Graphical symbols — Safety colours and safety signs — Registered safety signs — Amendment 7

Symboles graphiques — Couleurs de sécurité et signaux de sécurité — Signaux de sécurité enregistrés — Amendement 7

General Information

Status
Not Published
Current Stage
6000 - International Standard under publication
Completion Date
07-Jun-2023
Ref Project

Relations

Buy Standard

Draft
REDLINE ISO 7010:2019/PRF Amd 7 - Graphical symbols — Safety colours and safety signs — Registered safety signs — Amendment 7 Released:10. 05. 2023
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO 7010:2019/PRF Amd 7 - Graphical symbols — Safety colours and safety signs — Registered safety signs — Amendment 7 Released:10. 05. 2023
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

ISO /TC 145/SC 2
Date: 2023-04
ISO 7010:2019/PRF Amd 7:2023(E)
ISO/TC 145/SC 2/WG 1
Secretariat: DIN
Date: 2023-05-09
Graphical symbols — Safety colours and safety signs —
— Registered safety signs — Amendment
AMENDMENT 7

Symboles graphiques — Couleurs de sécurité et signaux de sécurité — Signaux de sécurité enregistrés —

Amendement 7
AMENDEMENT 7
FDIS stage
© ISO 2023 – All rights reserved
---------------------- Page: 1 ----------------------
ISO 7010:2019/PRF Amd 7(E)
© ISO 20232019

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this

publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,

including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can

be requested from either ISO at the address below or ISO'sISO’s member body in the country of the requester.

ISO Copyright Officecopyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Email: E-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland.
ii © ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7010:2019/PRF Amd 7(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO

collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documentsdocument should be noted. This document was drafted in accordance

with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawnISO draws attention to the possibility that some of the elementsimplementation of this

document may beinvolve the subjectuse of (a) patent(s). ISO takes no position concerning the evidence,

validity or applicability of any claimed patent rights in respect thereof. As of the date of publication of

this document, ISO had not received notice of (a) patent(s) which may be required to implement this

document. However, implementers are cautioned that this may not represent the latest information,

which may be obtained from the patent database available at www.iso.org/patents.. ISO shall not be held

responsible for identifying any or all such patent rights. Details of any patent rights identified during the

development of the document will be in the Introduction and/or on the ISO list of patent declarations

received (see ).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the World

Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see

www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 145, Graphical symbols, Subcommittee

SC 2, Safety identification, signs, shapes, symbols and colours.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www.iso.org/members.html.
© ISO 202
...

INTERNATIONAL ISO
STANDARD 7010
Third edition
2019-07
AMENDMENT 7
Graphical symbols — Safety colours
and safety signs — Registered safety
signs
AMENDMENT 7
Symboles graphiques — Couleurs de sécurité et signaux de sécurité —
Signaux de sécurité enregistrés
AMENDEMENT 7
PROOF/ÉPREUVE
Reference number
ISO 7010:2019/Amd.7:2023(E)
© ISO 2023
---------------------- Page: 1 ----------------------
ISO 7010:2019/Amd.7:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on

the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below

or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE © ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7010:2019/Amd.7:2023(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO document should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

ISO draws attention to the possibility that the implementation of this document may involve the use

of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed

patent rights in respect thereof. As of the date of publication of this document, ISO had not received

notice of (a) patent(s) which may be required to implement this document. However, implementers are

cautioned that this may not represent the latest information, which may be obtained from the patent

database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all

such patent rights.

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to

the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see

www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 145, Graphical symbols, Subcommittee

SC 2, Safety identification, signs, shapes, symbols and colours.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www.iso.org/members.html.
iii
© ISO 2023 – All rights reserved PROOF/ÉPREUVE
---------------------- Page: 3 ----------------------
ISO 7010:2019/Amd.7:2023(E)
Grap
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.