ISO 9536:1989

Woodworking machines — Mortising machines with oscillating tool action — Nomenclature

Specifies the nomenclature appropriate to the various parts of these mortising machines in order to assist manufacturers and users in the identification of these parts. Gives in addition to terms used in two of the three official ISO languages (English and French) the equivalent terms in the German, Spanish and Italian languages.

Machines à bois — Mortaiseuses à outil oscillant — Nomenclature

General Information

• Status: Withdrawn
• Publication Date: 17-May-1989
• Withdrawal Date: 17-May-1989
• ICS: 01.040.79 - Wood technology (Vocabularies)
• ICS: 79.120.10 - Woodworking machines
• Technical Committee: ISO/TC 39/SC 4 - Woodworking machines
• Drafting Committee: ISO/TC 39/SC 4 - Woodworking machines
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 20-Jun-2016

Standards Content (Sample)

INTERNATIONAL
ISO
STANDARD
9536
First edition
Premiere Edition
NORME
1989-06-01
INTERNATIONALE
Woodworking machines - Mortising machines
with oscillating tool action - Nomenclature
Machines 6 bois -
Mortaiseuses G outil
oscillant - Nomenclature
Reference number
Numero de rkference
ISO 9536 : 1989 (E/F)

---------------------- Page: 1 ----------------------
ISO 9536 : 1989 WF)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of
national Standards bodies (ISO member bodies). The work of preparing International
Standards is normally carried out through ISO technical committees. Esch member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (1 EC) on all
matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the ISO Council. They are approved in accordance with ISO procedures requiring at
least 75 % approval by the member bodies voting.
International Standard ISO 9536 was prepared by Technical Committee ISO/TC 39,
Machine tools.
Annex A of this International Standard is for information only.
0 ISO 1989
All rights reserved. No part of this publication may be reproduced or utilized in any form or by any
means, electronie or mechanical, including photocopying and microfilm, without Permission in
writing from the publisher./Droits de reproduction reserves. Aucune Partie de cette publication
ne peut etre reproduite ni utilisee sous quelque forme que ce soit et par aucun procede, electroni-
que ou mecanique, y compris Ia photocopie et les microfilms, sans I’accord ecrit de I’editeur.
International Organkation for Standardkation
Case postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland/lmprime en Suisse
ii

---------------------- Page: 2 ----------------------
ISO 9536 : 1989 (E/F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une federation mondiale
d’organismes nationaux de normalisation (comites membres de I’ISO). L’elaboration
des Normes internationales est en general confiee aux comites techniques de I’ISO.
Chaque comite membre interesse par une etude a Ie droit de faire Partie du comite
technique cr& a cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec I’ISO participent egalement aux travaux. L’ISO col-
labore etroitement avec Ia Commission electrotechnique internationale (GEI) en ce qui
concerne Ia normalisation electrotechnique.
Les projets de Normes internationales adoptes par les comites techniques sont soumis
aux comites membres pour approbation, avant leur acceptation comme Normes inter-
nationales par Ie Conseil de I’ISO. Les Normes internationales sont approuvees confor-
mement aux procedures de I’ISO qui requierent I’approbation de 75 % au moins des
comites membres votants.
La Norme internationale ISO 9536 a etc elaboree par Ie comite technique ISO/TC 39,
Machines-outils.
internationale est donnee uniquement a titre d’infor-
L’annexe A de Ia presente
mation.

---------------------- Page: 3 ----------------------
This page intentionally left blank

