ISO 15569:1998
(Main)Practice for dosimetry in an electron-beam facility for radiation processing at energies between 300 keV and 25 MeV
Practice for dosimetry in an electron-beam facility for radiation processing at energies between 300 keV and 25 MeV
Pratique de la dosimétrie utilisant des faisceaux d'énergie comprise entre 300 keV et 25 MeV
General Information
Relations
Standards Content (Sample)
IS0
INTERNATIONAL
15569
STANDARD
First edition
19984245
Practice for dosimetry in an electron-beam
facility for radiation processing at energies
between 300 keV and 25 MeV
Pratique de la dosim&e utill ’sant des faisceaux d ’hergie comprise entre
300keVet25MeV
Reference number
IS0 15569: 1998(E)
---------------------- Page: 1 ----------------------
IS0 15569:1998(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies
(IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
re circul ated to the member bodi es for votin .
Draft International Standards adopted by the technical committees a
g
Publication as an lnternationa I Standard requires approval by at least 75 % of the me mber bodies casti a vote.
4
International Standard IS0 15569 was prepared by the American Society for Testing and Materials (ASTM)
Subcommittee E1O.O1 (as E 1649-94) and was adopted, under a special “fast-track procedure ”, by Technical
Committee lSO/TC 85, Nuclear energy, in parallel with its approval by the IS0 member bodies.
A new lSO/TC 85 Working Group WG 3, High-level dosimetry for radiation processing, was formed to review the
voting comments from the IS0 “Fast-track procedure” and to maintain these standards. The USA holds the
convenership of this working group.
International Standard IS0 15569 is one of 20 standards developed and published by ASTM. The 20 fast-tracked
standards and their associated ASTM designations are listed below:
IS0 Designation ASTM Designation Title
E 1204-93 Practice for dosimetry in gamma irradiation facilities for food
15554
processing
E 1205-93 Practice for use of a ceric-cerous sulfate dosimetry system
15555
15556 E 1261-94 Guide for selection and calibration of dosimetry systems for
radiation processing
15557 E 1275-93 Practice for use of a radiochromic film dosimetry system
E 1276-96 Practice for use of a polymethylmethacrylate dosimetry system
15558
15559 E 1310-94 Practice for use of a radiochromic optical waveguide dosimetry
sys tern
E 1400-95a Practice for characterization and performance of a high-dose
15560
radiation dosime try calibra Con labora tory
E 1401-96 Practice for use of a dichromate dosimetry system
15561
0 IS0 1998
All rights reserved. Unless otherwise specified, no pa .rt of this publication may be reproduced or utilized in any form or by any means, electronic
mechanical, including photocopying and mic rofilm, without permission in writing from the publisher.
or
International Organization for Standardization
Case postale 56 l CH-1211 Geneve 20 l Switzerland
Internet iso @ isoch
Printed in Switzerland
ii
---------------------- Page: 2 ----------------------
IS0 15569:1998(E)
@ IS0
15562 E 1431-91 Practice for dosimetry in electron and bremsstrahlung irradiation
facilities for food processing
15563 E 1538-93 Practice for use of the ethanol-chlorobenzene dosimetry system
15564 E 1539-93 Guide for use of radiation-sensitive indicators
E 1540-93
15565 Practice for use of a radiochromic liquid dosimetry system
15566 E 1607-94 Practice for use of the alanine-EPR dosimetry system
Practice for dosimetry in an X-ray (bremsstrahlung) facility for
15567 E 1608-94
radiation processing
Practice for use of calorimetric dosimetry systems for electron
15568 E 1631-96
beam dose measurements and dosimeter calibrations
Practice for dosimetty in an electron-beam facility for radiation
15569 E 1649-94
processing at energies between 300 keV and 25 MeV
15570 E 1650-94 Practice for use of cellulose acetate dosimetry system
15571 E 1702-95 Practice for dosimetry in a gamma irradiation facility for radiation
processing
15572 E 1707-95 Guide for estimating uncertainties in dosimetry for radiation
processing
E 1818-96 Practice for dosimetry in an electron-beam facility for radiation
15573
processing at energies between 80 keV and 300 keV
For the purposes of this International Standard, the following amendments to the ASTM text apply.
