ISO 29022:2013
(Main)Dentistry — Adhesion — Notched-edge shear bond strength test
Dentistry — Adhesion — Notched-edge shear bond strength test
ISO 29022:2013 specifies a shear test method used to determine the adhesive bond strength between direct dental restorative materials and tooth structure, e.g. dentine or enamel. The method as described is principally intended for dental adhesives. The method includes substrate selection, storage and handling of tooth structure, as well as the procedure for testing.
Médecine bucco-dentaire — Adhérence — Essai de résistance au cisaillement sur échantillons à bord entaillé
L'ISO 29022:2013 spécifie une méthode d'essai de cisaillement qui permet de déterminer la force d'adhérence entre les produits de restauration dentaire directe et la structure dentaire, par exemple la dentine ou l'émail. La méthode décrite est principalement destinée aux adhésifs dentaires. La méthode comprend le choix du substrat, le stockage et le conditionnement de la structure dentaire, ainsi que le mode opératoire d'essai.
General Information
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 29022
First edition
2013-06-01
Dentistry — Adhesion — Notched-
edge shear bond strength test
Médecine bucco-dentaire — Adhérence — Essai de résistance au
cisaillement sur échantillons à bord entaillé
Reference number
©
ISO 2013
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Tooth substrate and storage . 1
4.1 General . 1
4.2 Time after extraction . 2
4.3 Condition of teeth . 2
4.4 Initial preparation and storage of teeth . 2
5 Tooth surface preparation . 2
5.1 General . 2
5.2 Potting (mounting) of teeth . 2
5.3 Surface preparation . 3
5.4 Storage of prepared specimens . 3
6 Specimen production, handling and storage . 3
6.1 General . 3
6.2 Preconditioning . 3
6.3 Application of adhesive . 3
6.4 Insertion into bonding clamp . 4
6.5 Composite placement . 4
6.6 Specimen handling and storage . 4
7 Notched-edge shear test . 5
7.1 Apparatus . 5
7.2 Shear loading . 6
7.3 Test . 6
7.4 Recording and treatment of results . 6
7.5 Report . 6
Annex A (normative) Detailed drawings of notched-edge shear apparatus .8
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
ISO 29022 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 1, Filling and
restorative materials.
iv © ISO 2013 – All rights reserved
Introduction
The International Organization for Standardization (ISO) draws attention to the fact that it is claimed that
compliance with this document may involve the use of a patent concerning testing shear bond strength.
ISO takes no position concerning the evidence, validity and scope of this patent right.
The holder of this patent right has ensured ISO that he/she is willing to negotiate licenses under
reasonable and non-discriminatory terms and conditions with applicants throughout the world. In
this respect, the statement of the holder of this patent right is registered with ISO. Information may be
obtained from:
Neil T. Jessop, Ultradent Products, Inc., 505 West 10200 South, South Jordan, Utah 84095-3942, USA.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights other than those identified above. ISO shall not be held responsible for identifying any or
all such patent rights.
The purpose of this International Standard is to establish a simple and easy to use method for documenting
a claim that a material adheres to tooth substance. While the method described in this International
Standard has been used for comparing dental adhesive materials, users of this International Standard
should evaluate usefulness of this method for their particular application(s). There is a variety of other
dental adhesion test methods that may also be suitable or preferable, depending on the objective (e.g.
academic research).
INTERNATIONAL STANDARD ISO 29022:2013(E)
Dentistry — Adhesion — Notched-edge shear bond
strength test
1 Scope
This International Standard specifies a shear test method used to determine the adhesive bond strength
between direct dental restorative materials and tooth structure, e.g. dentine or enamel. The method as
described is principally intended for dental adhesives. The method includes substrate selection, storage
and handling of tooth structure, as well as the procedure for testing.
NOTE 1 Testing adhesion to tooth structure is technique sensitive and experience with the test method is required.
NOTE 2 With modification, it may be possible to use this method for adhesive restorative materials (e.g. glass-
ionomer materials).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 1942, Dentistry — Vocabulary
ISO 3696, Water for analytical laboratory use — Specification and test methods
ISO 6344−1, Coated abrasives — Grain size analysis — Part 1: Grain size distribution test
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1942 and the following apply.
