ISO/TR 20174:2005

Welding — Grouping systems for materials — Japanese materials

ISO 20174:2005 provides a Japanese grouping system for materials for welding purposes, classified in accordance with the grouping system of ISO/TR:15608:2000.

Soudage — Systèmes de groupement des matériaux — Matériaux japonais

General Information

• Status: Withdrawn
• Publication Date: 06-Dec-2005
• Withdrawal Date: 06-Dec-2005
• ICS: 25.160.20 - Welding consumables
• Technical Committee: ISO/TC 44/SC 10 - Quality management in the field of welding
• Drafting Committee: ISO/TC 44/SC 10 - Quality management in the field of welding
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 19-Jun-2020

Relations

• Revised: ISO/TR 20174:2020 - Welding — Grouping systems for materials — Japanese materials
• Effective Date: 23-Apr-2020
• Consolidates: ISO/IEC 8473-4:1995 - Information technology — Protocol for providing the connectionless-mode network service: Provision of the underlying service by a subnetwork that provides the OSI data link service
• Effective Date: 06-Jun-2022

Standards Content (Sample)

TECHNICAL ISO/TR
REPORT 20174
First edition
2005-12-15

Welding — Grouping systems for
materials — Japanese materials
Soudage — Systèmes de groupement des matériaux — Matériaux
japonais




Reference number
ISO/TR 20174:2005(E)
©
ISO 2005

---------------------- Page: 1 ----------------------
ISO/TR 20174:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TR 20174:2005(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Japanese grouping system for materials. 2
2.1 Types of steels in accordance with the grouping system of ISO/TR 15608:2000, Table 1 . 2
2.2 Types of aluminium and aluminium alloys in accordance with the grouping system of
ISO/TR 15608:2000, Table 2 . 16
2.3 Types of titanium and titanium alloys in accordance with the grouping system of
ISO/TR 15608:2000, Table 5 . 21
Bibliography . 25

© ISO 2005 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/TR 20174:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In exceptional circumstances, when a technical committee has collected data of a different kind from that
which is normally published as an International Standard (“state of the art”, for example), it may decide by a
simple majority vote of its participating members to publish a Technical Report. A Technical Report is entirely
informative in nature and does not have to be reviewed until the data it provides are considered to be no
longer valid or useful.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TR 20174 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 121, Welding, in collaboration with Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).

iv © ISO 2005 – All rights reserved

---------------------- Page: 4 ----------------------
TECHNICAL REPORT ISO/TR 20174:2005(E)

Welding — Grouping systems for materials — Japanese
materials
1 Scope
This Technical Report provides a Japanese grouping system for materials for welding purposes, classified in
accordance with the grouping system of ISO/TR:15608.
It may also apply for other purposes, such as heat treatment, forming, and non-destructive testing.
This Technical Report covers grouping systems for the following standardized materials:
⎯ steel;
⎯ aluminium and its alloys;
⎯ titanium and its alloys.
© ISO 2005 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO/TR 20174:2005(E)
2 Japanese grouping system for materials
2.1 Types of steels in accordance with the grouping system of ISO/TR 15608:2000, Table 1
See Table 1.
Table 1 — Japanese grouping system for steels
Group Reference standard Designation
JIS G 3101 SS330
SS400
JIS G 3103 SB410
SB450
SB480
SB450M
SB480M
JIS G 3106 SM400A
SM400B
SM400C
JIS G 3113 SAPH310
JIS G 3116 SG255
JIS G 3115 SPV235
JIS G 3118 SGV410
SGV450
SGV480
JIS G 3126 SLA235A
SLA235B
1.1
JIS G 3131 SPHC
SPHD
SPHE
JIS G 3135 SPFC340
SPFC370
SPFC390
SPFC440
SPFC490Y
SPFC540Y
SPFC590Y
SPFC340H
JIS G 3136 SN400A
SN400B
SN400C
JIS G 3444 STK290
STK400
STK500
STK490
2 © ISO 2005 – All rights reserved

---------------------- Page: 6 ----------------------
ISO/TR 20174:2005(E)
Table 1 (continued)
Group Reference standard Designation
JIS G 3452 SGP
JIS G 3454 STPG370
STPG410
JIS G 3455 STS370
STS410
STS480
JIS G 3456 STPT370
STPT410
STPT480
JIS G 3457 STPY400
JIS G 3458 STPA12
JIS G 3460 STPL380
JIS G 3461 STB340
STB410
JIS G 3462 STBA12
1.1
STBA13
JIS G 3464 STBL380
JIS G 3467 STF410
STFA12
JIS G 3472 STAM290GA
STAM290GB
STAM340G
STAM390G
JIS G 3473 STC370
JIS G 3475 STKN400W
STKN400B
JIS G 3201 SF340A
SF390A
SF440A
SF490A
SF540A
© ISO 2005 – All rights reserved 3