Page 1, subclause 1.2, note 2, and subclause 1.3
Replace note 2 and subclause 1.3 by the following.
1.3 Dosimetry is only one component of a total quality assurance program for an irradiation facility. Other
controls besides dosimetry may be required for specific applications such as medical device sterilization and
food preservation.
I .4 For the irradiation of food and the radiation sterilization of health care products, other specific IS0
standards exist. For food irradiation, see IS0 15562:1998, Practice for dosimetry in electron and
bremsstrahlung irradiation facilities for food processing (ASTM Practice E 1431). For the radiation sterilization
of health care products, see IS0 11137:1995, Sterilization of health care products - Requirements for
validation and routine control - Radiation sterilization. In those areas covered by IS0 11137, that standard
takes precedence.
Page I, subclause 1.4
Renumber this subclause as 1.5.
. . .
Ill
---------------------- Page: 3 ----------------------
0 IS0 IS0 15569: 1998(E)
AMERICAN SOCIETY FOR TESJlNG AND MATERIALS
Designation: E 1649 - 94
1916 Race St Philadelphia, Pa 19103
Reprinted from the Annual Book of ASTM Standards. Copyright ASTM
If not listed in the current combined index, will appear in the next edition.
Standard Practice for
Dosimetry in an Electron Beam Facility for Radiation
Processing at Energies Between 300 keV and 25 IVleV’
This standard is issued under the fixed designation E 1649; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (c) indicates an editorial change since the last revision or reapproval.
Absorbed Dose in Radiation-Hardness Testing of Elec-
1. Scope
tronic Devices2
1.1 This practice covers dosimetric procedures to be
E 1026 Practice for Using the Fricke Reference Standard
followed in facility characterization, process qualification,
Dosimetry System2
and routine processing using electron beam radiation to
E 1205 Practice for Use of a Ceric-Cerous Sulfate
ensure that the entire product has been treated with an
Dosimetry System2
acceptable range of absorbed doses. Other procedures related
E 126 1 Guide for Selection and Calibration of Dosimetry
to facility characterization (including equipment documen-
Systems for Radiation Processing2
tation), process qualification, and routine product processing
E 1275 Practice for Use of a Radiochromic Film
that may influence and may be used to monitor absorbed
Dosimetry System2
dose in the product are also discussed.
E 1276 Practice for Use of a Polymethylmethacrylate
NOTE I-For guidance in the selection and calibration of dosimeters,
Dosimetry System2
see Guide E 126 I. For further guidance in the selection, calibration, and
E 140 1 Practice for Use of a Dichromate Dosimetry
use of specific dosimeters, and interpretation of absorbed dose in the
System2
product from dosimetry, also see Practices E 668, E 1275, E 1276,
E 143 1 Practice for Dosimetry in Electron and Brems-
E 143 1, E 1607, E 163 1, and E 1650. For use with electron energies
above 5 MeV, see Practices E 1026, E 1205, E 1401, E 1538, and E 1540
strahlung Irradiation Facilities for Food Processing2
for discussions of specific large volume dosimeters. For discussion of
E
1538 Practice for Use of an Ethanol-Chlorobenzene
radiation dosimetry for pulsed radiation, see ICRU Report 34. When
Dosimetry System2.
considering a dosimeter type, be cautious of influences from dose rates
E 1539 Guide for the Use of Radiation-Sensitive Indi-
and accelerator pulse rates and widths (if applicable).
cators2
1.2 The electron energy range covered in this practice is
E 1540 Practice for Use of a Radiochromic Liquid Solu-
between 300 keV and 25 MeV, although there are some
tion Dosimetry System2
discussions for other energies.
