Marine structures — Crude oil offloading systems — Hose reels

This document specifies requirements for the design, operation and acceptance tests of hose reels for crude oil offloading systems. It is applicable to the design, manufacture and acceptance of hose reels for crude oil offloading systems used on marine structures such as floating production storage & offloading (FPSO) and mobile platforms.

Structures maritimes — Systèmes de déchargement de pétrole brut — Dévidoirs

General Information

Status
Published
Publication Date
22-Oct-2020
Current Stage
6060 - International Standard published
Start Date
23-Oct-2020
Completion Date
23-Oct-2020
Ref Project

Buy Standard

Standard
ISO 24043:2020 - Marine structures -- Crude oil offloading systems -- Hose reels
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/PRF 24043:Version 25-apr-2020 - Marine structures -- Crude oil offloading systems -- Hose reels
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 24043
First edition
2020-10
Marine structures — Crude oil
offloading systems — Hose reels
Structures maritimes — Systèmes de déchargement de pétrole brut —
Dévidoirs
Reference number
ISO 24043:2020(E)
ISO 2020
---------------------- Page: 1 ----------------------
ISO 24043:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 24043:2020(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Types ................................................................................................................................................................................................................................. 2

4.1 Basic functions ........................................................................................................................................................................................ 2

4.2 Material stress ......................................................................................................................................................................................... 2

4.3 Design and structure .......................................................................................................................................................................... 2

4.3.1 General requirement .................................................................................................................................................... 2

4.3.2 Drum design......................................................................................................................................................................... 2

4.3.3 Through-flow unit ...................................................................... ..................................................................................... 3

4.3.4 Frame design ....................................................................................................................................................................... 3

4.3.5 Drive unit ................................................................................................................................................................................ 3

4.3.6 Brake device ......................................................................................................................................................................... 3

4.3.7 Emergency release equipment ............................................................................................................................ 4

4.3.8 Operating device .............................................................................................................................................................. 4

4.3.9 Auxiliary equipment ..................................................................................................................................................... 4

5 Acceptance tests .................................................................................................................................................................................................... 4

5.1 General requirement .......................................................................................................................................................................... 4

5.2 No-load test ................................................................................................................................................................................................ 4

5.3 Load test ....................................................................................................................................................................................................... 5

5.4 Braking test ................................................................................................................................................................................................ 5

5.5 Pressure test .............................................................................................................................................................................................. 5

6 Designation system ............................................................................................................................................................................................ 5

6.1 Designation of product models ................................................................................................................................................. 5

6.2 Nameplate ................................................................................................................................................................................................... 6

© ISO 2020 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 24043:2020(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/

iso/ foreword .html.

This document was prepared by Technical Committee ISO/TC 8, Ships and marine technology,

Subcommittee SC 4, Outfitting and deck machinery.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 24043:2020(E)
Marine structures — Crude oil offloading systems —
Hose reels
1 Scope

This document specifies requirements for the design, operation and acceptance tests of hose reels for

crude oil offloading systems.

It is applicable to the design, manufacture and acceptance of hose reels for crude oil offloading systems

used on marine structures such as floating production storage & offloading (FPSO) and mobile

platforms.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 3828, Shipbuilding and marine structures — Deck machinery — Vocabulary and symbols

3 Terms and definitions
For the purposes of this document, the terms and definitions
...

DRAFT INTERNATIONAL STANDARD
ISO/DIS 24043
ISO/TC 8/SC 4 Secretariat: SAC
Voting begins on: Voting terminates on:
2020-03-16 2020-06-08
Marine structures — Crude oil offloading system — Hose
reels
ICS: ISO ics
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
This document is circulated as received from the committee secretariat.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 24043:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020
---------------------- Page: 1 ----------------------
ISO/DIS 24043:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DIS 24043:2020(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Types ................................................................................................................................................................................................................................. 2

4.1 Basic functions ........................................................................................................................................................................................ 2

4.2 Strength ......................................................................................................................................................................................................... 2

4.3 Design and structure .......................................................................................................................................................................... 2

4.3.1 General requirement .................................................................................................................................................... 2

4.3.2 Drum design......................................................................................................................................................................... 2

4.3.3 Through-flow unit ...................................................................... ..................................................................................... 3

4.3.4 Frame design ....................................................................................................................................................................... 3

4.3.5 Drive unit ................................................................................................................................................................................ 3

4.3.6 Brake device ......................................................................................................................................................................... 3

4.3.7 Emergency release equipment ............................................................................................................................ 4

4.3.8 Operating device .............................................................................................................................................................. 4

4.3.9 Auxiliary equipment ..................................................................................................................................................... 4

5 Acceptance tests .................................................................................................................................................................................................... 4

5.1 General requirement .......................................................................................................................................................................... 4

5.2 No-load test ................................................................................................................................................................................................ 4

5.3 Load test ....................................................................................................................................................................................................... 5

5.4 Braking test ................................................................................................................................................................................................ 5

5.5 Pressure test .............................................................................................................................................................................................. 5

6 Designation system ............................................................................................................................................................................................ 6

6.1 Designation of product models ................................................................................................................................................. 6

6.2 Nameplate ................................................................................................................................................................................................... 6

© ISO 2020 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/DIS 24043:2020(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www .iso .org/ iso/ foreword .html.

This document was prepared by Technical Committee 8, Ships and marine technology, Subcommittee 4,

Outfitting and deck machinery.
iv © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 24043:2020(E)
Marine structures — Crude oil offloading system — Hose
reels
1 Scope

This document specifies the design, operation and acceptance test of hose reels for the crude oil

offloading system.

This document is applicable to the design, manufacture and acceptance of hose reels for the crude oil

offloading system used on marine structures such as FPSO and mobile platform.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

const
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.