---------------------- Page: 7 ----------------------
ISO/TR 20174:2005(E)
Table 1 (continued)
Group Reference standard Designation
JIS G 3202 SFVC1
SFVC2A
SFVC2B
1.1
JIS G 3203 SFVAF1
JIS G 3205 SFL1
SFL2
JIS G 3101 SS490
JIS G 3106 SM490A
SM490B
SM490C
SM490YA
SM490YB
JIS G 3115 SPV315
SPV355
JIS G 3116 SG295
SG325
JIS G 3119 SBV1A
SBV1B
SBV2
1.2 JIS G 3120 SQV1A
SQV2A
JIS G 3126 SLA325A
SLA325B
JIS G 3134 SPFH490
SPFH540
SPFH540Y
SPFH590Y
JIS G 3135 SPFC490
SPFC540
SPFC590
JIS G 3136 SN490B
SN490C
JIS G 3461 STB510
4 © ISO 2005 – All rights reserved

---------------------- Page: 8 ----------------------
ISO/TR 20174:2005(E)
Table 1 (continued)
Group Reference standard Designation
JIS G 3472 STAM440G
STAM470G
STAM500G
STAM440H
JIS G 3473 STC440
1.2
JIS G 3475 STKN490B
JIS G 3201 SF540B
SF590A
SF590B
JIS G 3204 SFVQ1A
JIS G 3106 SM520BN
SM520CN
JIS G 3113 SAPH370
SAPH400
SAPH440
1.3
JIS G 3115 SPV450N
SPV490N
JIS G 3124 SEV245N
SEV295N
SEV345N
JIS G 3114 SMA400AW
SMA400AP
SMA400BW
SMA400BP
SMA400CW
SMA400CP
1.4
SMA490AW
SMA490AP
SMA490BW
SMA490BP
SMA490CW
SMA490CP
© ISO 2005 – All rights reserved 5

---------------------- Page: 9 ----------------------
ISO/TR 20174:2005(E)
Table 1 (continued)
Group Reference standard Designation
JIS G 3106 SM490YATMC
SM490YBTMC
SM520BTMC
SM520CTMC
SM570TMC
JIS G 3114 SMA490AWTMC
SMA490APTMC
SMA490BWTMC
2.1
SMA490BPTMC
SMA490CWTMC
SMA490CPTMC
JIS G 3114 SMA570WTMC
SMA570PTMC
JIS G 3115 SPV410TMC
SPV450TMC
JIS G 3129 SH590P-TMC
SH590S-TMC
2.2 JIS G3115 SPV490TMC
JIS G 3106 SM570Q
JIS G 3114 SMA570WQ
SMA570PW
JIS G 3115 SPV410Q
SPV450Q
SPV490Q
JIS G 3120 SQV1B
3.1 SQV2B
SQV3A
SQV3B
JIS G 3128 SHY685
SHY685N
SHY685NS
SHY685NS-F
JIS G 3201 SF640B
6 © ISO 2005 – All rights reserved

---------------------- Page: 10 ----------------------
ISO/TR 20174:2005(E)
Table 1 (continued)
Group Reference standard Designation
JIS G 3204 SFVQ1B
3.1
SFVQ2B
SFVQ3
JIS G 3458 STPA20
4.2 JIS G 3462 STBA20
JIS G 3203 SFVAF2
JIS G 3458 STPA22
STPA23
JIS G 3462 STBA22
STBA23
JIS G 3467 STFA22
STFA23
JIS G 4109 SCMV11
5.1
SCMV12
SCMV21
SCMV22
SCMV31
SCMV32
JIS G 3203 SFVAF12
SFVAF11A
SFVAF11B
JIS G 3458 STPA24
JIS G 3462 STBA24
JIS G 3467 STFA24
JIS G 4109 SCMV41
SCMV42
SCMV51
5.2 SCMV52
JIS G 4110 SCMQ4E
JIS G 3203 SFVAF22A
SFVAF22B
SFVAF21A
SFVAF21B
JIS G 3206 SFVCMF22B
© ISO 2005 – All rights reserved 7

---------------------- Page: 11 ----------------------
ISO/TR 20174:2005(E)
Table 1 (continued)
Group Reference standard Designation
JIS G 3458 STPA25
JIS G 3462 STBA25
JIS G 3467 STFA25
JIS G 4109 SCMV61
5.3 SCMV62
JIS G 3203 S
...