E 1607 Practice for Use of the Alanine-EPR Dosimetry
NOTE 2-For application of dosimetry in the characterization and System2
operation of electron beam and X-ray (bremsstrahlung) irradiation E 1608 Practice for Dosimetry in an X-Ray (Brems-
facilities for food processing, see Practice E 143 1. For application of
strahlung) Irradiation Facility for Radiation Processing2
dosimetry in the characterization and operation of irradiation facilities
E 163 1 Practice for Use of Calorimetric Dosimetry Sys-
using X-ray radiation (bremsstrahlung), see Practice E 1608.
tems for Electron Beam Measurements and Dosimeter
1.3 Dosimetry is one component of a total quality assur-
Calibrations2
ance program for adherence to good manufacturing prac-
E
1650 Practice for Use of a Cellulose Acetate Dosimetry
tices. Specific applications of electron beam radiation pro-
System2
cessing may require additional controls.
2.2 International Commission on Radiation Units and
1.4 This standard does not purport to address all of the
Measurements (ICR V” Reports:
safety concerns, ZJ! any, associated with its use. It is the
ICRU Report 33 Radiation Quantities and Units3
responsibility of the user of this standard to establish appro-
ICRU Report 34 The Dosimetry of Pulsed Radiation3
priate safety and health practices and determine the applica-
ICRU Report 35 Radiation Dosimetry: Electron Beams
bility of regulatory limitations prior to use.
with Energies Between 1 and 50 MeV3
ICRU Report 37 Stopping Powers for Electrons and
2. Referenced Documents
Positrons3
2.1 ASTM Standards:
E 170 Terminology Relating to Radiation Measurements 3. Terminology
and Dosimetry2
3.1 Definitions -Other terms used in this practice may be
E 668 Practice for the Application of Thermolumi-
found in Terminology E 170 and ICRU Report 33.
nescence-Dosimetry (TLD) Systems for Determining
3.2 Descriptions of Terms Speci$c to This Standard.
3.2.1 absorbed dose, D-the quotient of dZ by dm, where
d? is the mean energy imparted by ionizing radiation to the
I This practice is under the jurisdiction of ASTM Committee E-IO on Nuclear
Technology and Applications and is the direct responsibility of Subcommittee
E1O.O1 on Dosimetry for Radiation Processing.
3 Available from International Commission on Radiation Units and Measurc-
Current edition approved Nov. i 5, 1994. Published February 1995.
mcnts, 79 10 Woodmont Ave., Suite 800, Bcthcsda, MD 208 14.
2 Anntrui Book o/ASTM S~~r~hrds, Vol 12.02.
I
---------------------- Page: 4 ----------------------
@ IS0
IS0 15569:1998(E)
beam current; for a puked machine, the averaging shalE be
done over a large number of pulses.
3.2,3 beam length--dimension of the irradiation zone
perpendicular to the beam width and direction of the
electron beam specified at a specified distance from the
accelerator window.
DscusstoN-See Fig. 1 0
3.2.4 beam power-product of the average electron en-
ergy and the average beam current.
3.2.5 beam width-dimension of the irradiation zone
perpendicular to the beam length and direction of the
electron beam specified at a specific distance from where the
beam exits the accelerator.
~lscussroN--For a radiation processing facility with a conveyor
system, the beam width is usually perpendicular to the flow of motion of
the conveyor (see Fig. 1). Beam width is the distance between the points
CONVEYOR-
along the dose profile which are at a defined level from the maximum
dose region in the profile (see Fig. 2). Various techniques may be
LENGTH
employed to produce an electron beam width adequate to cover the
FIG. 1 Diagram Showing Beam Length and Width for a Scanned processing zone, for example, use of electromagnetic scanning of pencil
Beam Using a Conveyor Material Handling System
beam (in which case beam width is also referred to as scan width),
defocussing elements, and scattering foils.
