Agricultural tractors — Front-mounted equipment — Part 1: Power take-off: Safety requirements and clearance zone around PTO

This document specifies safety requirements for, and clearance zones around, front-mounted power take-offs (PTO) on agricultural tractors. NOTE 1 Further specifications for front-mounted power take-offs are given in ISO 8759-3. It is not applicable to tractors which are designed to run in two directions, where either end can be considered to be the front or the rear. NOTE 2 In this case, ISO 500 (all parts) apply.

Tracteurs agricoles — Équipement monté à l'avant — Partie 1: Prise de force: Exigences de sécurité et zone de dégagement autour de la prise de force

Le présent document spécifie des exigences de sécurité relatives aux prises de force montées à l'avant des tracteurs agricoles, ainsi que des zones de dégagement autour de ces prises de force. NOTE 1 De plus amples spécifications concernant les prises de force montées à l'avant sont données dans l'ISO 8759‑3. Il n'est pas applicable aux tracteurs conçus pour se déplacer dans deux directions et dont chacune des deux extrémités peut être indifféremment considérée comme l'extrémité avant ou l'extrémité arrière. NOTE 2 Dans ce cas, l'ISO 500 (toutes les parties) s'appliquent.

Kmetijski traktorji - Spredaj nameščena oprema - 1. del: Priključna gred: varnostne zahteve in območje nihanja okoli PTO

General Information

Status
Published
Publication Date
14-Nov-2018
Current Stage
9060 - Close of review
Start Date
04-Jun-2029

Relations

Buy Standard

Standard
ISO 8759-1:2018 - Agricultural tractors -- Front-mounted equipment
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 8759-1:2020
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 8759-1:2018 - Tracteurs agricoles -- Équipement monté a l'avant
French language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 8759-1
Third edition
2018-11
Agricultural tractors — Front-
mounted equipment —
Part 1:
Power take-off: Safety requirements
and clearance zone around PTO
Tracteurs agricoles — Équipement monté à l'avant —
Partie 1: Prise de force: Exigences de sécurité et zone de dégagement
autour de la prise de force
Reference number
ISO 8759-1:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 8759-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 8759-1:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative reference(s) . 1
3 Terms and definitions . 1
4 Safety requirements . 1
5 Clearance zone around PTO . 2
Bibliography . 5
© ISO 2018 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 8759-1:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture
and forestry, Subcommittee SC 4, Tractors.
Any feedback or questions on this document should be direct
...

SLOVENSKI STANDARD
SIST ISO 8759-1:2020
01-november-2020
Kmetijski traktorji - Spredaj nameščena oprema - 1. del: Priključna gred: varnostne
zahteve in območje nihanja okoli PTO
Agricultural tractors - Front-mounted equipment - Part 1: Power take-off: Safety
requirements and clearance zone around PTO
Tracteurs agricoles - Équipement monté à l'avant
Ta slovenski standard je istoveten z: ISO 8759-1:2018
ICS:
65.060.10 Kmetijski traktorji in prikolice Agricultural tractors and
trailed vehicles
SIST ISO 8759-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 8759-1:2020

---------------------- Page: 2 ----------------------
SIST ISO 8759-1:2020
INTERNATIONAL ISO
STANDARD 8759-1
Third edition
2018-11
Agricultural tractors — Front-
mounted equipment —
Part 1:
Power take-off: Safety requirements
and clearance zone around PTO
Tracteurs agricoles — Équipement monté à l'avant —
Partie 1: Prise de force: Exigences de sécurité et zone de dégagement
autour de la prise de force
Reference number
ISO 8759-1:2018(E)
©
ISO 2018

---------------------- Page: 3 ----------------------
SIST ISO 8759-1:2020
ISO 8759-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 8759-1:2020
ISO 8759-1:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative reference(s) . 1
3 Terms and definitions . 1
4 Safety requirements . 1
5 Clearance zone around PTO . 2
Bibliography . 5
© ISO 2018 – All rights reserved iii

---------------------- Page: 5 ----------------------
SIST ISO 8759-1:2020
ISO 8759-1:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all suc
...

NORME ISO
INTERNATIONALE 8759-1
Troisième édition
2018-11
Tracteurs agricoles — Équipement
monté à l'avant —
Partie 1:
Prise de force: Exigences de sécurité et
zone de dégagement autour de la prise
de force
Agricultural tractors — Front-mounted equipment —
Part 1: Power take-off: Safety requirements and clearance zone
around PTO
Numéro de référence
ISO 8759-1:2018(F)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 8759-1:2018(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2018
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2018 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 8759-1:2018(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et definitions . 1
4 Exigences de sécurité . 1
5 Zone de dégagement autour de la prise de force . 2
Bibliographie . 5
© ISO 2018 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 8759-1:2018(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/directives).
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'I
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.