ISO 6916-2:2001

Flexible cellular polymeric materials — Sponge and expanded cellular rubber products — Specification — Part 2: Mouldings and extrusions

This part of ISO 6916 classifies flexible cellular rubber products known as sponge and expanded rubber. The base material used in their manufacture may be natural rubber, reclaimed rubber, synthetic rubber or rubber-like material, either alone or in combination. Thermoplastic rubbers are not included. This part of ISO 6916 does not apply to latex foam rubbers or shoe soling. Sheeting materials are covered by ISO 6916-1. This part (part 2) covers vulcanized cellular rubber products that are manufactured by a moulding or continuous vulcanization process, i.e. hot air, microwave, infra-red, liquid curing medium (LCM), shearing-head vulcanization or a combination of two or more of these methods. In the case of conflict between the provisions of this part of ISO 6916 and those of the detailed specification or test method for a particular product, the latter shall take precedence. Reference to the methods shall specifically state the desired test or tests.

Polymères alvéolaires souples — Caoutchoucs alvéolaires mousses et souples — Spécification — Partie 2: Moulage et extrusion

General Information

• Status: Withdrawn
• Publication Date: 19-Dec-2001
• ICS: 83.100 - Cellular materials
• Technical Committee: ISO/TC 45/SC 4 - Products (other than hoses)
• Drafting Committee: ISO/TC 45/SC 4 - Products (other than hoses)
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 26-Apr-2024

Relations

• Consolidated By: ISO 1461:1999 - Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
• Effective Date: 06-Jun-2022
• Revised: ISO 6916-2:2024 - Flexible cellular polymeric materials — Sponge and expanded cellular rubber products — Part 2: Specification for mouldings and extrusions
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6916-2
First edition
2001-12-15

Flexible cellular polymeric materials —
Sponge and expanded cellular rubber
products — Specification —
Part 2:
Mouldings and extrusions
Polymères alvéolaires souples — Caoutchoucs alvéolaires mousses et
souples — Spécification —
Partie 2: Moulage et extrusion




Reference number
ISO 6916-2:2001(E)
©
 ISO 2001

---------------------- Page: 1 ----------------------
ISO 6916-2:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland

ii © ISO 2001 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6916-2:2001(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references.1
3 Classification (types, classes, grades and suffixes) .2
4 Material and workmanship .3
5 Physical properties.3
6 Methods of test .3
7 Dimensional tolerances .3
8 Inspection and rejection .3
9 Packaging and marking .4
10 Sampling.4
11 Standard test pieces, standard test sheets and specially prepared extruded shapes .4
12 Measurement of test piece dimensions .5
Annex A (normative) Heat-resistance test.13
Annex B (normative) Compression deflection tests .14
Annex C (normative) Oil resistance test.15
Annex D (normative) Compression set under constant deflection .16
Annex E (normative) Water absorption test.17
Annex F (normative) Fluid resistance test .18
Annex G (normative) Low-temperature resistance test .
...