3.1
bond strength
force per unit area required to break a bonded assembly with failure occurring in or near the
adhesive/adherend interface
3.2
direct dental restorative material
material used to restore a tooth that is placed in the plastic or unset state and sets intraorally when
used clinically
3.3
substrate
material upon the surface of which an adhesive is spread for any purpose, such as bonding or coating
4 Tooth substrate and storage
4.1 General
Use bovine incisors or human erupted permanent third molars for the measurement of bond strength.
Record the type of substrate used.
For bovine teeth, use the labial surface. For human teeth, use the buccal, mesial, distal or lingual surface.
NOTE The occlusal surface of human teeth should not be used due to difficulty in finding a suitable bonding area.
Use superficial dentine, i.e. as close to enamel as possible, in order to reduce variations. It is important
that the planed dentine surface follow the anatomical plane of the dentine-enamel junction (interface)
as closely as possible in order to produce a uniform dentine structure.
4.2 Time after extraction
Use teeth within 6 months after extraction.
NOTE Teeth extracted more than 6 months prior to use may undergo degenerative changes in dentinal proteins.
4.3 Condition of teeth
Use caries-free teeth for bond strength measurement. Do not use human teeth which are restored or are
root-filled teeth (endodontically treated).
4.4 Initial preparation and storage of teeth
For bovine teeth, cut off the roots at the cemento-enamel junction (CEJ) and remove the pulp. For human
teeth, wash thoroughly in running water and remove all blood and adherent tissue as soon as possible
after extraction.
Place the teeth in water (ISO 3696, grade 3) at (4 ± 4)°C. To minimize deterioration, replace the storage
medium at least once every 2 months.
Preservatives which do not react with dentine, e.g. 1 % aqueous solution of chloramine-T, may be used.
Do not use preservatives which can react with dentine, e.g. aldehydes, or which can inhibit radical
polymerization, e.g. phenols. If storage in a preservative has taken place, thoroughly rinse the teeth in
running water to remove any preservative solution prior to tooth surface preparation.
5 Tooth surface preparation
5.1 General
A standard, reproducible, flat surface is required. Keep tooth surfaces wet at all times.
NOTE Exposure of a tooth surface to the air for several minutes may cause irreversible changes in bonding
character. Dentine is especially sensitive to dehydration.
5.2 Potting (mounting) of teeth
Prior to potting the teeth, block the opening to the pulp chamber with wax or dental cement. Alternatively, use
a high viscosity potting medium that does not penetrate the pulp chamber. This can be verified by preparing
a set of potted teeth, sectioning them and examining the pulp chambers. Discard the sectioned specimens.
Place the tooth bonding side down (labial side down for bovine teeth; buccal, mesial, distal or lingual
side down for human teeth) in a cylindrical mould on a level working surface. Plastics or metal rings
of approximately 25 mm internal diameter may be used. The height of the mould may vary; 10 mm to
25 mm is suggested. If rings are used, a sheet of polyester or similar film may be placed under the rings
for easy removal and clean up. Pour a mixed slow-setting viscous self-curing resin or dental die stone
into the mould. Remove the potted tooth from the mould as soon as possible after the potting medium
has set. Store
...
INTERNATIONAL ISO
STANDARD 29022
First edition
2013-06-01
Dentistry — Adhesion — Notched-
edge shear bond strength test
Médecine bucco-dentaire — Adhérence — Essai de résistance au
cisaillement sur échantillons à bord entaillé
Reference number
©
ISO 2013
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Tooth substrate and storage . 1
4.1 General . 1
4.2 Time after extraction . 2
4.3 Condition of teeth . 2
4.4 Initial preparation and storage of teeth . 2
5 Tooth surface preparation . 2
5.1 General . 2
5.2 Potting (mounting) of teeth . 2
5.3 Surface preparation . 3
5.4 Storage of prepared specimens . 3
6 Specimen production, handling and storage . 3
6.1 General . 3
6.2 Preconditioning . 3
6.3 Application of adhesive . 3
6.4 Insertion into bonding clamp . 4
6.5 Composite placement . 4
6.6 Specimen handling and storage . 4
7 Notched-edge shear test . 5
7.1 Apparatus . 5
7.2 Shear loading . 6
7.3 Test . 6
7.4 Recording and treatment of results . 6
7.5 Report . 6
Annex A (normative) Detailed drawings of notched-edge shear apparatus .8
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
ISO 29022 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 1, Filling and
restorative materials.
iv © ISO 2013 – All rights reserved
Introduction
The International Organization for Standardization (ISO) draws attention to the fact that it is claimed that
compliance with this document may involve the use of a patent concerning testing shear bond strength.