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD
ISO 9536 : 1989 (E/F)
NORME INTERNATIONALE
Woodworking machines -
Machines 3 bois -
Mortising machines with
Mortaiseuses 6 outil
oscillating tool action - oscillant - Nomenclature
Nomenclature
1 Scope 1 Domaine d’application
La presente Norme internationale indique Ia nomenclature
This International Standard specifies the nomenclature appro-
priate to the various Parts of mortising machines with propre aux differentes Parties des mortaiseuses a outil oscillant,
afin d’aider les constructeurs et les utilisateurs dans I’identifi-
oscillating tool action in Order to assist manufacturers and users
in the identification of these Parts. cation de ces Parties.
NOTE - In addition to terms used in two of the three official ISO NOTE - En complement des termes utilises dans deux des trois
langues officielles de I’ISO (anglais et francais), cette Norme internatio-
languages (English and French), this International Standard gives the
nale donne les termes equivalents dans les langues allemande, espa-
equivalent terms in the German, Spanish and Italian languages; these
are published under the responsibility of the member bodies for gnole et italienne; ces termes sont publies sous Ia responsabilite des
comites membres de I’Allemagne, R.F. (DIN), de I’Espagne (AENOR)
Germany, F.R. (DIN), Spain (AENOR) and Italy (UNI). However, only
the terms given in the official languages tan be considered as ISO et de I’ltalie (UNI). Toutefois, seuls les termes donnes dans les langues
officielles peuvent etre consideres comme etant des termes de I’ISO.
terms.
La presente Norme internationale s’applique aux machines
This International Standard applies to those machines desig-
nated by the number 12.51 in ISO 7984’). designees sous Ie numero 12.51 de I’ISO 7984’).
1) ISO 7984 : 1988, Woodworking machines - Technical classifi-
1) ISO 7984 : 1988, Maehines 2 bois - Classification technique des
cation of woodworking machines and auxiliary machines for wood-
machines $I travaier Ie bois et des machines auxiliaires In travaier Ie
working. bois.
1

---------------------- Page: 5 ----------------------
ISO 9536 : 1989 (E/F)
2 Nomenclature
5.8 5.2
I
31 .
11 .
P I

---------------------- Page: 6 ----------------------
ISO 9536 : 1989 (E/F)
56 .
5.4 5-3
\ I
42 . 4.5 & 4.6$$
4.4 4
E! m
106 . .
IO 7

---------------------- Page: 7 ----------------------
ISO 9536 : 1989 (E/F)
French
English
Francais
Anglais
Reference
Repere
Mortising machines with oscillating
Mortaiseuses a outil oscillant
tool action
Ossature
Framework
1
Bati
1.1 Body
Socle
1.2 Base
Deplacement des pieces et/ou outils
Feed of workpiece and/or tools
2
Cylindre pour effectuer Ie deplacement de
2.1 Table drive roller
Ia table
Valve de regulation du deplacement de Ia
2.2 Table regulating valve
table
Glissiere de deplacement vertical de I’unite
2.3 Slide for vertical movement of cutterhead
de travail
Vis de montee
2.4 -ifting screw (rise and fall screw)
Cliquet de montee
‘awl (rise and fall catch)
2.5
Plaque d’inclinaison de I’unite de travail
2.6 Norkhead unit pivoting plate
Coulisse de deplacement horizontal de
Norkhead horizontal slide
2.7
I’unite de travail
Coussinet
3earing
2.8
Butee de profondeur de Penetration des
2.9 Vlortise depth stop
outils
Glissiere deplacement table
2.10 Table adjustment
Support, maintien et guidage des
3 Workpiece support, clamp and guide
pieces
Table porte-piece
3.1 Work-ta ble
Dispositif de reglage de Ia Position de
Table stop arrangement
3.2
depart de Ia table
Presseur de piece
Workpiece clamp
3.3
Butee pour piece
3.4 Workpiece stop
Colonnes de deplacement des presses
3.5 Head-slide column
Porte-outils et outils
4 Tool-holders and tools
Bedane
4.1 Chisel (for mortising)
Bedane a deux dents
4.2 Chisel with two teeth
Bedane a plusieurs dents
Chisel with several teeth
4.3
Bedane a barbette
4.4 Stepped mortising tool
Bedane double
Tool for side-by-side mortise
4.5
Bedane fer a cheval
4.6 Tool for end-to-end mortise
Ciseau
Incising tool (chisel)
4.7
Porte-ciseau lateral
4.8 Lateral chisel block
Collier de serrage du bedane
Chisel-locking collar
4.9
Boulon porte-ciseau
4.10 Chisel-block bolt
Unite de travail et son entrainement
5 Workhead and tool drives
Tete mortaisage
5.1 Mortising head
Moteur d’entrainement de Ia tete
Mortising head motor
5.2
mortaisage
Excentrique reglable
Eccentric shaft adjustment
5.3
Bielle
5.4 Rod
Bielle laterale
Lateral rod
5.5
Pivot
5.6 Pivot
Courroies trapezo’idales
V-belts
5.7
Dispositif de reglage de Ia tete en hauteur
5.8 Head height regulato
...