ISO 6519:2015

Diesel engines — Fuel injection pumps — Tapers for shaft ends and hubs

ISO 6519:2015 specifies the dimensions of tapered shaft ends and hubs of fuel injection pumps and common-rail high pressure pumps for diesel (compression-ignition) engines. The specified shaft ends and hubs may be used with or without Woodruff keys. NOTE The specified shaft ends and hubs can also be used for other applications where no specific standards exist.

Moteurs diesels — Pompes d'injection de combustible — Cônes pour bouts d'arbre et moyeux

General Information

• Status: Withdrawn
• Publication Date: 22-Jul-2015
• ICS: 43.060.40 - Fuel systems
• Technical Committee: ISO/TC 22/SC 34 - Propulsion, powertrain and powertrain fluids
• Drafting Committee: ISO/TC 22/SC 34 - Propulsion, powertrain and powertrain fluids
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 23-Jun-2023

Relations

• Revises: ISO 6519:2004 - Diesel engines — Fuel injection pumps — Tapers for shaft ends and hubs
• Effective Date: 08-Jun-2013
• Consolidated By: ISO 7668:2018 - Anodizing of aluminium and its alloys — Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 degrees, 45 degrees, 60 degrees or 85 degrees
• Effective Date: 06-Jun-2022
• Revised: ISO 6519:2023 - Diesel engines — Fuel injection pumps — Tapers for shaft ends and hubs
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6519
Fourth edition
2015-08-15
Diesel engines — Fuel injection pumps
— Tapers for shaft ends and hubs
Moteurs diesels — Pompes d’injection de combustible — Cônes pour
bouts d’arbre et moyeux
Reference number
ISO 6519:2015(E)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 6519:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6519:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Dimensions and tolerances . 1
2.1 General . 1
2.2 Shaft ends with taper . 1
2.3 Keyways of hub with taper . 1
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6519:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on th
...