iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 13373-10

(Main)

Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 10: Diagnostic techniques for electrical generators with fluid film bearings

Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 10: Diagnostic techniques for electrical generators with fluid film bearings

Surveillance et diagnostic d'état des machines — Surveillance des vibrations — Partie 10: Techniques de diagnostic pour les générateurs électriques de puissance à paliers à film fluide

General Information

Status
Not Published
ICS
17.160 - Vibrations, shock and vibration measurements
Technical Committee
ISO/TC 108/SC 2 - Measurement and evaluation of mechanical vibration and shock as applied to machines, vehicles and structures
Drafting Committee
ISO/TC 108/SC 2 - Measurement and evaluation of mechanical vibration and shock as applied to machines, vehicles and structures
Current Stage
6000 - International Standard under publication
Completion Date
04-Jun-2024
Ref Project

Buy Standard

ISO/FDIS 13373-10 - Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 10: Diagnostic techniques for electrical generators with fluid film bearings Released:25. 03. 2024ISO/FDIS 13373-10 - Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 10: Diagnostic techniques for electrical generators with fluid film bearings Released:25. 03. 2024
PreviousNext
Draft
ISO/FDIS 13373-10 - Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 10: Diagnostic techniques for electrical generators with fluid film bearings Released:25. 03. 2024
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ISO/FDIS 13373-10 - Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 10: Diagnostic techniques for electrical generators with fluid film bearings Released:25. 03. 2024REDLINE ISO/FDIS 13373-10 - Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 10: Diagnostic techniques for electrical generators with fluid film bearings Released:25. 03. 2024
PreviousNext
Draft
REDLINE ISO/FDIS 13373-10 - Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 10: Diagnostic techniques for electrical generators with fluid film bearings Released:25. 03. 2024
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

FINAL DRAFT
International
Standard
ISO/FDIS 13373-10
ISO/TC 108/SC 2
Condition monitoring and
Secretariat: DIN
diagnostics of machines —
Voting begins on:
Vibration condition monitoring —
2024-04-08
Part 10:
Voting terminates on:
2024-06-03
Diagnostic techniques for electrical
generators with fluid film bearings
Surveillance et diagnostic d'état des machines - Surveillance des
vibrations —
Partie 10: Techniques de diagnostic pour les générateurs
électriques de puissance de sortie supérieure à 50 MVA
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 13373-10:2024(en) © ISO 2024

---------------------- Page: 1 ----------------------
FINAL DRAFT
ISO/FDIS 13373-10:2024(en)
International
Standard
ISO/FDIS 13373-10
ISO/TC 108/SC 2
Condition monitoring and
Secretariat: DIN
diagnostics of machines —
Voting begins on:
Vibration condition monitoring —
Part 10:
Voting terminates on:
Diagnostic techniques for electrical
generators with fluid film bearings
Surveillance et diagnostic d'état des machines - Surveillance des
vibrations —
Partie 10: Techniques de diagnostic pour les générateurs
électriques de puissance de sortie supérieure à 50 MVA
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
COPYRIGHT PROTECTED DOCUMENT
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2024
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 13373-10:2024(en) © ISO 2024

© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO/FDIS 13373-10:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Measurements . 2
4.1 Vibration measurements .2
4.2 Machine operational parameter measurement .2
5 Initial analysis . 2
6 Specific analys
...

Style Definition
...
Style Definition
...
Style Definition
...
ISO/FDIS 13373-10:2024(en)
Style Definition
...
ISO /TC 108/SC 2/WG 10
Style Definition
...
Style Definition
Secretariat: DIN .
Style Definition
...
Date: 2024-03-07xx
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
Condition monitoring and diagnostics of machines — Vibration
...
Style Definition
condition monitoring — .
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Part 10:
Style Definition
...
Diagnostic techniques for electrical generators with fluid film
Style Definition
...
bearings
Style Definition
...
Style Definition
...
Surveillance et diagnostic d'état des machines - Surveillance des vibrations —
Style Definition
...
Partie 10: Techniques de diagnostic pour les générateurs électriques de puissance de sortie supérieure à 50
Style Definition
...
MVA
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
FDIS stage
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
St l D fi iti