ISO takes no position concerning the evidence, validity and scope of this patent right.
The holder of this patent right has ensured ISO that he/she is willing to negotiate licenses under
reasonable and non-discriminatory terms and conditions with applicants throughout the world. In
this respect, the statement of the holder of this patent right is registered with ISO. Information may be
obtained from:
Neil T. Jessop, Ultradent Products, Inc., 505 West 10200 South, South Jordan, Utah 84095-3942, USA.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights other than those identified above. ISO shall not be held responsible for identifying any or
all such patent rights.
The purpose of this International Standard is to establish a simple and easy to use method for documenting
a claim that a material adheres to tooth substance. While the method described in this International
Standard has been used for comparing dental adhesive materials, users of this International Standard
should evaluate usefulness of this method for their particular application(s). There is a variety of other
dental adhesion test methods that may also be suitable or preferable, depending on the objective (e.g.
academic research).
INTERNATIONAL STANDARD ISO 29022:2013(E)
Dentistry — Adhesion — Notched-edge shear bond
strength test
1 Scope
This International Standard specifies a shear test method used to determine the adhesive bond strength
between direct dental restorative materials and tooth structure, e.g. dentine or enamel. The method as
described is principally intended for dental adhesives. The method includes substrate selection, storage
and handling of tooth structure, as well as the procedure for testing.
NOTE 1 Testing adhesion to tooth structure is technique sensitive and experience with the test method is required.
NOTE 2 With modification, it may be possible to use this method for adhesive restorative materials (e.g. glass-
ionomer materials).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 1942, Dentistry — Vocabulary
ISO 3696, Water for analytical laboratory use — Specification and test methods
ISO 6344−1, Coated abrasives — Grain size analysis — Part 1: Grain size distribution test
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1942 and the following apply.
3.1
bond strength
force per unit area required to break a bonded assembly with failure occurring in or near the
adhesive/adherend interface
3.2
direct dental restorative material
material used to restore a tooth that is placed in the plastic or unset state and sets intraorally when
used clinically
3.3
substrate
material upon the surface of which an adhesive is spread for any purpose, such as bonding or coating
4 Tooth substrate and storage
4.1 General
Use bovine incisors or human erupted permanent third molars for the measurement of bond strength.
Record the type of substrate used.
For bovine teeth, use the labial surface. For human teeth, use the buccal, mesial, distal or lingual surface.
NOTE The occlusal surface of human teeth should not be used due to difficulty in finding a suitable bonding area.
Use superficial dentine, i.e. as close to enamel as possible, in order to reduce variations. It is important
that the planed dentine surface follow the anatomical plane of the dentine-enamel junction (interface)
as closely as possible in order to produce a uniform dentine structure.
4.2 Time after extraction
Use teeth within 6 months after extraction.
NOTE Teeth extracted more than 6 months prior to use may undergo degenerative changes in dentinal proteins.
4.3 Condition of teeth
Use caries-free teeth for bond strength measurement. Do not use human teeth which are restored or are
root-filled teeth (endodontically treated).
4.4 Initial preparation and storage of teeth
For bovine teeth, cut off the roots at the cemento-enamel junction (CEJ) and remove the pulp. For human
teeth, wash thoroughly in running water and remove all blood and adherent tissue as soon as possible
after extraction.
Place the teeth in water (ISO 3696, grade 3) at (4 ± 4)°C. To minimize deterioration, replace the storage
medium at least once every 2 months.
Preservatives which do not react with dentine, e.g. 1 % aqueous solution of chloramine-T, may be used.
Do not use preservatives which can react with dentine, e.g. aldehydes, or which can inhibit radical
polymerization, e.g. phenols. If storage in a preservative has taken place, thoroughly rinse the teeth in
running water to remove any preservative solution prior to tooth surface preparation.
5 Tooth surface preparation
5.1 General
A standard, reproducible, flat surface is required. Keep tooth surfaces wet at all times.
NOTE Exposure of a tooth surface to the air for several minutes may cause irreversible changes in bonding
character. Dentine is especially sensitive to dehydration.
