ISO 13609:2014
(Main)Wood-based panels — Plywood — Blockboards and battenboards
Wood-based panels — Plywood — Blockboards and battenboards
ISO 13609:2014 establishes requirements for the specifications of blockboards and battenboards for general use, in dry, tropic dry/humid, and high-humid/exterior conditions. It includes requirements of materials, lay-up, physical and mechanical properties, bonding quality, formaldehyde release, conformity verification, and marking. The values listed in ISO 13609:2014 relate to product properties, but they are not characteristic values to be used in design calculations.
Panneaux à base de bois — Contreplaqués — Panneaux lattés avec lattes étroites et avec lattes larges
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 13609
First edition
2014-02-01
Wood-based panels — Plywood —
Blockboards and battenboards
Panneaux à base de bois — Contreplaqués — Panneaux lattés avec
lattes étroites et avec lattes larges
Reference number
ISO 13609:2014(E)
©
ISO 2014
---------------------- Page: 1 ----------------------
ISO 13609:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 13609:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Material requirement . 2
4.1 Requirements for veneer. 2
4.2 Requirements for plywood . 2
4.3 Requirements for core strip. 3
4.4 Requirements for core strip assembly . 4
4.5 Adhesives . 4
5 Panel lay-up and manufacturing requirements . 4
6 General requirements . 4
6.1 Dimensions and tolerances . 4
6.2 Classification by surface appearance . 4
6.3 Requirements of physical and mechanical properties. 5
7 Bonding quality . 5
8 Formaldehyde release requirements . 5
9 Other characteristics . 5
10 Conformances . 5
11 Marking, identification, and documentation . 6
© ISO 2014 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 13609:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 89, Wood-based panels, Subcommittee SC 3,
Plywood.
iv © ISO 2014 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 13609:2014(E)
Wood-based panels — Plywood — Blockboards and
battenboards
1 Scope
This International Standard establishes requirements for the specifications of blockboards and
battenboards for general use, in dry, tropic dry/humid, and high-humid/exterior conditions. It includes
requirements of materials, lay-up, physical and mechanical properties, bonding quality, formaldehyde
release, conformity verification, and marking.
The values listed in this International Standard relate to product properties, but they are not
characteristic values to be used in design calculations.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO/IEC Guide 65, General requirements for bodies operating product certification systems
ISO/IEC 17065, Conformity assessment— Requirements for bodies certifying products, processes and
services
ISO 1954, Plywood — Tolerances on dimensions
ISO 2074, Plywood — Vocabulary
ISO 2426-2, Plywood — Classification by surface appearance — Part 2: Hardwood
ISO 2426-3, Plywood — Classification by surface appearance — Part 3: Softwood
ISO 9426, Wood-based panels — Determination of dimensions of panels
ISO 12460-1, Wood-based panels — Determination of formaldehyde release — Part 1: Formaldehyde
emission by the 1-cubic-metre chamber method
ISO 12460-3, Wood-based panels — Determination of formaldehyde release — Part 3: Gas analysis method
ISO 12460-4, Wood-based panels — Determination of formaldehyde release — Part 4: Desiccator method
ISO 12465, Plywood — Specifications
ISO 12466-1, Plywood — Bonding quality — Part 1: Test methods
ISO 12466-2, Plywood — Bonding quality — Part 2: Requirements
ISO 16978, Wood-based panels — Determination of modulus of elasticity in bending and of bending strength
ISO 16979, Wood-based panels — Determination of moisture content
ISO 16999, Wood-based panels — Sampling and cutting of test pieces
ISO 18775, Veneers — Terms and definitions, determination of physical characteristics and tolerances
© ISO 2014 – All rights reserved 1
---------------------- Page: 5 ----------------------
ISO 13609:2014(E)
3 Terms and definitions
For the purposes of this document, the terms and definitions in ISO 2074, ISO 12465, and ISO 18775 a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.