ISO 17082:2004

Pneumatic fluid power — Valves — Data to be included in supplier literature

ISO 17082:2004 specifies which data are to be included in the manufacturer's supplier literature that accompanies any kind of pneumatic valve. These data are vital in selecting the proper valve for a particular application.

Transmissions pneumatiques — Distributeurs — Données à inclure dans la documentation des fournisseurs

L'ISO 17082 2004 spécifie quelles données doivent être incluses dans la documentation du fournisseur accompagnant n'importe quelle sorte de distributeur pneumatique. Ces données sont essentielles à la sélection du distributeur approprié pour une application particulière.

Fluidna tehnika – Pnevmatika – Ventili – Kataloški podatki, ki morajo biti vključeni v dokumentaciji dobavitelja

General Information

• Status: Published
• Publication Date: 10-Jun-2004
• ICS: 23.100.50 - Control components
• Technical Committee: ISO/TC 131/SC 5 - Control products and components
• Drafting Committee: ISO/TC 131/SC 5/WG 3 - Pneumatic control products
• Current Stage: 9060 - Close of review
• Start Date: 04-Jun-2029
• Ref Project: SIST ISO 17082:2005 - Pneumatic fluid power -- Valves -- Data to be included in supplier literature

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 17082
First edition
2004-06-01


Pneumatic fluid power — Valves — Data
to be included in supplier literature
Transmissions pneumatiques — Distributeurs — Données à inclure
dans la documentation des fournisseurs





Reference number
ISO 17082:2004(E)
©
ISO 2004

---------------------- Page: 1 ----------------------
ISO 17082:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 17082:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17082 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 5,
Control products and components.
© ISO 2004 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 17082:2004(E)
Introduction
In pneumatic fluid power systems, power is transmitted and controlled through air under pressure within a
circuit. Typical components found in such systems are pneumatic valves. These devices control flow direction,
pressure or flow rate of air in the circuit.

iv © ISO 2004 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 17082:2004(E)

Pneumatic fluid power — Valves — Data to be included in
supplier literature
1 Scope
This International Standard specifies which data are to be included in the manufacturer’s supplier literature
that accompanies any kind of pneumatic valve. These data are vital in selecting the proper valve for a
particular application.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1219-1, Fluid power systems and components — Graphic symbols and circuit diagrams — Part 1:
Graphic symbols
ISO 3448, Industrial liquid lubricants — ISO viscosity classification
ISO 4400, Fluid power systems and components — Three-pin electrical plug connectors with earth contact —
Characteristics and requirements
ISO 5598, Fluid power systems and components — Vocabulary
ISO 5599-1, Pneumatic fluid power — Five-port directional control valves — Part 1: Mounting interface
surfaces without electrical connector
ISO 5599-2, Pneumatic flu
...

SLOVENSKI STANDARD
SIST ISO 17082:2005
01-november-2005
)OXLGQDWHKQLND±3QHYPDWLND±9HQWLOL±.DWDORãNLSRGDWNLNLPRUDMRELWLYNOMXþHQL
YGRNXPHQWDFLMLGREDYLWHOMD
Pneumatic fluid power -- Valves -- Data to be included in supplier literature
Transmissions pneumatiques -- Distributeurs -- Données à inclure dans la
documentation des fournisseurs
Ta slovenski standard je istoveten z: ISO 17082:2004
ICS:
23.100.50 Krmilni sestavni deli Control components
SIST ISO 17082:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 17082:2005

---------------------- Page: 2 ----------------------

SIST ISO 17082:2005


INTERNATIONAL ISO
STANDARD 17082
First edition
2004-06-01


Pneumatic fluid power — Valves — Data
to be included in supplier literature
Transmissions pneumatiques — Distributeurs — Données à inclure
dans la documentation des fournisseurs





Reference number
ISO 17082:2004(E)
©
ISO 2004

---------------------- Page: 3 ----------------------

SIST ISO 17082:2005
ISO 17082:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 17082:2005
ISO 17082:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17082 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 5,
Control products and components.
© ISO 2004 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 17082:2005
ISO 17082:2004(E)
Introduction
In pneumatic fluid power systems, power is transmitted and controlled through air under pressure within a
circuit. Typical components found in such systems are pneumatic valves. These devices control flow direction,
pressure or flow rate of air in the circuit.

iv © ISO 2004 – All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 17082:2005
INTERNATIONAL STANDARD ISO 17082:2004(E)

Pneumatic fluid power — Valves — Data to be included in
supplier literature
1 Scope
This International Standard specifies which data are to be included in the manufacturer’s supplier literature
that accompanies any kind of pneumatic valve. These data are vital in selecting the proper valve for a
particula
...

NORME ISO
INTERNATIONALE 17082
Première édition
2004-06-01


Transmissions pneumatiques —
Distributeurs — Données à inclure dans
la documentation des fournisseurs
Pneumatic fluid power — Valves — Data to be included in supplier
literature





Numéro de référence
ISO 17082:2004(F)
©
ISO 2004

---------------------- Page: 1 ----------------------
ISO 17082:2004(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


©  ISO 2004
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Publié en Suisse

ii © ISO 2004 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 17082:2004(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 17082 a été élaborée par le comité technique ISO/TC 131, Transmissions hydrauliques et
pneumatiques, sous-comité SC 5, Appareils de régulation et de distribution et leurs composants.
© ISO 2004 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 17082:2004(F)
Introduction
Dans les systèmes de transmissions pneumatiques, l'énergie est transmise et commandée par l'intermédiaire
d'un gaz sous pression circulant dans un circuit. Les distributeurs pneumatiques sont des composants types
trouvés dans de tels systèmes. Ces appareils commandent le sens d'écoulement, la pression ou le débit d'air
dans le circuit.

iv © ISO 2004 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 17082:2004(F)

Transmissions pneumatiques — Distributeurs — Données à
inclure dans la documentation des fournisseurs
1 Domaine d'application
La présente Norme internationale spécifie quelles données doivent être incluses dans la documentation du
fournisseur accompagnant n'importe quelle sorte de distributeur pneumatique. Ces données sont essentielles
à la sélection du distributeur approprié pour une application particulière.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour
...