3.2.6 compensating dummy-simulated product used
matter of mass dm (see ICRU Report 33).
L
during routine production runs with irradiation units con-
de
=-
D
taining less product than specified in the product loading
dm
configuration or at the beginning and end of a production
The special name of the unit for absorbed dose is the gray
run to compensate for the absence of product.
(GYh 3.2.7 depth-dose distribution-variation of absorbed dose
with depth from the incident surface of a material exposed to
1 Gy = 1 J-kg-’
radiation.
Formerly, the special unit for absorbed dose was the rad:
DISCUWON-A typical distribution in homogeneous material pro-
1 rad = 1O-2 Jekg-’ = 1O-2 Gy
duced by an electron beam along the beam axis is shown in Fig. 3. See
and:
1 Mrad = 10 kGy
4 McKeown, J., AECL Accelerators, private communication, 1993. Example of
a beam width profile of an AECL lmpela accelerator.
beam current-time-averaged electron
3.2.2 average
0.16
0.15
-0
0.14 max
- fD
0.13 max
0.12
0.11
s 0.1
(3
s 0.09
W
g 0.08
0 0.07
0.06
0.05
0.04
0.03
0.02
0.01
I 1 1 I 1 I I 1 I 1
0
-50 -30 -10 10 30 50
DISTANCE (cm)
FIG. 2 Example of Electron-beam Dose Distribution Along the Beam Width4 with the Width Noted at Some Defined Fractional Level f of
the Average Maximum Dose D,,,
2
---------------------- Page: 5 ----------------------
IS0 15569:1998(E)
at the surface where the electron beam enters.
DIscussloN-See Fig. 3.
3.2.19 practical range @,)-distance from the surface of
8
De homogeneous material where the electron beam enters to the
ii
point where the tangent at the steepest point (the inflection
8
point) on the almost straight descending portion of the
depth-dose distribution curve meets the depth axis.
DrscussIoN-See Fig. 3.
3.2.20 production run- series of irradiation units con-
taining the same product, and irradiated sequentially to the
same absorbed dose.
FQopt R50 40, Rp 3.2.21 pulse beam current -for a pulsed accelerator, the
beam current averaged over the top ripples (aberrations) of
DEPTH (ARBITRAFIY UNfTS)
the pulse current waveform; this is equal to &/wl; where
Iavs is the average beam current, w is the pulse width, andfis
FIG. 3 A Typical Depth-Dose Distribution for an Electron Beam
the pulse rate.
Appendix X 1.
DIscussrON-See Fig. 4.
3.2.8 dose unz@mity ratio-ratio of the maximum to the
3.2.22 pulse rate-for a pulsed accelerator, the pulse
minimum absorbed dose within the irradiation unit; it is a
current repetition frequency in hertz, or pulses per second;
measure of the degree of uniformity of the absorbed dose; the
concept is also referred to as the max/min dose ratio. this is also referred to as the repetition (rep) rate.
3.2.23 pulse width-for a pulsed accelerator, the time
3.2.9 dosimetry system- a system used for determining
interval between the half peak beam current amplitude
absorbed dose, consisting of dosimeters, measurement in-
points on the leading and falling edges of the pulse beam
struments and their associated reference standards, and
procedures for the system ’s use. current waveform.
3.2.10 duty cycle-for a pulsed accelerator, the fraction of
DrscussloN-See Fig. 4,
time the beam is effectively on; it is the product of the pulse
width in seconds and the pulse rate in pulses per second.
