ISO 2632-2:1985
(Main)Roughness comparison specimens — Part 2: Spark-eroded, shot-blasted and grit-blasted, and polished
Roughness comparison specimens — Part 2: Spark-eroded, shot-blasted and grit-blasted, and polished
Échantillons de comparaison viso-tactile de rugosité — Partie 2: Électro-érosion, grenaillage sphérique et angulaire, et polissage
General Information
Relations
Buy Standard
Standards Content (Sample)
International Standard @ 263212
INTF RNATIONAL ORGANIZATION FOR STANOARDIZATIONDMEMnYHAPO~HAA OPrAHHJAUMR no CTAH~APTH3AUMH.ORGANlSATlON INTERNATIONALE DE NORMALISATION
a
Roughness comparison specimens -
Part 2: Spark-eroded, shot-blasted and grit-blasted, and
polished
Échantillons de comparaison Viso-tactile de rugosité - Partie 2: Électro-érosion, grenaillage sphérique et angulaire, et polissage
Second edition - 1985-11-15
- ” UDC 620.179.118 Ref. No. IS0 2632/2-1985 (E)
8
s
Descriptors : surface condition, roughness, roughness measurement, reference sample, Viso-tactile comparison specimens, specifications,
2 dimensions, marking.
w
Price based on 4 pages
s
---------------------- Page: 1 ----------------------
Foreword
IS0 (the International Organization for Standardization) is a worldwide federation of
national standards bodies (IS0 member bodies). The work of preparing International
Standards is normally carried out through IS0 technical committees. Each member
body interested in a subject for which a technical committee has been established has
e
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with 60, also take part in the work.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the IS0 Council. They are approved in accordance with IS0 procedures requiring at
least 75 % approval by the member bodies voting.
Y
International Standard IS0 2632/2 was prepared by Technical Committee ISO/TC 57,
Metrology and properties of suriaces.
IS0 2632/2 was first published in 19n. This second edition cancels and replaces the
first edition which has been revised as follows:
- new values have been added to tables 1 and 2;
- clause 8 has been expanded:
- a new clause (clause 9 “Minimum specimen size”) has been added;
- table 5 has been deleted;
- references and editorial presentation have been updated.
Users should note that all International Standards undergo revision from time to time
and that any reference made herein to any other International Standard implies its
latest edition, unless otherwise stated.
---------------------- Page: 2 ----------------------
INTERNATIONAL STANDARD IS0 2632/2-1985 (E)
Roughness comparison specimens -
Part 2 : Spark-eroded, shot-blasted and grit-blasted, and
polished
0 1 Scope and field of application and appearance of the particular production process and
roughness grade, and to enable workshop personnel to
This part of IS0 2632 specifies the characteristics of specimens evaluate and control workpiece surfaces by tactile and visual
of spark-eroded, shot-blasted and grit-blasted, and polished comparison with the specimen surface.
surfaces which are intended for tactile and visual comparison
with workpiece surfaces of similar lay, produced by similar
3.2 lay: The direction of the predominant surface pattern,
manufacturing methods.
ordinarily determined by the process used in producing the sur-
face.
It is complementary to IS0 263211 and IS0 263213.
Other terms used to describe surface characteristics or measu-
1
rement are defined in IS0 428711.
2 References
IS0 3, Preferred numbers - Series of preferred numbers.
4 Methods of manufacture
IS0 468, Surface roughness - Parameters, their values and
The specimens shall be manufactured as follows:
general rules for specifying requirements.
a) by electro-forming positive replicas of master surfaces;
IS0 1302, Technical drawings - Method of indicating surface
texture on drawings.
b) by making positive replicas in plastics or other materials
of master surfaces which represent the feel and appearance
IS0 1880, Instruments for the measurement of surface rough-
of the natural manufactured surface;
0 ness by the profile method - Contact (stylus) instruments of
progressive profile transformation - Profile recording instru-
c) by direct application of the production process which
ments.
the specimen is intended to represent (individually manufac-
tured specimens).
IS0 263211, Roughness comparison specimens - Part I:
Turned, ground, bored, milled, shaped and planed.
5 Surface characteristics
IS0 263213, Roughness comparison specimens - Part3: Cast
surfaces.
Master surfaces for reproduction or their replicas, and in-
dividually manufactured specimens (see clause 4) shall exhibit
IS0 3274, Instruments for the measurement of surface
only the characteristics resulting from the natural action of the
roughness by the profile method - Contact istylusl instru-
manufacturing process which they are intended to represent.
ments of consecutive profile transformation - Contact profile
meters, system M.
6 Ranges of roughness grades
IS0 428711, Surface roughness - Terminology - Part I: Sur-
face and its parameters.
The ranges of roughness grades shall be as given in table
...
