouc naturel (NR) — Méthode d’évaluation
ISO 2393, Mélanges d’essais à base de caoutchouc — Mélangeage, préparation et vulcanisation —
Appareillage et modes opératoires
ISO 2930, Caoutchouc naturel brut — Détermination de l’indice de rétention de plasticité (PRI)
ISO 3951-2, Règles d’échantillonnage pour les contrôles par mesures — Partie 2: Spécification générale pour
les plans d’échantillonnage simples indexés d’après une limite de qualité acceptable (LQA) pour le contrôle
lot par lot de caractéristiques-qualité indépendantes
ISO 23529, Caoutchouc — Procédures générales pour la préparation et le conditionnement des éprouvettes
pour les méthodes d’essais physiques
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions suivants s’appliquent.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes:
— IEC Electropedia: disponible à l’adresse http:// www .electropedia .org/
— ISO Online browsing platform: disponible à l’adresse http:// www .iso .org/ obp
© ISO 2017 – Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 1795:2017(F)

NOTE Toutes références à des “balles” incluent les blocs et les paquets de caoutchouc sous forme de copeaux,
poudre ou feuilles.
3.1
lot
ensemble de balles de caoutchouc de même grade et portant les mêmes marques de lot
3.2
échantillon
groupe de balles choisies pour représenter le lot
3.3
échantillon de laboratoire
caoutchouc prél
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.