3.2.24 reference material-homogeneous material of
3.2.11 electron beam facility-an establishment that uses
known radiation absorption and scattering properties used to
energetic electrons produced by particle accelerators to
establish characteristics of the irradiation process, such as
irradiate product.
scan uniformity, depth-dose distribution, throughput rate,
3.2.12 electron energy-kinetic energy of electron (unit:
and reproducibility.
electron volt (eV))
3.2.25 refirence plane-a selected plane in the radiation
3.2.13 electron energy spectrum-frequency or energy
zone that is perpendicular to the electron beam axis.
distribution of electrons as a function of energy; the energy
3.2.26 scanned beam-an electron beam which is swept
spectrum of the electron beam impinging on the product
back and forth with a varying magnetic field.
depends on the type of the accelerator and the conditions of
the irradiation process.
DIscussroN-This is most commonly done along one dimension
3.2.14 electron range-penetration distance along the
(beam width), although two dimensional scanning (beam width and
beam axis of electrons within homogeneous material. length) may be used with high-current electron beams to avoid
overheating the beam exit window of the accelerator.
DrsCus%ON-Several range parameters may be defined to describe
the characteristics of the electron beam. For more information, refer to
ICRU Report 35.
~ PULSE ~
I
WIDTH
3.2.15 hapentrance depth (R&-depth in homogeneous
I
I
material at which the absorbed dose has decreased 50 % of
the absorbed dose at the surface of the material.
DrscussroN-See Fig. 3.
3.2.16 ha@alue depth &J--depth in homogeneous
material at which the absorbed dose has decreased 50 % of its
maximum value.
DISCussloN-See Fig. 3.
3.2.17 irradiation unit-a volume of product with a
specified loading configuration processed as a single entity;
TlME
this term is not relevant to bulk-flow processing.
3.2.18 optimum thickness (R&-depth in homogeneous
FIG. 4 Typical Pulse Current Waveform with Pulse Current and
Pulse Width Noted
material at which the absorbed dose equals the absorbed dose
3
---------------------- Page: 6 ----------------------
IS0 15569:1998(E) @ IS0
4.5 Before a radiation process can be used, the facility
3.2.27 scan unijbrmity-the degree of uniformity of the
must be qualified to demonstrate its ability to deliver known,
dose measured along the scan direction.
controllable doses in a reproducible manner. This involves
3.2.28 simulated product-a mass of material with atten-
uation and scattering properties similar to those of a partic- testing the process equipment, calibrating the equipment and
ular material or combination of materials; this material is dosimetry system, and characterizing the magnitude, distri-
sometimes referred to as dummy product or phantom. bution, and reproducibility of the dose absorbed by a
.
reference material.
4. Significance and Use
4.6 To ensure that products are irradiated with reproduc-
ible doses, routine process control requires hocumented
4.1 Various products and materials are routinely irradi-
product handling procedures before, during, and after the
ated at pre-determined doses at electron beam facilities to
irradiation, consistent orientation of the products during
preserve or modify their characteristics. Dosimetry require-
irradiation, monitoring of critical process parameters, rou-
ments may vary depending upon the radiation process and
tine product dosimetry, and documentation of the required
end use of the product. For example, a partial list of
activities and functions.
processes where dosimetry may be used is:
4.1.1 Cross-linking or degradation of polymers and
5. Radiation Source Characteristics
elastomers,
4.1.2 Polymerization of monomers and grafting of mono-
5.1 Radiation sources for electrons with energies greater
mers onto polymers,
than 300 keV considered in this practice are either direct-
4.1.3 Sterilization of medical devices,
action (potential-drop) or indirect-action (microwave-
4.1.4 Disinfection of consumer products,
powered) accelerators. These are further discussed in Ap-
4.1.5 Food irradiation (parasite and pathogen control,
pendix X2.