5.2 Potting (mounting) of teeth
Prior to potting the teeth, block the opening to the pulp chamber with wax or dental cement. Alternatively, use
a high viscosity potting medium that does not penetrate the pulp chamber. This can be verified by preparing
a set of potted teeth, sectioning them and examining the pulp chambers. Discard the sectioned specimens.
Place the tooth bonding side down (labial side down for bovine teeth; buccal, mesial, distal or lingual
side down for human teeth) in a cylindrical mould on a level working surface. Plastics or metal rings
of approximately 25 mm internal diameter may be used. The height of the mould may vary; 10 mm to
25 mm is suggested. If rings are used, a sheet of polyester or similar film may be placed under the rings
for easy removal and clean up. Pour a mixed slow-setting viscous self-curing resin or dental die stone
into the mould. Remove the potted tooth from the mould as soon as possible after the potting medium
has set. Store
...
NORME ISO
INTERNATIONALE 29022
Première édition
2013-06-01
Médecine bucco-dentaire —
Adhérence — Essai de résistance au
cisaillement sur échantillons à bord
entaillé
Dentistry — Adhesion — Notched-edge shear bond strength test
Numéro de référence
©
ISO 2013
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2013
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2013 – Tous droits réservés
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Référence normatives . 1
3 Termes et définitions . 1
4 Substrat dentaire et stockage . 2
4.1 Généralités . 2
4.2 Délai après extraction . 2
4.3 État des dents . 2
4.4 Préparation initiale et stockage des dents . 2
5 Préparation de la surface dentaire. 2
5.1 Généralités . 2
5.2 Enrobage des dents (montage) . 2
5.3 Préparation de la surface . 3
5.4 Stockage des spécimens préparés . 3
6 Production, conditionnement et stockage des spécimens . 4
6.1 Généralités . 4
6.2 Préconditionnement . 4
6.3 Application de l’adhésif . 4
6.4 Mise en place dans l’étrier de collage . 4
6.5 Mise en place du composite . 4
6.6 Conditionnement et stockage des spécimens . 5
7 Essai de cisaillement sur échantillons à bord entaillé . 5
7.1 Appareillage. 5
7.2 Charge de cisaillement . 6
7.3 Essai . 7
7.4 Enregistrement et traitement des résultats . 7
7.5 Rapport d’essai . 7
Annexe A (normative) Plans détaillés de l’échantillon de cisaillement à bord entaillé .8
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (CEI) en ce qui concerne
la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives
ISO/CEI, Partie 2.
La tâche principale des comités techniques est d’élaborer les Normes internationales. Les projets de
Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour vote.
Leur publication comme Normes internationales requiert l’approbation de 75 % au moins des comités
membres votants.
L’ISO 29022 a été élaborée par le Comité technique ISO/TC 106, Médecine bucco-dentaire, sous-comité
SC 1, Produits pour obturation et restauration.
iv © ISO 2013 – Tous droits réservés
Introduction
L’Organisation internationale de normalisation (ISO) souhaite indiquer qu’il est possible que la conformité
au présent document implique l’utilisation d’un brevet relatif aux essais de résistance au cisaillement.
L’ISO ne prend aucunement position concernant la réalité, la validité et le champ d’application de ce
droit de brevet.
Le titulaire de ce brevet a assuré à l’ISO qu’il était disposé à négocier les licences, dans des conditions
raisonnables et non discriminatoires, avec des demandeurs du monde entier. À cet égard, la déclaration
du titulaire de ce droit de brevet est enregistrée auprès de l’ISO. Les informations sont disponibles à
l’adresse suivante:
Neil T. Jessop, Ultradent Products, Inc., 505 West 10200 South, South Jordan, Utah 84095-3942, USA.
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence.
La présente Norme internationale a pour objectif d’établir une méthode simple et facile d’utilisation
pour produire une documentation justifiant l’adhérence d’un matériau à la substance dentaire. Bien
que la méthode décrite dans la présente Norme internationale a été utilisée pour comparer des adhésifs
à usage dentaire, il convient que les utilisateurs de la présente Norme internationale évaluent son
utilité par rapport à leur(s) application(s) particulière(s). Selon l’objectif visé (par exemple recherche
universitaire), il existe un large éventail d’autres méthodes d’essai d’adhérence dentaire qui pourront
s’avérer tout aussi adaptées ou préférables.
