ISO 17544:2004

Carbonaceous materials used in the production of aluminium — Cold and tepid ramming pastes — Determination of rammability of unbaked pastes

ISO 17544:2004 describes a method of producing a compaction curve indicating the rammability of carbonaceous ramming pastes used to line cathodes utilized in the production of aluminium.

Produits carbonés utilisés pour la production de l'aluminium — Pâtes de brasquage froides et tièdes — Détermination de l'aptitude au brasquage des pâtes non cuites

General Information

• Status: Published
• Publication Date: 15-Jul-2004
• ICS: 71.100.10 - Materials for aluminium production
• Technical Committee: ISO/TC 226 - Materials for the production of primary aluminium
• Drafting Committee: ISO/TC 226 - Materials for the production of primary aluminium

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 17544
First edition
2004-07-15

Carbonaceous materials used in the
production of aluminium — Cold and
tepid ramming pastes — Determination of
rammability of unbaked pastes
Produits carbonés utilisés pour la production de l'aluminium — Pâtes de
brasquage froides et tièdes — Détermination de l'aptitude au
brasquage des pâtes non cuites




Reference number
ISO 17544:2004(E)
©
ISO 2004

---------------------- Page: 1 ----------------------
ISO 17544:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 17544:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17544 was prepared by Technical Committee ISO/TC 47, Chemistry, Subcommittee SC 7, Aluminium
oxide, cryolite, aluminium fluoride, sodium fluoride, carbonaceous products for the aluminium industry.

© ISO 2004 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 17544:2004(E)

Carbonaceous materials used in the production of aluminium —
Cold and tepid ramming pastes — Determination of rammability
of unbaked pastes
1 Scope
This International Standard describes a method of producing a compaction curve indicating the rammability of
carbonaceous ramming pastes used to line cathodes utilized in the production of aluminium.
Determination of the rammability enables a ramming paste with the optimum density to be selected.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method
for the determination of repeatability and reproducibility of a standard measurement method
ISO 14422, Carbonaceous materials used in the production of aluminium — Cold-ramming pastes — Methods
of sampling
3 Symbols
h measured height of test specimen, in cm
m mass of paste placed in cylinder, in g
N number of impacts
N2 minimum value of second derivative of ρ(N)
r inner radius of rammer cylinder, in cm
α scaling or normalization parameter describing the steepness of the compaction curve (which
decreases as α increases)
γ location parameter which shifts the origin of the distribution
−3
ρ maximum value of density, in g⋅cm
max
ρ initial value of density, representative of loose compaction of the paste under its own weight,
0
−3
in g⋅cm
−3
ρ(N) density after N impacts, in g⋅cm
© ISO 2004 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 17544:2004(E)
ρ(N)' first derivative of ρ(N)
ρ(N)'' second derivative of ρ(N)
ρ(N)''' third derivative of ρ(N)
−3
ρ(50) density after 50 impacts, in g⋅cm
−3
ρ(100) density after 100 impacts, in g⋅cm
−3
∆ρ pre-exponential factor, in g⋅cm : ∆ρ = ρ − ρ
max 0
4 Principle
Ramming paste is compacted in a laboratory rammer. The paste is subjected to a total of 350 impacts. The
density of the paste is measured as a function of the number of impacts. The data is fitted to a three-
parameter cumulative Weibull distribution function given by the following equation:
6

log N−γ
10

ρρ()N=−∆ρ×exp− (1)
max 
α



A ramming parameter N2, corresponding to the number of impacts for which the second derivative of the
Weibull function has a minimum value, is then calculated.
An alternative method of evaluation is to determine the ratio of the density after 50 impacts to the density after
100 impacts, as shown by the following formula:
ρ(50)
(2)
ρ(100)
5 Apparatus
An example of a rammer mould is shown in Figure 1.
5.1 Rammer cylinder, made of steel, with an inner diameter of 50 mm.
5.2 Ram base, made of steel. The ram base shall fit into the rammer cylinder and act as the bottom of the
cylinder.
5.3 Rammer, consisting of a steel piston, a falling weight mounted so that it can be dropped onto the top of
the piston, and a height-measuring device accurate to 0,1 mm. The mass of the falling weight shall be 6,35 kg
and the weight shall travel a constant distance to impact of (50 ± 0,1) mm.
5.4 Box (with lid), capable of containing the amount of ramming paste needed to produce one test
specimen. The free space over the paste shall not be more than 50 % of the volume of the paste.
5.5 Heating/cooling cabinet, capable of being maintained at a cons
...