ISO 11119-2:2020/Amd 1:2023

Gas cylinders — Design, construction and testing of refillable composite gas cylinders and tubes — Part 2: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l with load-sharing metal liners — Amendment 1

Bouteilles à gaz — Conception, construction et essais des tubes et bouteilles à gaz rechargeables en matériau composite — Partie 2: Tubes et bouteilles à gaz entièrement bobinés en matériau composite renforcés de fibres et d'une contenance allant jusqu'à 450 l avec liners métalliques structuraux — Amendement 1

General Information

• Status: Published
• Publication Date: 10-May-2023
• ICS: 23.020.35 - Gas cylinders
• Technical Committee: ISO/TC 58/SC 3 - Cylinder design
• Drafting Committee: ISO/TC 58/SC 3 - Cylinder design
• Current Stage: 6060 - International Standard published
• Start Date: 11-May-2023
• Due Date: 22-Dec-2023
• Completion Date: 11-May-2023

Relations

• Amends: ISO 11119-2:2020 - Gas cylinders — Design, construction and testing of refillable composite gas cylinders and tubes — Part 2: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l with load-sharing metal liners
• Effective Date: 30-Jul-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11119-2
Third edition
2020-11
AMENDMENT 1
2023-05
Gas cylinders — Design, construction
and testing of refillable composite gas
cylinders and tubes —
Part 2:
Fully wrapped fibre reinforced
composite gas cylinders and tubes up
to 450 l with load-sharing metal liners
AMENDMENT 1
Bouteilles à gaz — Conception, construction et essais des tubes et
bouteilles à gaz rechargeables en matériau composite —
Partie 2: Tubes et bouteilles à gaz entièrement bobinés en matériau
composite renforcés de fibres et d'une contenance allant jusqu'à 450 l
avec liners métalliques structuraux
AMENDEMENT 1
Reference number
ISO 11119-2:2020/Amd.1:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 11119-2:2020/Amd.1:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11119-2:2020/Amd.1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IE
...