---------------------- Page: 1 ----------------------
ISO/FDIS 13373-10:2024(en)
Formatted: Font: Bold
Formatted: HeaderCentered
Formatted: Right: 1.5 cm, Bottom: 1 cm, Gutter: 0 cm,
© ISO 2024
Header distance from edge: 1.27 cm, Footer distance
from edge: 0.5 cm
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
Commented [eXtyles1]: The reference "ISO 2024" is to a
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
withdrawn standard
at the address below or ISO’s member body in the country of the requester.
Formatted: Default Paragraph Font
ISO copyright office Formatted: Default Paragraph Font
CP 401 • Ch. de Blandonnet 8
Formatted: Indent: Left: 0 cm, Right: 0 cm, Space
CH-1214 Vernier, Geneva
Before: 0 pt, No page break before, Adjust space
Phone: + 41 22 749 01 11
between Latin and Asian text, Adjust space between
EmailE-mail: copyright@iso.org
Asian text and numbers
Website: www.iso.orgwww.iso.org
Formatted: French (France)
Published in Switzerland
Formatted: French (France)
Formatted: French (France)
Formatted: FooterPageRomanNumber
© ISO 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO/FDIS 13373-10:2024(en)
Formatted: Font: 11 pt, Bold
Formatted: Font: Bold
Formatted: HeaderCentered, Left
Contents
Formatted: Adjust space between Latin and Asian text,
Adjust space between Asian text and numbers
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Measurements . 2
4.1 Vibration measurements . 2
4.2 Machine operational parameter measurement . 2
5 Initial analysis . 3
6 Specific analysis of electrical generators with fluid film bearings .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 20816-2:2017/Amd 1:2024(Amendment)
Mechanical vibration — Measurement and evaluation of machine vibration — Part 2: Land-based gas turbines, steam turbines and generators in excess of 40 MW, with fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min — Amendment 1
  • Standard
    1 page
    English language
    sale 15% off
  • Draft
    1 page
    English language
    sale 15% off
  • Draft
    1 page
    English language
    sale 15% off
ISO
ISO 20816-3:2022(Main)
Mechanical vibration — Measurement and evaluation of machine vibration — Part 3: Industrial machinery with a power rating above 15 kW and operating speeds between 120 r/min and 30 000 r/min

This document specifies the general requirements for evaluating the vibration of various coupled industrial machine types with a power above 15 kW and operating speeds between 120 r/min and 30 000 r/min when measurements are made in-situ. Guidelines for applying evaluation criteria are provided for measurements taken on non-rotating and rotating parts under normal operating conditions. The guidelines are presented in terms of both steady running vibration values and in terms of changes to vibration magnitude, which can occur in these steady values. The numerical values presented are intended to serve as guidelines based on worldwide machine experience, but shall be applied with due regard to specific machine features which can cause these values to be inappropriate. In general, the condition of a machine is assessed by consideration of both the shaft vibration and the associated structural vibration, as well as specific frequency components, which do not always relate to the broadband severity values presented. The machine types covered by this document include: a) steam turbines and generators with outputs less than or equal to 40 MW (see Note 1 and Note 2); b) steam turbines and generators with outputs greater than 40 MW which normally operate at speeds other than 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min (although generators seldom fall into this category) (see Note 1); c) rotary compressors; d) industrial gas turbines with outputs less than or equal to 3 MW (see Note 2); e) turbofans; f) electric motors of any type, if the coupling is flexible. When a motor is rigidly coupled to a machine type covered by any other part of ISO20816, the motor may be assessed either against that other part or against ISO 20816-3; g) rolls and mills; h) conveyors; i) variable speed couplings; and j) blowers or fans (see Note 3). NOTE 1 Land based steam turbines, gas turbines and generators of greater than 40 MW capacity, which run at 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min are covered by the requirements of ISO 20816-2. Generators in hydro-electric plants are covered by ISO 20816-5. NOTE 2 Gas turbines of power greater than 3 MW are covered by ISO 20816-4. NOTE 3 The vibration criteria presented in this document are generally only applicable to fans with power ratings greater than 300 kW or fans which are not flexibly supported. As and when circumstances permit, recommendations for other types of fans, including those of lightweight sheet-metal construction, will be prepared. Until these recommendations are available, classifications can be agreed between the manufacturer and the customer; using results of previous operational experience (see also ISO 14694). Machinery including a geared stage can fall under the scope of this document. For performing acceptance tests of gearboxes please refer to ISO 20816-9. The following types of industrial machine are not covered by this document: k) land-based gas turbines, steam turbines and generators with power outputs greater than 40 MW and speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min (see ISO20816‑2); l) gas turbine sets with power outputs greater than 3 MW (see ISO20816‑4); m) machine sets in hydraulic power generating and pumping plants (see ISO20816‑5); n) reciprocating machines and machines solidly coupled to reciprocating machines (see ISO10816‑6); o) rotordynamic pumps and any integrated or solidly coupled electric motors where the impeller is mounted directly on the motor shaft or is rigidly attached to it (see ISO10816‑7); p) reciprocating compressor systems (see ISO 20816-8); q) rotary positive displacement compressors (e. g. screw compressors); r) submerged motor-pumps; and s) wind turbines (see ISO10816‑21). The requirements of this document apply to in-situ broad-band vibration measurements taken on the shafts, bearings, bearing pedestals, or housings of machines under steady-state operating conditions within their nominal