NORME INTERNATIONALE ISO 29022:2013(F)
Médecine bucco-dentaire — Adhérence — Essai de
résistance au cisaillement sur échantillons à bord entaillé
1 Domaine d’application
La présente Norme internationale spécifie une méthode d’essai de cisaillement qui permet de déterminer
la force d’adhérence entre les produits de restauration dentaire directe et la structure dentaire, par
exemple la dentine ou l’émail. La méthode décrite est principalement destinée aux adhésifs dentaires. La
méthode comprend le choix du substrat, le stockage et le conditionnement de la structure dentaire, ainsi
que le mode opératoire d’essai.
NOTE 1 Les essais d’adhérence à une structure dentaire sont sensibles à la technique utilisée et nécessitent
une certaine expérience de la méthode d’essai.
NOTE 2 Sous réserve de modification, cette méthode peut être utilisée pour des matériaux de restauration
adhésifs (par exemple ciments au verre ionomère).
2 Référence normatives
Les documents suivants, en totalité ou en partie, sont référencés de manière normative dans le présent
document et sont indispensables pour son application. Pour les références datées, seule l’édition citée
s’applique. Pour les références non datées, la dernière édition du document de référence s’applique (y
compris les éventuels amendements).
ISO 1942, Médecine bucco-dentaire — Vocabulaire
ISO 3696, Eau pour laboratoire à usage analytique — Spécification et méthodes d’essai
ISO 6344-1, Abrasifs appliqués — Granulométrie — Partie 1: Contrôle de la distribution granulométrique
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l’ISO 1942 ainsi que les
suivants s’appliquent.
3.1
force d’adhérence
force par surface unitaire requise pour rompre un assemblage collé, la rupture se produisant au niveau
ou à proximité de l’interface adhésif/support
3.2
matériau de restauration dentaire directe
matériau utilisé pour la restauration d’une dent inséré en phase plastique ou non activée et dont la prise
se réalise dans la cavité buccale lorsqu’il est utilisé cliniquement
3.3
substrat
matériau sur la surface duquel un adhésif est étalé pour toute opération, par exemple collage ou revêtement
4 Substrat dentaire et stockage
4.1 Généralités
Pour mesurer la force d’adhérence, utiliser des incisives de bovins ou des dents de sagesse humaines
ayant fait leur irruption. Noter le type de substrat utilisé.
Pour les dents de bovins, utiliser la face labiale. Pour les dents humaines, utiliser la face buccale, mésiale,
distale ou linguale.
NOTE Il convient de ne pas utiliser la face occlusale des dents humaines en raison de la difficulté à trouver
une surface de collage appropriée.
Pour réduire les variations, utiliser de la dentine superficielle, c’est-à-dire aussi proche que possible
de l’émail. Il est important que la surface de dentine aplanie suive le plan anatomique de la jonction
dentine-émail (interface) d’aussi près que possible afin d’obtenir une structure dentinaire uniforme.
4.2 Délai après extraction
Utiliser les dents dans un délai de 6 mois après l’extraction.
NOTE Les dents extraites plus de 6 mois avant leur utilisation peuvent subir des modifications dégénératives
de leurs protéines dentinaires.
4.3 État des dents
Pour mesurer la force d’adhérence, utiliser des dents non cariées. Ne pas utiliser de dents humaines
restaurées ou dont la racine a été obturée (ayant subi un traitement endodontique).
4.4 Préparation initiale et stockage des dents
Pour les dents de bovins, sectionner les racines au niveau de la jonction amélo-cémentaire (JAC) et
retirer la pulpe. Pour les dents humaines, laver soigneusement à l’eau courante et éliminer la totalité du
sang et du tissu adhérent dès que possible après l’extraction.
Placer les dents dans de l’eau (ISO 3696, qualité 3) à une température de (4 ± 4) °C. Pour réduire la
détérioration au minimum, renouveler le milieu de stockage au moins une fois tous les 2 mois.
Il est possible d’utiliser des agents conservateurs non susceptibles de réagir avec la dentine, par exemple
une solution aqueuse à 1 % de Chloramine-T. Ne pas utiliser d’agents conservateurs susceptibles de réagir
avec la dentine, par exemple aldéhydes, ou d’inhiber la polymérisation radicalaire, par exemple phénols).
En cas de stockage dans un agent conservateur, rincer soigneusement les dents à l’eau courante afin
d’éliminer toute la solution contenant l’agent conservateur avant la préparation de la surface dentaire.
