ISO 4065:2018
(Main)Thermoplastics pipes — Universal wall thickness table
Thermoplastics pipes — Universal wall thickness table
ISO 4065:2018 specifies the relationship between the nominal wall thickness en and the nominal outside diameter dn of thermoplastics pipes. ISO 4065:2018 is applicable to solid-wall thermoplastics pipes of constant circular cross-section along the whole length of the pipe, whatever their method of manufacture, their composition or their intended application. NOTE Pipes with constant circular cross-section along the whole length of the pipe are commonly known as pipes with smooth external and internal surfaces.
Tubes en matières thermoplastiques — Tableau universel des épaisseurs de paroi
Plastomerne cevi - Preglednica univerzalne debeline stene
Ta dokument določa odnos med nominalno debelino stene (en) in nominalnim zunanjim premerom (dn) plastomernih cevi.
Uporablja se za plastomerne cevi s trdnimi stenami s stalnim krožnim prerezom po celotni dolžini cevi, ne glede na način njihove izdelave, njihovo sestavo ali predvideno uporabo.
OPOMBA: Cevi s stalnim krožnim prerezom po celotni dolžini cevi so splošno znane kot cevi z gladkimi zunanjimi in notranjimi površinami.
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 4065:2018
01-september-2018
1DGRPHãþD
SIST ISO 4065:2012
Plastomerne cevi - Preglednica univerzalne debeline stene
Thermoplastics pipes -- Universal wall thickness table
Tubes en matières thermoplastiques -- Tableau universel des épaisseurs de paroi
Ta slovenski standard je istoveten z: ISO 4065:2018
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
SIST ISO 4065:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 4065:2018
---------------------- Page: 2 ----------------------
SIST ISO 4065:2018
INTERNATIONAL ISO
STANDARD 4065
Third edition
2018-01
Thermoplastics pipes — Universal
wall thickness table
Tubes en matières thermoplastiques — Tableau universel des
épaisseurs de paroi
Reference number
ISO 4065:2018(E)
©
ISO 2018
---------------------- Page: 3 ----------------------
SIST ISO 4065:2018
ISO 4065:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 4065:2018
ISO 4065:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Calculation of values . 2
4.1 Calculation of S values . 2
4.2 Calculation of wall thicknesses . 3
5 Wall thickness tables . 5
6 Deviations . 5
Bibliography .10
© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 4065:2018
ISO 4065:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was
...
INTERNATIONAL ISO
STANDARD 4065
Third edition
2018-01
Corrected version
2019-12
Thermoplastics pipes — Universal
wall thickness table
Tubes en matières thermoplastiques — Tableau universel des
épaisseurs de paroi
Reference number
ISO 4065:2018(E)
©
ISO 2018
---------------------- Page: 1 ----------------------
ISO 4065:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 4065:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Calculation of values . 2
4.1 Calculation of S values . 2
4.2 Calculation of wall thicknesses . 3
5 Wall thickness tables . 5
6 Deviations . 5
Bibliography .10
© ISO 2018 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 4065:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on t
...
SLOVENSKI STANDARD
oSIST ISO 4065:2018
01-julij-2018
Plastomerne cevi - Preglednica univerzalne debeline stene
Thermoplastics pipes -- Universal wall thickness table
Tubes en matières thermoplastiques -- Tableau universel des épaisseurs de paroi
Ta slovenski standard je istoveten z: ISO 4065:2018
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
oSIST ISO 4065:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST ISO 4065:2018
---------------------- Page: 2 ----------------------
oSIST ISO 4065:2018
INTERNATIONAL ISO
STANDARD 4065
Third edition
2018-01
Thermoplastics pipes — Universal
wall thickness table
Tubes en matières thermoplastiques — Tableau universel des
épaisseurs de paroi
Reference number
ISO 4065:2018(E)
©
ISO 2018
---------------------- Page: 3 ----------------------
oSIST ISO 4065:2018
ISO 4065:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST ISO 4065:2018
ISO 4065:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Calculation of values . 2
4.1 Calculation of S values . 2
4.2 Calculation of wall thicknesses . 3
5 Wall thickness tables . 5
6 Deviations . 5
Bibliography .10
© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST ISO 4065:2018
ISO 4065:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordanc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.