  • Standard
    24 pages
    English language
    sale 15% off
  • Standard
    25 pages
    French language
    sale 15% off
ISO
ISO 14839-5:2022(Main)
Mechanical vibration — Vibration of rotating machinery equipped with active magnetic bearings — Part 5: Touch-down bearings

This document gives guidelines for identifying: a) The typical architectures of touch-down bearing systems to show which components are likely to comprise such systems and which functions these components provide; NOTE Touch-down bearings are also known as “backup bearings”, “auxiliary bearings”, “catcher bearings” or “landing bearings”. Within this document, the term “touch-down bearings” is used exclusively as defined in ISO 14839‑1. b) The functional requirements for touch-down bearing systems so that clear performance targets can be set; c) Elements to be considered in the design of the dynamic system such that rotordynamic performance can be optimized, both for touch-down bearings and active magnetic bearings (AMBs); d) The environmental factors that have significant impact on touch-down bearing system performance allowing optimization of overall machine design; e) The AMB operational conditions that can give rise to contact within the touch-down bearing system so that such events can be considered as part of an overall machine design. It also considers failure modes within the AMB system that can give rise to a contact event. This ensures that the specification of the touch-down bearings covers all operational requirements; f) The most commonly encountered touch-down bearing failure modes and typical mechanisms for managing these events; g) Typical elements of a design process for touch-down bearing systems including the specification of load requirements, the sizing process, the analytical and simulation methods employed for design validation; h) The parameters to be taken into account when designing a touch-down bearing system acceptance test programme including the test conditions to be specified and the associated instrumentation to be used to ensure successful test execution; i) The condition monitoring and inspection methods that allow the status of in-service touch-down bearings to be evaluated and when necessary identifying the corrective actions to be taken; j) The factors to be considered when designing the maintenance regime for a touch-down bearing system including the actions to be taken after specified events have occurred together with any actions to be performed on a regular basis; k) The factors to be considered regarding other life cycle topics (e.g. obsolescence management, de-commissioning and disposal).

  • Standard
    43 pages
    English language
    sale 15% off
ISO
ISO 22266-1:2022(Main)
Mechanical vibration — Torsional vibration of rotating machinery — Part 1: Evaluation of steam and gas turbine generator sets due to electrical excitation

This document provides guidelines for the assessment of torsional natural frequencies and component strength, under normal operating conditions, for the coupled shaft train, including long elastic rotor blades, of steam and gas turbine generator sets. In particular, the guidelines apply to the torsional responses of the coupled shaft train at grid and twice grid frequencies due to electrical excitation of the electrical network to which the turbine generator set is connected. Excitation at other frequencies (e.g. subharmonic frequencies) are not covered in this document. No guidelines are given regarding the torsional vibration response caused by steam excitation or other excitation mechanisms not related to the electrical network. Where the shaft cross sections and couplings do not fulfil the required strength criteria and/or torsional natural frequencies do not conform with defined frequency margins, other actions shall be defined to resolve the problem. The requirements included in this document are applicable to a) steam turbine generator sets connected to the electrical network, and b) gas turbine generator sets connected to the electrical network. Methods currently available for carrying out both analytical assessment and test validation of the shaft train torsional natural frequencies are also described. NOTE Radial (lateral, transverse) and axial vibration of steam and/or gas turbine generator sets is dealt with in ISO 20816-2.