5 Préparation de la surface dentaire
5.1 Généralités
Une surface plate, reproductible, normalisée est requise. Maintenir les surfaces dentaires humides
en permanence.
NOTE L’exposition d’une surface dentaire à l’air pendant plusieurs minutes peut engendrer des modifications
irréversibles des propriétés adhésives. La dentine est particulièrem
...
NORME ISO
INTERNATIONALE 29022
Première édition
2013-06-01
Médecine bucco-dentaire —
Adhérence — Essai de résistance au
cisaillement sur échantillons à bord
entaillé
Dentistry — Adhesion — Notched-edge shear bond strength test
Numéro de référence
©
ISO 2013
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2013
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2013 – Tous droits réservés
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Référence normatives . 1
3 Termes et définitions . 1
4 Substrat dentaire et stockage . 2
4.1 Généralités . 2
4.2 Délai après extraction . 2
4.3 État des dents . 2
4.4 Préparation initiale et stockage des dents . 2
5 Préparation de la surface dentaire. 2
5.1 Généralités . 2
5.2 Enrobage des dents (montage) . 2
5.3 Préparation de la surface . 3
5.4 Stockage des spécimens préparés . 3
6 Production, conditionnement et stockage des spécimens . 4
6.1 Généralités . 4
6.2 Préconditionnement . 4
6.3 Application de l’adhésif . 4
6.4 Mise en place dans l’étrier de collage . 4
6.5 Mise en place du composite . 4
6.6 Conditionnement et stockage des spécimens . 5
7 Essai de cisaillement sur échantillons à bord entaillé . 5
7.1 Appareillage. 5
7.2 Charge de cisaillement . 6
7.3 Essai . 7
7.4 Enregistrement et traitement des résultats . 7
7.5 Rapport d’essai . 7
Annexe A (normative) Plans détaillés de l’échantillon de cisaillement à bord entaillé .8
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (CEI) en ce qui concerne
la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives
ISO/CEI, Partie 2.
La tâche principale des comités techniques est d’élaborer les Normes internationales. Les projets de
Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour vote.
Leur publication comme Normes internationales requiert l’approbation de 75 % au moins des comités
membres votants.
L’ISO 29022 a été élaborée par le Comité technique ISO/TC 106, Médecine bucco-dentaire, sous-comité
SC 1, Produits pour obturation et restauration.
iv © ISO 2013 – Tous droits réservés
Introduction
L’Organisation internationale de normalisation (ISO) souhaite indiquer qu’il est possible que la conformité
au présent document implique l’utilisation d’un brevet relatif aux essais de résistance au cisaillement.
L’ISO ne prend aucunement position concernant la réalité, la validité et le champ d’application de ce
droit de brevet.
Le titulaire de ce brevet a assuré à l’ISO qu’il était disposé à négocier les licences, dans des conditions
raisonnables et non discriminatoires, avec des demandeurs du monde entier. À cet égard, la déclaration
du titulaire de ce droit de brevet est enregistrée auprès de l’ISO. Les informations sont disponibles à
l’adresse suivante:
Neil T. Jessop, Ultradent Products, Inc., 505 West 10200 South, South Jordan, Utah 84095-3942, USA.
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence.
La présente Norme internationale a pour objectif d’établir une méthode simple et facile d’utilisation
pour produire une documentation justifiant l’adhérence d’un matériau à la substance dentaire. Bien
que la méthode décrite dans la présente Norme internationale a été utilisée pour comparer des adhésifs
à usage dentaire, il convient que les utilisateurs de la présente Norme internationale évaluent son
utilité par rapport à leur(s) application(s) particulière(s). Selon l’objectif visé (par exemple recherche
universitaire), il existe un large éventail d’autres méthodes d’essai d’adhérence dentaire qui pourront
s’avérer tout aussi adaptées ou préférables.
NORME INTERNATIONALE ISO 29022:2013(F)
Médecine bucco-dentaire — Adhérence — Essai de
résistance au cisaillement sur échantillons à bord entaillé
1 Domaine d’application
La présente Norme internationale spécifie une méthode d’essai de cisaillement qui permet de déterminer
la force d’adhérence entre les produits de restauration dentaire directe et la structure dentaire, par
exemple la dentine ou l’émail. La méthode décrite est principalement destinée aux adhésifs dentaires. La
méthode comprend le choix du substrat, le stockage et le conditionnement de la structure dentaire, ainsi
que le mode opératoire d’essai.