insect disinfestation, and shelf-life extension),
4.1.6 Control of pathogens in liquid or solid waste,
6. Types of Irradiation Facility
4.1.7 Modification of characteristics of semiconductor
6.1 An electron beam facility includes the electron beam
devices,
accelerator system; material handling systems; a radiation
4.1.8 Color enhancement of gemstones and other mate-
shield with personnel safety system; product staging, loading,
rials, and
and storage areas; auxiliary equipment for power, cooling,
4.1.9 Research on materials effects.
ventilation, etc.; equipment control room; a laboratory for
NOTE 3-Dosimetry is required for regulated radiation processes
dosimetry and product testing; and personnel ofices. The
such as the sterilization of medical devices (I,%, 3)s and the preservation
electron beam accelerator system consists of the radiation
of food. It may be less important for other processes, such as polymer
source (see Appendix X2), equipment to disperse the beam
modification, which may be evaluated by changes in the physical and
on product, and associated equipment (4).
chemical properties of the irradiated materials. Nevertheless, routine
6.2 Process Parameters:
dosimetry may be used to monitor the reproducibility of the treatment
6.2.1 There are various process parameters that play
process.
essential roles in determining and controlling the absorbed
4.2 As a means of (quality) control of the radiation
dose in radiation processing at an irradiation facility. They
process, dosimeters are used to relate the calibrated response
should, therefore, be considered when performing the ab-
to radiation to the absorbed dose in the material or product
sorbed-dose measurements required in Sections 8, 9, and 10.
being irradiated.
6.2.2 Process parameters include irradiation unit charac-
NOTE 4-Measured dose is often characterized as absorbed dose in
teristics (for example, size, bulk density, and heterogeneity),
water because materials commonly found in disposable medical devices
irradiation conditions (for example, processing geometry,
and food are approximately equivalent to water in the absorption of
multi-sided exposure, and number of passes through the
ionizing radiation. Absorbed dose in materials other than water may be
beam), and operating parameters.
determined by applying conversion factors in accordance with Guide
6.2.3 Operating parameters include beam characteristics
E 1261.
(controlled by accelerator parameters: for example, energy,
4.3 A beneficial irradiation process is usually specified by
average beam current, and pulse rate), performance charac-
a minimum absorbed dose to achieve the desired effect and a
teristics of material handling (see 6.3), and beam dispersion
maximum dose limit that the product can tolerate and still
parameters (for example, beam width and frequency at
be functional. Since it is used to determine these limits,
which scanned beam is swept across product). Operating
dosimetry is essential in the evaluation and control of the
parameters are measurable, and their values depend on the
radiation process.
facility controlling parameters. During irradiation facility
4.4 The dose distribution within the product depends on
qualification (see Section 8), absorbed dose characteristics
irradiation unit characteristics, irradiation conditions, and
over the expected range of the operating parameters are
operating parameters. The operating parameters consist of
established for a reference material.
beam characteristics (such as energy and beam current),
6.2.4 Process parameters for a radiation process are estab-
beam dispersion parameters, and product material handling,
lished during process qualification (see Section 9) to achieve
These critical parameters must be controlled to obtain
the absorbed dose within the specified limits.
reproducible results.
6.2.5 During routine product processing (see Section lo),
the facility operating parameters are controlled and moni-
tored to maintain all values that were set during process
3 The boldface numbers in parentheses refer to a list of references at the end of
this practice. qualification.
4
---------------------- Page: 7 ----------------------
0 IS0
IS0 15569:1998(E)
operating within specified limits, will consistently produce an
6.2.6 Different product types may require different oper-
absorbed-dose distribution in a given product to prerequisite
ating and process parameters.
6.3 Configuration of A4ateriaI Handling-The absorbed specification. Such documentation shall be retained for the
dose distributions within product may be affected by the life of the irradiator, and include: -
8.2.1 The irradiator specifications and characteristics,
material handling system. Examples of systems commonly
8.2.2 A description of the location of the irradiator within
used are:
6.3.1 Conveyors or Carriers-Material is placed upon the operator ’s premises in relation to the means ’provided for
carriers or conveyors for passage through the electron beam. the segregation of non-irradiated products from irradiated
The speed of the conveyor or carriers is controlled in products, if required,
conjunction with the electron beam current and beam width 8.2.3 A description of the construction and the operation
so that the required dose is applied. of any associated material handling equipment,
8.2.4 The dimensions and the description of the materials
6.3.2 Roll-to-Roil Feed System-Roll-to-roll (also referred
to as reel-to-reel) feed systems are used for tubing, wire, and the construction of containers used to hold products
during irradiation, if used,
cable, and continuous web products. The speed of the system
is controlled in conjunction with the electron beam current 8.2.5 A description of the manner of operating the irradi-
and beam width so that the required dose is applied. ator, and
6.3.3 Bulk-flow System- For irradiation of liquids or 8.2.6 Any modifications made during and after installa-
particulate materials like grain or plastic pellets, bulk-flow tion.