  • Standard
    38 pages
    English language
    sale 15% off
  • Standard
    38 pages
    English language
    sale 15% off
  • Standard
    40 pages
    French language
    sale 15% off
ISO
ISO 13373-4:2021(Main)
Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 4: Diagnostic techniques for gas and steam turbines with fluid-film bearings

This document sets out guidelines for the specific procedures to be considered when carrying out vibration diagnostics of various types of gas and steam turbines with fluid-film bearings. This document is intended to be used by condition monitoring practitioners, engineers and technicians and provides a practical step-by-step vibration-based approach to fault diagnosis. In addition, it gives examples for a range of machine and component types and their associated fault symptoms. The approach given in this document is based on established good practice, put together by experienced users, although it is acknowledged that other approaches can exist. Recommended actions for a particular diagnosis depend on individual circumstances, the degree of confidence in the fault diagnosis (e.g. has the same diagnosis been made correctly before for this machine), the experience of the practitioner, the fault type and severity as well as on safety and commercial considerations. It is neither possible nor the aim of this document to recommend actions for all circumstances.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    27 pages
    French language
    sale 15% off
ISO
ISO 20816-9:2020(Main)
Mechanical vibration — Measurement and evaluation of machine vibration — Part 9: Gear units

This document specifies requirements for determining and classifying mechanical vibration of individually housed, enclosed, speed increasing or speed reducing gear units. It specifies methods for measuring housing and shaft vibrations, and the types of instrumentation, measurement methods and testing procedures for determining vibration magnitudes. Vibration grades for acceptance are included. Torsional vibration measurements are outside the scope of this document. It applies to a gear unit operating within its design speed, load, temperature and lubrication range for acceptance testing at the manufacturer's facility. By agreement between manufacturer and customer and/or operator, it can be used for guidelines for on-site acceptance testing and for routine operational measurements. This document applies to gear units of nominal power rating from 10 kW to 100 MW and nominal rotational speeds between 30 r/min and 12 000 r/min (0,5 Hz to 200 Hz). This document does not apply to special or auxiliary drive trains, such as integrated gear-driven compressors, pumps, turbines, etc., or gear type clutches used on combined-cycle turbo generators and power take-off gears. The evaluation criteria provided in this document can be applied to the vibration of the main input and output bearings of the gearbox and to the vibration of internal shaft bearings. They can have limited application to the evaluation of the condition of those gears. Specialist techniques for evaluating the condition of gears are outside the scope of this document. This document establishes provisions under normal steady-state operating conditions for evaluating the severity of the following in-situ broad-band vibration: a) structural vibration at all main bearing housings or pedestals measured radially (i.e. transverse) to the shaft axis; b) structural vibration at thrust bearing housings measured in the axial direction; c) vibration of rotating shafts radially (i.e. transverse) to the shaft axis at, or close to, the main bearings; d) structural vibration on the gear casing. NOTE Vibration occurring during non-steady-state conditions (when transient changes are taking place), including run up or run down, initial loading and load changes are outside the scope of this document.

  • Standard
    19 pages
    English language
    sale 15% off
ISO
ISO 13373-5:2020(Main)
Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 5: Diagnostic techniques for fans and blowers

This document sets out the specific procedures to be considered when carrying out vibration diagnostics of various types of fans and blowers. This document is intended to be used by condition monitoring practitioners, engineers and technicians and provides a practical, step-by-step, vibration-based approach to fault diagnosis. In addition, it gives a number of examples for a range of machine and component types and their associated fault symptoms. The approach given in this document is based on established good practice, put together by experienced users, although it is acknowledged that other approaches can exist. Recommended actions for a particular diagnosis depend on individual circumstances, the degree of confidence in the fault diagnosis (e.g. has the same diagnosis been made correctly before for this machine), the experience of the practitioner, the fault type and severity as well as on safety and commercial considerations. It is neither possible nor the aim of this document to recommend actions for all circumstances.

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    22 pages
    French language
    sale 15% off
ISO
ISO 14839-1:2018(Main)
Mechanical vibration — Vibration of rotating machinery equipped with active magnetic bearings — Part 1: Vocabulary

This document defines terms relating to rotating machinery equipped with active magnetic bearings. NOTE General terms and definitions of mechanical vibration are given in ISO 2041; those relating to balancing are given in ISO 21940-2; those relating to geometric characteristics such as coaxiality, concentricity and runout are explained in ISO 1101.

