iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 13966:1998

(Main)

Thermoplastics pipes and fittings — Nominal ring stiffnesses

Thermoplastics pipes and fittings — Nominal ring stiffnesses

Tubes et raccords en matières thermoplastiques — Rigidité annulaire nominale

General Information

Status
Published
Publication Date
08-Jul-1998
ICS
23.040.20 - Plastics pipes
23.040.45 - Plastics fittings
Technical Committee
ISO/TC 138 - Plastics pipes, fittings and valves for the transport of fluids
Drafting Committee
ISO/TC 138 - Plastics pipes, fittings and valves for the transport of fluids
Current Stage
9020 - International Standard under periodical review
Start Date
15-Apr-2024
Completion Date
15-Apr-2024
Ref Project

Buy Standard

ISO 13966:1998 - Thermoplastics pipes and fittings -- Nominal ring stiffnessesISO 13966:1998 - Thermoplastics pipes and fittings -- Nominal ring stiffnesses
PreviousNext
Standard
ISO 13966:1998 - Thermoplastics pipes and fittings -- Nominal ring stiffnesses
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
ISO 13966:1998 - Tubes et raccords en matieres thermoplastiques -- Rigidité annulaire nominaleISO 13966:1998 - Tubes et raccords en matieres thermoplastiques -- Rigidité annulaire nominale
PreviousNext
Standard
ISO 13966:1998 - Tubes et raccords en matieres thermoplastiques -- Rigidité annulaire nominale
French language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 13966
First edition
1998-07-15
Thermoplastics pipes and fittings —
Nominal ring stiffnesses
Tubes et raccords en matières thermoplastiques — Rigidité annulaire
nominale
A
Reference number
ISO 13966:1998(E)

---------------------- Page: 1 ----------------------
ISO 13966:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 13966 was prepared by Technical Committee
ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids.
©  ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii

---------------------- Page: 2 ----------------------
©
INTERNATIONAL STANDARD  ISO ISO 13966:1998(E)
Thermoplastics pipes and fittings — Nominal ring
stiffnesses
1 Scope
This international Standard specifies a range of nominal ring stiffness classes. It is applicable to components of
thermoplastics pipe systems having a circular cross-section.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
Intern
...

NORME ISO
INTERNATIONALE 13966
Première édition
1998-07-15
Tubes et raccords en matières
thermoplastiques — Rigidité annulaire
nominale
Thermoplastics pipes and fittings — Nominal ring stiffnesses
A
Numéro de référence
ISO 13966:1998(F)

---------------------- Page: 1 ----------------------
ISO 13966:1998(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération
mondiale d'organismes nationaux de normalisation (comités membres de
l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une
étude a le droit de faire partie du comité technique créé à cet effet. Les
organisations internationales, gouvernementales et non gouvernementales,
en liaison avec l'ISO, participent également aux travaux. L'ISO collabore
étroitement avec la Commission électrotechnique internationale (CEI) en
ce qui concerne la normalisation électrotechnique.
Les projets de Normes internationales adoptés par les comités techniques
sont soumis aux comités membres pour vote. Leur publication comme
Normes internationales requiert l'approbation de 75 % au moins des
comités membres votants.
La Norme internationale ISO 13966 a été élaborée par le comité technique
ISO/TC 138,Tubes, raccords et robinetterie en matières plastiques pour le
transport des fluides.
©  ISO 1998
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publi-
cation ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun pro-
cédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord
écrit de l'éditeur.
Organisation internationale de normalisation
Case postale 56 • CH-1211 Genève 20 • Suisse
Internet iso@iso.ch
Imprimé en Suisse
ii

---------------------- Page: 2 ----------------------
©
NORME INTERNATIONALE  ISO ISO 13966:1998(F)
Tubes et raccords en matières thermoplastiques — Rigidité
annulaire nominale
1 Domaine d’application
La présente Norme internationale spécifie la gamme des valeurs nominales de la rigidité annulaire.
Elle est applicable aux composants des systèmes de canalisations de section circulaire, en matières
thermoplastiques.
2 Références normatives
Les normes suivantes contiennent des dispositions qui, par suite de la référence qui en est faite, constituent des
dispositions valables pour la présente Norme internationale. Au mome
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 10928:2024(Main)
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use

