ISO/TS 16401-2:2012

Electronic fee collection — Evaluation of equipment for conformity to ISO/TS 17575-2 — Part 2: Abstract test suite

ISO/TS 16401-2:2012 specifies the Abstract Test Suite (ATS) to evaluate the conformity of Front End Communications API and Front End Application to ISO/TS 17575-2.

Perception du télépéage — Évaluation de conformité de l'équipement à l'ISO/TS 17575-2 — Partie 2: Suite d'essai abstraite

General Information

• Status: Withdrawn
• Publication Date: 23-Feb-2012
• Withdrawal Date: 23-Feb-2012
• ICS: 03.220.20 - Road transport
• ICS: 35.240.60 - IT applications in transport
• Technical Committee: ISO/TC 204 - Intelligent transport systems
• Drafting Committee: ISO/TC 204/WG 5 - Fee and toll collection
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 05-Jan-2018

Relations

• Revised: ISO/TR 16401-2:2018 - Electronic fee collection — Evaluation of equipment for conformity to ISO 17575-2 — Part 2: Abstract test suite
• Effective Date: 05-Nov-2015
• Consolidates: ISO 9735-10:2002 - Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 10: Syntax service directories
• Effective Date: 06-Jun-2022

Standards Content (Sample)

TECHNICAL ISO/TS
SPECIFICATION 16401-2
First edition
2012-03-01

Electronic fee collection — Evaluation of
equipment for conformity to
ISO/TS 17575-2 —
Part 2:
Abstract test suite
Perception du télépéage — Évaluation de conformité de l'équipement à
l'ISO/TS 17575-2 —
Partie 2: Suite d'essai abstraite




Reference number
ISO/TS 16401-2:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO/TS 16401-2:2012(E)

COPYRIGHT PROTECTED DOCUMENT


©  ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TS 16401-2:2012(E)
Contents Page
Foreword . iv
Introduction . v
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Abbreviations . 2
5  Abstract Test Method (ATM). 3
5.1  Implementations Under Tests . 3
5.1.1  Front-End (FE) . 3
5.1.2  Back-End (BE) . 3
5.2  Test architecture . 3
5.3  Protocol Implementation Extra Information for Testing (PIXIT) . 3
6  Untestable Test Purposes (TP) . 3
7  ATS data structures . 4
7.1  Implementation of proposed in ‘annex D.2. API Definition in C’ . 4
7.2  Common data types . 4
8  External functions . 4
9  Message filtering . 4
10  ATS naming conventions . 4
10.1  Definition naming conventions . 5
10.2  Test Case identifier . 6
10.3  TTCN-3 modules identifier . 6
Annex A (informative) TTCN-3 Library modules for FE and BE . 7
Annex B (informative) PIXIT Proforma for FE and BE . 8
Bibliography . 10

© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/TS 16401-2:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of normative document:
— an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members of
the parent committee casting a vote;
— an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting a
vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 16401-2 was prepared by Technical Committee ISO/TC 204, Intelligent transport systems, in
collaboration with Technical Committee CEN/TC 278, Road transport and traffic telematics.
ISO/TS 16401 consists of the following parts, under the general title Electronic fee collection — Evaluation of
equipment for conformity to ISO/TS 17575-2:
 Part 1: Test suite structure and test purposes
 Part 2: Abstract test suite
iv © ISO 2012 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/TS 16401-2:2012(E)
Introduction
This part of ISO/TS 16401 is part of a set of standards that supports interoperability of autonomous EFC-
systems, which includes ISO/TS 17575 parts 1 to 4 that define the EFC context data, their charge reports and
their use of communication infrastructure.
Within the suite of EFC standards this conformance evaluation procedure defines the process and tests for
conformity evaluation of Front End and Back End that comply with the requirements in ISO/TS 17575-2.
This part of ISO/TS 16401 is intended to
 assess Front End Communications API and Front End Application capabilities,
 assess Front End Communications API and Front End Application behaviour,
 serve as a guide for Front End Communications API and Front End Application conformance evaluation
and type approval,
 achieve comparability between the results of the corresponding tests applied in different places at
different times, and
 facilitate communications between parties.

This part of ISO/TS 16401 is based on
 ISO/TS 17575-2, and
 the ISO/IEC 9646 family of standards on conformance test methodology.

© ISO 2012 – All rights reserved v

---------------------- Page: 5 ----------------------
TECHNICAL SPECIFICATION ISO/TS 16401-2:2012(E)

Electronic fee collection — Evaluation of equipment for
conformity to ISO/TS 17575-2 —
Part 2:
Abstract test suite
1 Scope
This part of ISO/TS 16401 specifies the Abstract Test Suite (ATS) to evaluate the conformity of Front End
Communications API and Front End Application to ISO/TS 17575-2.
The objective of the present document is to provide a basis for conformance tests for Front End
Communications API and Front End Application in Electronic Fee Collection based on autonomous on-board
equipment (OBE) to enable interoperability between different equipment supplied by different manufacturers.
The present abstract test suite is directly derived from ISO/TS 17575-2.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO/TS 17575-1, Electronic fee collection — Application interface definition for autonomous systems —
Part 1: Charging
ISO/TS 17575-2, Electronic fee collection — Application interface definition for autonomous systems —
Part 2: Communication and connection to the lower layers
ISO/TS 17575-3, Electronic fee collection — Application interface definition for autonomous systems —
Part 3: Context data
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/TS 17575-1 and the following apply.
3.1
conformance testing
testing the extent to which an IUT is a conforming implementation
[ISO/IEC 9646-1, definition 3.3.23]
3.2
contract
expression of an agreement between two or more parties concerning the use of the road infrastructure
[ISO 14906:2011, definition 3.7]
NOTE A contract specifies obligations, permissions and prohibitions for the objects involved.
© ISO 2012 – All rights reserved 1

---------------------- Page: 6 ----------------------
ISO/TS 16401-2:2012(E)
3.3
Front End application
part of the Front End above the API
[ISO/TS 16401-1:2011, definition 3.2]
3.4
implementation under test
IUT
implementation of one or more OS1 protocols in an adjacent user/provider relationship, being that part of a
real open system which is to be studied by testing
[ISO/IEC 9646-1, definition 3.3.43]
3.5
service provider
operator that accepts the user's payment means and in return provides a road-use service to the user
NOTE Taken from ISO 14906:2004.
3.6
system under test
SUT
real open system in which the IUT resides
[ISO/IEC 9646-1, definition 3.3.103]
3.7
test case
an abstract or executable test case
[ISO/IEC 9646-1, definition 3.3.107]
3.8
toll charger
legal entity charging toll for vehicles in a toll domain
[ISO/TS 17574:2009, definition 3.27]
4 Abbreviations
For the purposes of this document, the abbreviations given in ISO/TS 16401-1 and the following apply.
EUT Equipment
...