  • Standard
    22 pages
    English language
    sale 15% off
ISO
ISO 20816-8:2018(Main)
Mechanical vibration — Measurement and evaluation of machine vibration — Part 8: Reciprocating compressor systems

This document establishes procedures and guidelines for the measurement and classification of mechanical vibration of reciprocating compressor systems. The vibration values are defined primarily to classify the vibration of the compressor system and to avoid fatigue problems with parts in the reciprocating compressor system, i.e. foundation, compressor, dampers, piping and auxiliary equipment mounted on the compressor system. Shaft vibration is not considered. This document applies to reciprocating compressors mounted on rigid foundations with typical rotational speed ratings in the range 120 r/min up to and including 1 800 r/min. The general evaluation criteria which are presented relate to operational measurements. The criteria are also used to ensure that machine vibration does not adversely affect the equipment directly mounted on the machine, e.g. pulsation dampers and the pipe system. NOTE The general guidelines presented in this document can also be applied to reciprocating compressors outside the specified speed range but different evaluation criteria might be appropriate in this case. The machinery driving the reciprocating compressor, however, is evaluated in accordance with the appropriate part of ISO 10816, ISO 20816 or other relevant standards and classification for the intended duty. Drivers are not included in this document. It is recognized that the evaluation criteria might only have limited application when considering the effects of internal machine components, e.g. problems associated with valves, pistons and piston rings might be unlikely to be detected in the measurements. Identification of such problems can require investigative diagnostic techniques which are outside the scope of this document. Examples of reciprocating compressor systems covered by this document are — horizontal, vertical, V-, W- and L-type compressor systems, — constant and variable speed compressors, — compressors driven by electric motors, gas and diesel engines, steam turbines, with or without a gearbox, flexible or rigid coupling, and — dry running and lubricated reciprocating compressors. This document does not apply to hyper compressors. The guidelines are not intended for condition monitoring purposes. Noise is also outside the scope of this document.

  • Standard
    34 pages
    English language
    sale 15% off
  • Standard
    34 pages
    French language
    sale 15% off
ISO
ISO 20816-5:2018(Main)
Mechanical vibration — Measurement and evaluation of machine vibration — Part 5: Machine sets in hydraulic power generating and pump-storage plants

This document provides guidelines for evaluating the vibration measurements made at the bearings, bearing pedestals or bearing housings and also for evaluating relative shaft vibration measurements made on machine sets in hydraulic power generating and pump-storage plants when the machine is operating within its normal operating range. The normal operating ranges for each type of turbine covered by this document are defined in Annex A. This document is applicable to machine sets in hydraulic power generating plants and in pump-storage plants with typical rotational speeds of 60 r/min to 1 000 r/min fitted with shell or pad (shoe) type oil-lubricated bearings. NOTE The current database includes machine speeds ranging from 60 r/min to 750 r/min (with a very small sample of 1 000 r/min machines). This document defines different limit values of bearing housing and shaft vibration depending on the type of turbine, the orientation of the shaft (i.e. horizontal or vertical) and for each of the bearing locations. This document is based on statistical analysis and provides criteria for the most common types of turbines, pump-turbines and pumps. For specific information on which types of units are covered in this document, see Annex A. Machine sets covered by this document can have the following configurations: a) generators driven by hydraulic turbines; b) motor-generators driven by pump-turbines; c) motor-generators driven by hydraulic turbines and separate pumps; d) pumps driven by electric motors. This document is not applicable to the following unit configurations, parameters and operating conditions: — hydraulic machines with water-lubricated bearings; — hydraulic machines or machine sets having rolling element bearings (for these machines, see IEC 62006 and/or ISO 10816‑3); — pumps in thermal power plants or industrial installations (for these machines, see ISO 10816‑7); — electrical machines operating as motors except for the use of these machines in pump-storage applications; — hydro generators operating as synchronous condensers (with the water in the turbine depressed by compressed air); — assessment of absolute bearing housing vibration displacement; — assessment of axial vibration; — assessment of transient conditions; — non-synchronous operation; — assessment of vibration of the generator stator core or the stator frame level. Measurements made of the bearing housing vibration and shaft vibration occurring in machine sets in hydraulic power generating and pump-storage plants can be used for the following purposes: 1) Purpose A: to prevent damage arising from excessive vibration magnitudes; 2) Purpose B: to monitor changes in vibrational behaviour in order to allow diagnosis and/or prognosis. The criteria are applicable for the vibration produced by the machine set itself. Special investigation is needed for vibration transmitted to the machine set from external sources, e.g. transmitted to the machine via the station foundations.

  • Standard
    51 pages
    English language
    sale 15% off
  • Standard
    53 pages
    French language
    sale 15% off