ISO 22915-2:2018

Industrial trucks — Verification of stability — Part 2: Counterbalanced trucks with mast

This document specifies the tests for verifying the stability of counterbalanced trucks with masts, equipped with fork arms or with load handling attachments. It is not applicable to those trucks designed for handling freight containers, dealt with by ISO 22915-9.

Chariots de manutention — Vérification de la stabilité — Partie 2: Chariots en porte-à-faux à mât

Le présent document spécifie les essais pour la vérification de la stabilité des chariots en porte-à-faux à mâts, équipés de bras de fourche ou d'équipements de manutention de charge. Il n'est pas applicable aux chariots conçus pour la manutention de conteneurs de fret, traités par l'ISO 22915‑9.

General Information

• Status: Published
• Publication Date: 18-Sep-2018
• ICS: 53.060 - Industrial trucks
• Technical Committee: ISO/TC 110/SC 2 - Safety of powered industrial trucks
• Drafting Committee: ISO/TC 110/SC 2/WG 11 - Stability
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 12-Feb-2024

Relations

• Revises: ISO 22915-2:2008 - Industrial trucks — Verification of stability — Part 2: Counterbalanced trucks with mast
• Effective Date: 15-Dec-2017

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 22915-2
Second edition
2018-09
Industrial trucks — Verification of
stability —
Part 2:
Counterbalanced trucks with mast
Chariots de manutention — Vérification de la stabilité —
Partie 2: Chariots en porte-à-faux à mât
Reference number
ISO 22915-2:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 22915-2:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 22915-2:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test conditions . 1
4.1 General . 1
4.2 Position of trucks and tilt table . 1
4.2.1 Load and steer axles . 1
4.2.2 Test 1 and 2 . . 2
4.2.3 Test 3 and 4 . . 2
4.3 Datum point positions . 5
4.4 Lift height for tests simulating travel. 5
5 Verification of stability . 5
5.1 General . 5
5.2 General Regional requirements for trucks with rated capacity ≥ 5 000 kg . 5
5.2.1 North America and Australia. 5
5.2.2 All other regions . 6
Bibliography . 7
© ISO 2018 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 22915-2:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of natio
...

ISO 22915-2:2018(E)
Deleted: /FDIS
ISO 22915-2:2018(E)
Deleted: /FDIS
2018-09
ISO TC 110/SC 02/WG 11
Secretariat: SIS
Industrial trucks – Verification of stability - Part 2: Counterbalanced trucks with mast

Deleted: FDIS stage
© ISO 2018 – All rights reserved

---------------------- Page: 1 ----------------------
ISO 22915-2:2018(E)
Deleted: /FDIS
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation,
no part of this publication may be reproduced or utilized otherwise in any form or by any means,
electronic or mechanical, including photocopying, or posting on the internet or an intranet,
without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH‐1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Deleted: www.iso.org
Published in Switzerland
2 © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 22915-2:2018(E)
Deleted: /FDIS
Contents
Foreword . 4
1  Scope . 5
2  Normative references . 5
3  Terms and definitions . 5
4  Test conditions . 5
4.1  General . 5
4.2  Position of trucks and tilt table . 5
4.2.1  Load and steer axles . 5
4.2.2  Test 1 and 2. 6
4.2.3  Test 3 and 4. 6
4.3  Datum point positions . 9
4.4  Lift height for tests simulating travel . 9
5  Verification of stability . 9
5.1  General . 9
5.2  General Regional requirements for trucks with rated capacity ≥ 5 000 kg . 9
5.2.1  North America and Australia . 9
5.2.2  All other regions . 9
Bibliography . 10
© ISO 2018 – All rights reserved 3

---------------------- Page: 3 ----------------------
ISO 22915-2:2018(E)
Deleted: /FDIS
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national
standards bodies (ISO member bodies). The work of preparing International Standards is normally
carried out through ISO technical committees. Each member body interested in a subject for which a
technical committee has been established has the right to be represented on that committee.
International organizations, governmental and non‐governmental, in liaison with ISO, also take part in
the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
The procedures used to develop this document and those intended for
...

NORME ISO
INTERNATIONALE 22915-2
Deuxième édition
2018-09
Chariots de manutention —
Vérification de la stabilité —
Partie 2:
Chariots en porte-à-faux à mât
Industrial trucks — Verification of stability —
Part 2: Counterbalanced trucks with mast
Numéro de référence
ISO 22915-2:2018(F)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 22915-2:2018(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2018
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: [phone]
Fax: [phone]
E-mail: [e-mail]
Web: www.iso.org
Publié en Suisse
ii © ISO 2018 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 22915-2:2018(F)

Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Conditions d'essai . 1
4.1 Généralités . 1
4.2 Position des chariots et de la plate-forme inclinable . 1
4.2.1 Essieux porteur et directeur . 1
4.2.2 Essai 1 et 2 . 2
4.2.3 Essai 3 et 4 . 2
4.3 Positions du point de référence . 5
4.4 Hauteur de levée pour les essais simulant le roulage . 5
5 Vérification de la stabilité . 5
5.1 Généralités . 5
5.2 Exigences régionales générales pour les chariots d’une capacité ≥ 5 000 kg . 6
5.2.1 Amérique du nord et Australie . 6
5.2.2 Toutes les autres régions . 6
Bibliographie . 7
© ISO 2018 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 22915-2:2018(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales e
...