This document specifies procedures suitable for the analysis of data which, when converted into logarithms of the values, have either a normal or a skewed distribution. It is intended for use with test methods and referring standards for glass-reinforced thermosetting plastics (GRP) pipes or fittings for the analysis of properties as a function of time. However, it can also be used for the analysis of other data. Two methods are specified, which are used depending on the nature of the data. Extrapolation using these techniques typically extends a trend from data gathered over a period of approximately 10 000 h to a prediction of the property at 50 years, which is the typical maximum extrapolation time. This document only addresses the analysis of data. The test procedures for collecting the data, the number of samples required and the time period over which data are collected are covered by the referring standards and/or test methods. Clause 6 discusses how the data analysis methods are applied to product testing and design.

  • Standard
    19 pages
    English language
    sale 15% off
ISO
ISO 16422-2:2024(Main)
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 2: Pipes

This document specifies the characteristics of solid-wall pipes made of oriented unplasticized poly(vinyl chloride) (PVC-O) for piping systems intended to be used underground or above-ground (where protected from direct sunlight), for water supply, buried drainage, sewerage, treated wastewater and irrigation under pressure. It also specifies the test parameters for the test methods referred to in this document. In conjunction with ISO 16422-1 and ISO 16422-5, this document is applicable to oriented PVC-O pipes, with or without integral socket, intended to be used for the following: a) water mains and services lines; b) conveyance of water for both outside and inside buildings; c) drainage, sewerage and treated wastewater under pressure; d) irrigation under pressure. This document is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for wastewater under pressure. This document is also applicable to components for the conveyance of water and wastewater up to and including 45 °C. For temperatures between 25 °C and 45 °C, see Figure C.1. The piping system according to this document is intended for the conveyance of cold water up to pressures of 25 bar[1] and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations, up to pressure of 25 bar. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2

  • Standard
    25 pages
    English language
    sale 15% off
ISO
ISO 16422-5:2024(Main)
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 5: Fitness for purpose of the system

This document specifies the characteristics of the fitness for purpose of oriented unplasticized poly(vinyl chloride) (PVC-O) solid wall piping intended to be used underground or above-ground where protected from direct sunlight, for water supply, buried drainage, sewerage, treated wastewater and irrigation under pressure. It also specifies the test parameters for the test methods referred to in this document. This document is not intended for on-site testing of pipe systems. In conjunction with ISO 16422-1, ISO 16422-2, ISO/TS 16422-3 and ISO 1452-3, this document is applicable to PVC-O pipes and PVC-O fittings, as well as to their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following: a) water mains and services lines; b) conveyance of water for both outside and inside buildings; c) drainage, sewerage and treated wastewater under pressure; d) irrigation under pressure. This document is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for wastewater under pressure. This document is also applicable to components for the conveyance of water and wastewater up to and including 45 °C. For temperatures between 25 °C and 45 °C, see ISO 16422-2:2023, Figure C.1. The piping system according to this document is intended for the conveyance of cold water up to pressures of 25 bar[1] and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations, up to pressure of 25 bar. [1] 1 bar= 0,1 MPa = 105 Pa; 1 MPa= 1 N/mm2

  • Standard
    11 pages
    English language
    sale 15% off
ISO
ISO 16422-1:2024(Main)
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 1: General

This document specifies the general characteristics of solid-wall pipes made of oriented unplasticized poly(vinyl chloride) (PVC-O) for piping systems intended to be used underground or above-ground (where protected from direct sunlight), for water supply, buried drainage, sewerage, treated waste water and irrigation under pressure. In conjunction with ISO 16422-2, ISO/TS 16422-3, ISO 16422-5 and ISO 1452-4, this document is applicable to PVC-O pipes and PVC-O fittings, as well as to valves, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following: a) water mains and services lines; b) conveyance of water for both outside and inside buildings; c) drainage, sewerage and treated wastewater under pressure; d) irrigation under pressure. This document is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for wastewater under pressure. This document is also applicable to components for the conveyance of water and wastewater up to and including 45 °C. For temperatures between 25 °C and 45 °C, see ISO 16422-2:2023, Figure C.1. The piping system according to this document is intended for the conveyance of cold water up to pressures of 25 bar[1] and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations, up to pressure of 25 bar. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2