transport through the irradiation zone may be used. Because 8.3 Equipment Testing and Calibration-The absorbed
the flow velocity of the individual pieces of the product dose within an irradiation unit depends in part on the
cannot be controlled, the average velocity of the product in operating parameters: beam characteristics, material han-
dling, beam dispersion parameters, and their inter-relation-
conjunction with the beam characteristics and beam disper-
sion parameters determines the average absorbed dose. ships. It also depends on irradiation unit characteristics and
6.3.4 Stationary-For high dose processes, the material irradiation conditions. These operating parameters are con-
may be placed under the beam and not moved. Cooling may trolled by various accelerator and other facility parameters.
be required to dissipate the heat accumulated by the product 8.3.1 Beam Characteristics:
8.3.1.1 The three principal beam characteristics that affect
during processing. The amount of irradiation time is con-
trolled in conjunction with the electron beam current, beam dosimetry are the electron energy spectrum, average beam
length, and beam width to achieve the required dose. current, and pulse beam current. The electron energy spec-
trum affects the depth-dose distribution within the product
7. Dosimetry Systems (see Appendix Xl). The average and pulse beam currents, in
addition to several other operating parameters, affect the
7.1 Dosimetry systems are used to determine absorbed
average and peak dose rates, respectively.
dose and consist of the dosimeter, the calibration curve or
function, reference standards, appropriate instrumentation,
NOTE S-Indirect-action (microwave-powered) accelerators may de-
and procedures for the system ’s use.
liver higher dose rates while the beam current is actually on compared to
direct-action (potential-drop) accelerators with the same average beam
7.2 It is important that the dosimeter be evaluated for
current. These higher dose rates in a pulsed mode may affect the
those parameters which may influence the dosimeter ’s re-
dosimeter response.
sponse; for example, electron energy, average and peak
NOTE 6-The electron energy spectrum of the accelerated electron
absorbed dose rate (particularly for pulsed accelerators), and
beam may be characterized by the average electron energy (E,) and the
environmental conditions (for example, temperature, hu-
most probable electron energy (E,) (see Appendix X3). An energy
midity, and light). Guidance as to desirable characteristics
analyzing magnet may be used for more detailed analysis.
and selection criteria for dosimetry systems can be found in
8.3.2 Material Handling:
Guide E 126 1, Practices E 1026, E 1205, E 1275, E 1276,
8.3.2.1 For facilities utilizing continuously-moving con-
E 1401, E 1538, E 1540, E 1607, E 1631, and E 1650.
veyors (including, for example, roll-to-roll feed systems for
7.3 The dosimetry system should be properly calibrated
tubing, wire, cable, and continuous web products) to trans-
using a calibration service traceable to national standards.
port product through the irradiation zone, conveyor speed
Guidance for calibration can be found in Guide E 126 1.
determines the irradiation time. Therefore, when other
operating parameters are held constant, conveyor speed
8. Irradiation Facility Qualification
governs the absorbed dose in the product.
8.1 Objeclive-The purpose of qualifying an electron
NOTE 7-The conveyor speed and the beam current may be linked
beam facility is to establish baseline data for evaluating the
for some types of accelerators so that a variation in one causes a
ability of the facility to accurately and reproducibly deliver
corresponding change in the oth
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.