ISO 3852:2007

Iron ores for blast furnace and direct reduction feedstocks — Determination of bulk density

ISO 3852:2007 specifies two methods of determining the bulk density of iron ores. Method 1 is applicable to natural iron ore and processed iron ore having a nominal top size of 40 mm. Method 2 is applicable to any natural iron ores and processed ores, regardless of size.

Minerais de fer pour charges de hauts fourneaux et pour procédés par réduction directe — Détermination de la masse volumique apparente

General Information

• Status: Published
• Publication Date: 22-Aug-2007
• ICS: 73.060.10 - Iron ores
• Technical Committee: ISO/TC 102/SC 3 - Physical testing
• Drafting Committee: ISO/TC 102/SC 3 - Physical testing
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 19-Oct-2022

Relations

• Revises: ISO 3852:1988 - Iron ores — Determination of bulk density
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3852
Third edition
2007-09-01
Iron ores for blast furnace and direct
reduction feedstocks — Determination of
bulk density
Minerais de fer pour charges de hauts fourneaux et pour procédés par
réduction directe — Détermination de la masse volumique apparente

Reference number
ISO 3852:2007(E)
©
ISO 2007

---------------------- Page: 1 ----------------------
ISO 3852:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
©
ii ISO 2007 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3852:2007(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Sampling, sample preparation and preparation of test portions . 2
6 Apparatus . 2
7 Procedure . 3
8 Expression of results . 3
9 Test report . 4
10 Verification . 4
Annex A (normative) Flowsheet of the procedure for the acceptance of test results . 6
©
ISO 2007 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3852:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3852 was prepared by Technical Committee ISO/TC 102, Iron ore and direct reduced iron, Subcommittee
SC 3, Physical testing.
This third edition cancels and replaces the second edition (ISO 3852:1988), which has been revised to
homogenise with other physical test standards.
©
iv ISO 2007 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 3852:2007(E)
Introduction
This is one of a number of physical test methods that have been developed to measure various physical
parameters and to evaluate the behaviour of iron ores including reducibility, disintegration, crushing strength,
apparent density, etc. This method was developed to provide a uniform procedure, validated by collaborative
testing, to facilitate comparisons of tests made in different laboratories.
The results of this test should be considered in conjunction with other tests used to evaluate the quality of iron
ores as feedstocks for blast furnace and direct reduction processes.
This International Standard may be used to provide test results as part of a production quality-control system,
as a basis of a contract, or as part of a research project.
©
ISO 2007 – All rights reserved v

---------------------- Page: 5 ----------------------
.
vi

---------------------- Page: 6 ----------------------
INTERNATIONAL STANDARD ISO 3852:2007(E)
Iron ores for blast furnace and direct reduction feedstocks —
Determination of bulk density
CAUTION—This International Standard may involve hazardous operations and equipment. This
International Standard does not purport to address all of the safety issues associated with its use. It is
the responsibility of the user of this International Standard to establish appropriate safety and health
practices and to determine the applicability of regulatory limitations prior to its use.
1Scope
This International Standard specifies two methods of determining the bulk density of iron ores.
Method 1 is applicable to natural iron ore and processed iron ore having a nominal top size of 40 mm.
Method 2 is applicable to any natural iron ores and processed ores, regardless of size.
NOTE The measured density does not necessarily represent the bulk density of compacted or stockpiled iron ores.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
1)
ISO 3082:2000, Iron ores — Sampling and sample preparation procedures
ISO 3087:1998, Iron ores — Determination of moisture content of a lot
2)
ISO 4701:— , Iron ores and direct reduced iron — Determination of size distribution by sieving
ISO 11323:2002, Iron ore and direct reduced iron — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 11323 apply.
4 Principle
A test portion is introduced into a container of known volume until its surface is level. The bulk density is
calculated as the ratio of the mass of the sample to the internal volume of the container.
1) Under revision to i
...