  • Standard
    8 pages
    English language
    sale 15% off
ISO
ISO 4982:2023(Main)
Plastics piping systems for non-pressure underground conveyance and storage of non-potable water — Arch-shaped, corrugated wall chambers made of PE or PP used for retention, detention, storage and transportation of storm water systems — Product specifications and performance criteria

This document gives the definitions and specifies the minimum requirements for injection moulded and thermoformed thermoplastics corrugated arch-shaped chambers, including integral components, used in underground systems for retention, detention, transportation and storage of non-potable water (e.g. storm water) and manufactured from polyethylene (PE) or polypropylene (PP). These chambers are intended for buried underground use in one horizontal layer, e.g. in landscape, pedestrian or vehicular traffic areas. In the case of retention and detention systems, the main purpose of the chambers is to retain water, for later infiltration in the ground or for later use in non-potable applications (irrigation, cleaning, sanitary facilities, etc.) or to detain water during a storm, transferring it in a controlled way to the public storm water network. Applications include commercial, residential, agricultural and highway drainage, including installation under parking lots and roadways. Product performance is determined by a combination of material specification, product design and manufacturing process. These chambers are intended to be used as elements in a modular system where the manufacturer has provided a clearly documented method specifying how the components are assembled to create a complete retention, detention, storage or transportation system.

  • Standard
    36 pages
    English language
    sale 15% off
ISO
ISO 11296-9:2022(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 9: Lining with a rigidly anchored plastics inner layer

This document, in conjunction with ISO 11296‑1, specifies the requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout. This document is applicable to plastics inner layers and grout systems with or without steel reinforcement. It does not apply to the structural design of the lining system. NOTE Systems with multiple annuli are available, but these are controlled by patent rights and not covered by this document.

  • Standard
    29 pages
    English language
    sale 15% off
  • Standard
    31 pages
    French language
    sale 15% off
ISO
ISO 13267:2022(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics inspection chamber and manhole bases — Test methods for buckling resistance

This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    10 pages
    French language
    sale 15% off
  • Standard
    10 pages
    French language
    sale 15% off
ISO
ISO 13268:2022(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of ring stiffness

This document specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off
ISO
ISO 13266:2022(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of resistance against surface and traffic loading

This document specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading. It is not applicable to requirements for testing the cover and frame. Those requirements are specified in EN 124-1 or other standards, depending on the material. NOTE Upper assembly components normally include shafts or risers, cones, telescopic adapters and near surface components.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
ISO
ISO/TR 10358:2021(Main)
Plastics pipes and fittings for industrial applications — Collection of data on combined chemical-resistance

This document collects available data on combined chemical resistance of thermoplastic materials typically used to manufacture piping components for industrial applications, against fluids over a range of temperatures. The base thermoplastic materials covered by this classification are: Polyethylene PE NOTE 1 The PE considered in this document corresponds to PE-HD, with a minimum density value of 0,935 g/cm3 (e.g.: PE63, PE80, PE100, PE100-RC, PE-RT). Polypropylene PP (PP-R and PP-RCT, PP-H, PP-B) Polyvinyl chloride, unplasticized PVC-U Polyvinyl chloride, chlorinated PVC-C Polybutylene PB Acrylonitrile/butadiene/styrene ABS Polyvinylidene fluoride PVDF NOTE 2 This document considers homopolymer PVDF. Cross-linked polyethylene PE-X (PE-Xa, PE-Xb, PE-Xc) Ethylene chloro trifluoro ethylene ECTFE Polyamide, unplasticized PA-U (PA-U11, PA-U12) NOTE 3 This document focuses on PA-U11 and PA-U12 only, as these long chained PA-U are standardized according to ISO 16486-1; short chained (e.g. PA 66) and plasticized PAs are not used for monolithic plastic piping components. Polysulfone PSU Perfluoralkoxy PFA NOTE 4 Temperatures higher than 200°C can be applied after an evaluation with the raw material manufacturer. Polytetrafluoroethylene PTFE NOTE 5 Temperatures higher than 200°C can be applied after an evaluation with the raw material manufacturer. Polyphenylene sulphide PPS NOTE 6 PPS is new with regards to industrial application and chemical resistance issues; for this reason, manufacturers and end-users are advised to assess the chemical suitability of the material.

  • Technical report
    215 pages
    English language
    sale 15% off