ISO 2575:2010/Amd 6:2017

Road vehicles - Symbols for controls, indicators and tell-tales - Amendment 6

Véhicules routiers — Symboles pour les commandes, indicateurs et témoins — Amendement 6

General Information

• Status: Withdrawn
• Publication Date: 10-Aug-2017
• Withdrawal Date: 10-Aug-2017
• ICS: 01.080.20 - Graphical symbols for use on specific equipment
• ICS: 43.040.30 - Indicating and control devices
• Technical Committee: ISO/TC 22/SC 39 - Ergonomics
• Drafting Committee: ISO/TC 22/SC 39/WG 5 - Symbols
• Current Stage: 9599 - Withdrawal of International Standard
• Start Date: 07-Sep-2021
• Completion Date: 13-Dec-2025

Relations

• Amends: ISO 2575:2010 - Road vehicles - Symbols for controls, indicators and tell-tales
• Effective Date: 23-Apr-2020
• Revised: ISO 2575:2021 - Road vehicles - Symbols for controls, indicators and tell-tales
• Effective Date: 23-Apr-2020

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 2575
Eighth edition
2010-07-01
AMENDMENT 6
2017-08
Road vehicles — Symbols for controls,
indicators and tell-tales
AMENDMENT 6
Véhicules routiers — Symboles pour les commandes, indicateurs et
témoins
AMENDEMENT 6
Reference number
ISO 2575:2010/Amd.6:2017(E)
©
ISO 2017
ISO 2575:2010/Amd.6:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 2575:2010/Amd.6:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In
...

INTERNATIONAL ISO
STANDARD 2575
Eighth edition
2010-07-01
AMENDMENT 6
2017-08
Road vehicles — Symbols for controls,
indicators and tell-tales
AMENDMENT 6
Véhicules routiers — Symboles pour les commandes, indicateurs et
témoins
AMENDEMENT 6
Reference number
ISO 2575:2010/Amd.6:2017(E)
©
ISO 2017
ISO 2575:2010/Amd.6:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 2575:2010/Amd.6:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In
...