NOTE 1 Les essais d’adhérence à une structure dentaire sont sensibles à la technique utilisée et nécessitent
une certaine expérience de la méthode d’essai.
NOTE 2 Sous réserve de modification, cette méthode peut être utilisée pour des matériaux de restauration
adhésifs (par exemple ciments au verre ionomère).
2 Référence normatives
Les documents suivants, en totalité ou en partie, sont référencés de manière normative dans le présent
document et sont indispensables pour son application. Pour les références datées, seule l’édition citée
s’applique. Pour les références non datées, la dernière édition du document de référence s’applique (y
compris les éventuels amendements).
ISO 1942, Médecine bucco-dentaire — Vocabulaire
ISO 3696, Eau pour laboratoire à usage analytique — Spécification et méthodes d’essai
ISO 6344-1, Abrasifs appliqués — Granulométrie — Partie 1: Contrôle de la distribution granulométrique
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l’ISO 1942 ainsi que les
suivants s’appliquent.
3.1
force d’adhérence
force par surface unitaire requise pour rompre un assemblage collé, la rupture se produisant au niveau
ou à proximité de l’interface adhésif/support
3.2
matériau de restauration dentaire directe
matériau utilisé pour la restauration d’une dent inséré en phase plastique ou non activée et dont la prise
se réalise dans la cavité buccale lorsqu’il est utilisé cliniquement
3.3
substrat
matériau sur la surface duquel un adhésif est étalé pour toute opération, par exemple collage ou revêtement
4 Substrat dentaire et stockage
4.1 Généralités
Pour mesurer la force d’adhérence, utiliser des incisives de bovins ou des dents de sagesse humaines
ayant fait leur irruption. Noter le type de substrat utilisé.
Pour les dents de bovins, utiliser la face labiale. Pour les dents humaines, utiliser la face buccale, mésiale,
distale ou linguale.
NOTE Il convient de ne pas utiliser la face occlusale des dents humaines en raison de la difficulté à trouver
une surface de collage appropriée.
Pour réduire les variations, utiliser de la dentine superficielle, c’est-à-dire aussi proche que possible
de l’émail. Il est important que la surface de dentine aplanie suive le plan anatomique de la jonction
dentine-émail (interface) d’aussi près que possible afin d’obtenir une structure dentinaire uniforme.
4.2 Délai après extraction
Utiliser les dents dans un délai de 6 mois après l’extraction.
NOTE Les dents extraites plus de 6 mois avant leur utilisation peuvent subir des modifications dégénératives
de leurs protéines dentinaires.
4.3 État des dents
Pour mesurer la force d’adhérence, utiliser des dents non cariées. Ne pas utiliser de dents humaines
restaurées ou dont la racine a été obturée (ayant subi un traitement endodontique).
4.4 Préparation initiale et stockage des dents
Pour les dents de bovins, sectionner les racines au niveau de la jonction amélo-cémentaire (JAC) et
retirer la pulpe. Pour les dents humaines, laver soigneusement à l’eau courante et éliminer la totalité du
sang et du tissu adhérent dès que possible après l’extraction.
Placer les dents dans de l’eau (ISO 3696, qualité 3) à une température de (4 ± 4) °C. Pour réduire la
détérioration au minimum, renouveler le milieu de stockage au moins une fois tous les 2 mois.
Il est possible d’utiliser des agents conservateurs non susceptibles de réagir avec la dentine, par exemple
une solution aqueuse à 1 % de Chloramine-T. Ne pas utiliser d’agents conservateurs susceptibles de réagir
avec la dentine, par exemple aldéhydes, ou d’inhiber la polymérisation radicalaire, par exemple phénols).
En cas de stockage dans un agent conservateur, rincer soigneusement les dents à l’eau courante afin
d’éliminer toute la solution contenant l’agent conservateur avant la préparation de la surface dentaire.
5 Préparation de la surface dentaire
5.1 Généralités
Une surface plate, reproductible, normalisée est requise. Maintenir les surfaces dentaires humides
en permanence.
NOTE L’exposition d’une surface dentaire à l’air pendant plusieurs minutes peut engendrer des modifications
irréversibles des propriétés adhésives. La dentine est particulièrem
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.