,*xi+
rrne internationale @ 2632’2
illons de comparaison Viso-tactile de rugosité -
: Électro-érosion, grenaillage sphérique
laire, et polissage
rison specimens - Part 2: Spark-eroded, shot-blasted and grit-blasted, and polished
ion - 1985-11-15
-
Réf. no : IS0 2632/2-1985 (<
CDU i20.179.118
!
3urs : état de surface, rugosité, mesurage de rugosité, échantillon témoin, échantillon comparaison Viso-tactile, spécification,
Descripl
*
dimensio I, marquage.
8
Prix basé sur 4 pages
---------------------- Page: 1 ----------------------
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale
d'organismes nationaux de normalisation (comités membres de I'ISO). L'élaboration
des Normes internationales est confiée aux comités techniques de I'ISO. Chaque
comité membre intéressé par une étude a le droit de faire partie du comité technique
créé à cet effet. Les organisations internationales, gouvernementales et non gouverne-
mentales, en liaison avec 1'1S0 participent également aux travaux.
Les projets de Normes internationales adoptés par les comités techniques sont soumis
aux comités membres pour approbation, avant leur acceptation comme Normes inter-
nationales par le Conseil de I'ISO. Les Normes internationales sont approuvées confor-
mément aux procédures de 1'1S0 qui requièrent l'approbation de 75 % au moins des
Comités membres votants.
La Norme internationale IS0 2632/2 a été élaborée par le comité technique ISO/TC 57,
Métrologie et propriétés des surfaces.
La Norme internationale 2632/2 a été pour la première fois publiée en 1977. Cette
deuxième édition annule et remplace la première édition qui a été modifiée comme suit:
- de nouvelles valeurs ont été ajoutées dans les tableaux 1 et 2;
- le chapitre 8 a été complété;
-
un nouveau chapitre (chapitre 9 ((Dimensions minimales des échantillons») a
été ajouté;
- le tableau 5 a été supprimé;
- la présentation a été revue.
L'attention des utilisateurs est attirée sur le fait que toutes les Normes internationales
sont de temps en temps soumises à révision et que toute référence faite à une autre
Norme internationale dans le présent document implique qu'il s'agit, sauf indication
contraire, de la dernière édition.
O Organisation internationale de normalisation. 1985 0
Imprimé en Suisse
---------------------- Page: 2 ----------------------
IS0 2632/2-1985 (FI
maine d'application l'aspect que donnent un procédé de fabrication et un degré de
rugosité particuliers, et permet au personnel des ateliers d'éva-
luer et de vérifier les surfaces des pièces usinées par comparai-
son Viso-tactile avec la surface échantillon.
3.2 stries: Sens du dessin prédominant sur la surface, géné-
blables et qui sont produites par des modes
ralement déterminé par le procédé utilisé pour la production de
la surface.
Les autres termes utilisés pour décrire les caractéristiques ou le
mesurage des surfaces sont définis dans I'ISO 4287/1.
4 Procédés de fabrication
res normaux - Séries de nombres normaux.
Les échantillons doivent être fabriqués selon les procédés sui-
vants:
reproductions positives obtenues par électro-formage à
a)
- Indication des états de sur- partir de matrices;
sins techniques
b) reproductions positives à partir de matrices en plasti-
que, ou en d'autres matériaux, donnant des surfaces qui ont
le même toucher et le même aspect qu'une surface produite
naturellement:
c) application directe du procédé de fabrication que
l'échantillon est censé représenter (échantillons produits
individuellement).
I: Tournage, rectification, alésage, fraisage, rabo-
5 Caractéristiques des surfaces
3: Surfaces moulées.
Les matrices servant à la reproduction ou leurs reproductions et
les échantillons produits individuellement (voir chapitre 41, ne
doivent présenter que les caractéristiques résultant de l'action
du profil - Instruments à palpeur-aiguille, à
normale du procédé d'usinage qu'ils sont censés représenter.
rogressive du profil - ProfiIomètres à contact
6 Série de valeurs de rugosité
Les séries de valeurs de rugosité sont données dans le
tableau 1.
7 Longueurs de base
on de paramètre de rugosité superficiel connu Les longueurs de base données dans le tableau 2 sont à utiliser
un usinage particulier ou d'autres procédés de pour l'évaluation des échantillons. Dans le cas de profils répéti-
hantillon sert de référence au personnel des
tifs, la longueur de base doit être arrondie du nombre entier
supérieur de cycles le plus proche.
1
---------------------- Page: 3 ----------------------
IS0 2632/2-1985 (FI
Tableau 1 - Séries de valeurs de rugosité des échantillons de comparaison de rugosité
Procédés de fabrication
électro-érosion grenaillage sphérique et angulaire
I I polissage
Écarts moye
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.