ISO/IEC 14443-3:2011/Amd 2:2012

Identification cards — Contactless integrated circuit cards — Proximity cards — Part 3: Initialization and anticollision — Amendment 2: Bit rates of fc/8, fc/4 and fc/2, frame size from 512 bytes to 4 096 bytes and minimum TR0

Cartes d'identification — Cartes à circuit(s) intégré(s) sans contact — Cartes de proximité — Partie 3: Initialisation et anticollision — Amendement 2: Débits binaires de fc/8, fc/4 et fc/2, taille de trame comprise entre 512 octets et 4 096 octect et TR0 minimal

General Information

• Status: Withdrawn
• Publication Date: 11-Sep-2012
• Withdrawal Date: 11-Sep-2012
• ICS: 35.240.15 - Identification cards. Chip cards. Biometrics
• Technical Committee: ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification
• Drafting Committee: ISO/IEC JTC 1/SC 17/WG 8 - Integrated circuit cards without contacts
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 27-May-2016

Relations

• Revised: ISO/IEC 14443-3:2016 - Identification cards — Contactless integrated circuit cards — Proximity cards — Part 3: Initialization and anticollision
• Effective Date: 21-Nov-2015
• Amends: ISO/IEC 14443-3:2011 - Identification cards — Contactless integrated circuit cards — Proximity cards — Part 3: Initialization and anticollision
• Effective Date: 27-Nov-2021

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 14443-3
Second edition
2011-04-15
AMENDMENT 2
2012-09-15

Identification cards — Contactless
integrated circuit cards — Proximity
cards —
Part 3:
Initialization and anticollision
AMENDMENT 2: Bit rates of fc/8, fc/4
and fc/2, frame size from 512 bytes to
4 096 bytes and minimum TR0
Cartes d´identification — Cartes à circuit(s) intégré(s) sans contact —
Cartes de proximité —
Partie 3: Initialisation et anticollision
AMENDEMENT 2: Débits binaires de fc/8, fc/4 et fc/2, taille de trame
comprise entre 512 octets et 4 096 octects et TR0 minimal




Reference number
ISO/IEC 14443-3:2011/Amd.2:2012(E)
©
ISO/IEC 2012

---------------------- Page: 1 ----------------------
ISO/IEC 14443-3:2011/Amd.2:2012(E)

COPYRIGHT PROTECTED DOCUMENT


©  ISO/IEC 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 14443-3:2011/Amd.2:2012(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
Amendment 2 to ISO/IEC 14443-3:2011 was prepared by Joint Technical Committee ISO/IEC JTC 1,
Information technology, Subcommittee SC 17, Cards and personal identification.
© ISO/IEC 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 14443-3:2011/Amd.2:2012(E)

Identification cards — Contactless integrated circuit cards —
Proximity cards —
Part 3:
Initialization and anticollision
AMENDMENT 2: Bit rates of fc/8, fc/4 and fc/2, frame size from
512 bytes to 4 096 bytes and minimum TR0
Pages 5–6, 6.1
Replace the subclause with the following:
“
6.1 etu
The value of the etu for each bit rate is defined in Table 1.
Table 1 — etu
Bit rates etu
fc/128 128/fc
(~ 106 kbit/s) (~ 9,4 µs)
fc/64 128/2fc
(~ 212 kbit/s) (~ 4,7 µs)
fc/32 128/4fc
(~ 424 kbit/s) (~ 2,4 µs)
fc/16 128/8fc
(~ 848 kbit/s) (~ 1,2 µs)
fc/8 128/16fc
(~ 1,70 Mbit/s) (~ 0,59 µs)
fc/4 128/32fc
(~ 3,39 Mbit/s) (~0,29 µs)
fc/2 128/64fc
(~ 6,78 Mbit/s) (~0,15 µs)

”

© ISO/IEC 2012 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO/IEC 14443-3:2011/Amd.2:2012(E)
Page 6, 6.2.1.1
Add the following after the first paragraph:
“For bit rates of fc/8, fc/4 and fc/2 the FDT starts at the end of the last modulation transmitted by the PCD.”

Page 7, 6.2.1.1
Replace the title of Figure 1 with the following:
“Figure 1 — Frame delay time PCD to PICC for bit rates up to fc/16”
Replace the row before the last row of Table 2 with the following:
“
fc/128 or fc/64 or fc/64 or fc/32 or fc/16 Not applicable
 1116/fc  1116/fc
fc/32 or fc/16 or fc/8 or fc/8 or fc/4 or fc/2
or fc/4 or fc/2

”
Add the following after Table 2:
“
NOTE If a bit rate higher than fc/16 is selected for PCD to PICC communication, then a bit rate of fc/128 is not
allowed for PICC to PCD communication, see ISO/IEC 14443-4:2008/Amd.2. This restriction is required because the
necessary precise FDT is not defined for PCD NRZ coding which is used for bit rates higher than fc/16.
The FDT measurement starts at the beginning of the rising edge as specified and illustrated with small circles
in the following figures of ISO/IEC 14443-2:
 Figure 3 for bit rate of fc/128,
 Figure 6 for bit rates of fc/64, fc/32 and fc/16,
 Figure 12 for bit rates of fc/8, fc/4 and fc/2.
”

Page 7, 6.2.1.2
Replace the word “pause” by “modulation”.

Page 8, 6.2.3
Add the following after the last dash:
“
 PCD standard frames for bit rates of fc/8, fc/4 and fc/2.
”
2 © ISO/IEC 2012 – All rights reserved

---------------------- Page: 5 ----------------------
ISO/IEC 14443-3:2011/Amd.2:2012(E)
Pages 8–9, 6.2.3.2
Add the following new subclause:
“6.2.3.2.1 PCD standard frame for bit rates of fc/128, fc/64, fc/32 and fc/16 and PICC standard frame”

Move the text of 6.2.3.2 into this subclause.

Replace:
“The PCD standard frame is illustrated in Figure 3.”
with:
“The PCD standard frame for bit rates of fc/128, fc/64, fc/32 and fc/16 is illustrated in Figure 3.”

Replace Figure 3 title with:
“Figure 3 — PCD standard frame for
...