Reduction sleeves and extension sockets for tools with Morse taper shanks

ISO 238:2016 specifies the dimensions of the following two pieces of equipment: a) reduction sleeves for tools with Morse taper shanks; b) extension sockets for tools with Morse taper shanks. It comprises, for each of them, two tables giving the dimensions in millimetres and the corresponding dimensions in inches, respectively.

Douilles de réduction et allonges pour outils au cône Morse

General Information

Status
Published
Publication Date
13-Nov-2016
Current Stage
9093 - International Standard confirmed
Completion Date
31-Oct-2022
Ref Project

Relations

Buy Standard

Standard
ISO 238:2016 - Reduction sleeves and extension sockets for tools with Morse taper shanks
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 238:2016 - Douilles de réduction et allonges pour outils au cône Morse
French language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 238
Second edition
2016-11-15
Reduction sleeves and extension
sockets for tools with Morse taper
shanks
Douilles de réduction et allonges pour outils au cône Morse
Reference number
ISO 238:2016(E)
ISO 2016
---------------------- Page: 1 ----------------------
ISO 238:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 238:2016(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Interchangeability .............................................................................................................................................................................................. 1

4.1 General ........................................................................................................................................................................................................... 1

4.2 Reduction sleeves ................................................................................................................................................................................. 1

4.3 Extension sockets ................................................................................................................................................................................. 1

5 Reduction sleeves for tools with Morse taper shanks ................................................................................................... 2

6 Extension sockets for tools with Morse taper shanks ................................................................................................... 4

Annex A (informative) Relationship between designations in this document and ISO 13399 ................8

Bibliography ................................................................................................................................................................................................................................ 9

© ISO 2016 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 238:2016(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,

as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the

Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.

The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, Holding

tools, adaptive items and interfaces.

This second edition cancels and replaces the first edition (ISO 238:1974), of which it constitutes a minor

revision, notably with the addition of Annex A, which gives the relationship between the designations

of this document and the ISO 13399 series.
iv © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 238:2016(E)
Reduction sleeves and extension sockets for tools with
Morse taper shanks
1 Scope
This document specifies the dimensions of the following two pieces of equipment:
a) reduction sleeves for tools with Morse taper shanks;
b) extension sockets for tools with Morse taper shanks.

It comprises, for each of them, two tables giving the dimensions in millimetres and the corresponding

dimensions in inches, respectively.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
No terms and definitions are listed in this document.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
4 Interchangeability
4.1 General

The numerical values given, whether in millimetres or in inches, automatically ensure interchangeability

with the corresponding machines and tools, whatever the system of units employed.

The mating dimensions of the sleeves and sockets are in fact in accordance with those specified

in ISO 296 for Morse taper shanks, which were determined so as to give the same guarantee of

interchangeability.
4.2 Reduction sleeves

In the reduction sleeves in millimetres and in inches, the inside taper is always strictly the same as the

standard Morse taper of the same number, even in its length.

The same applies to the outside taper, except for the length which is sometimes equal to or sometimes

greater than that of the standard taper of the same number.
4.3 Extension sockets

The statements made above concerning the Morse taper dimensions of the reduction sleeves are equally

applicable to the extension sockets, under the same conditions.
© ISO 2016 – All rights reserved 1
---------------------- Page: 5 ----------------------
ISO 238:2016(E)
Table 3 and Table 4 also
...

NORME ISO
INTERNATIONALE 238
Deuxième édition
2016-11-15
Douilles de réduction et allonges pour
outils au cône Morse
Reduction sleeves and extension sockets for tools with Morse taper
shanks
Numéro de référence
ISO 238:2016(F)
ISO 2016
---------------------- Page: 1 ----------------------
ISO 238:2016(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016, Publié en Suisse

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée

sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur

l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à

l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 238:2016(F)
Sommaire Page

Avant-propos ..............................................................................................................................................................................................................................iv

1 Domaine d’application ................................................................................................................................................................................... 1

2 Références normatives ................................................................................................................................................................................... 1

3 Termes et définitions ....................................................................................................................................................................................... 1

4 Interchangeabilité ............................................................................................................................................................................................... 1

4.1 Généralités .................................................................................................................................................................................................. 1

4.2 Douilles de réduction ........................................................................................................................................................................ 1

4.3 Allonges ......................................................................................................................................................................................................... 1

5 Douilles de réduction pour outils à queue cône Morse................................................................................................ 2

6 Allonges pour outils à queue cône Morse ................................................................................................................................... 3

Annexe A (informative) Relation entre les désignations dans la présente Norme

internationale et l’ISO 13399 .................................................................................................................................................................. 7

Bibliographie .............................................................................................................................................................................................................................. 8

© ISO 2016 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 238:2016(F)
Avant-propos

L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes

nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est

en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.

L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui

concerne la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents

critères d’approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.

iso.org/directives).

L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de

droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant

les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de

l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de

brevets reçues par l’ISO (voir www.iso.org/brevets).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un

engagement.

Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à l’évaluation

de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes de l’Organisation

mondiale du commerce (OMC) concernant les obstacles techniques au commerce (OTC), voir le lien

suivant: www.iso.org/iso/fr/avant-propos.html

Le comité chargé de l’élaboration du présent document est l’ISO/TC 29, Petit outillage, sous-comité SC 2,

Porte-outils, éléments relatifs aux attachements et interfaces.

Cette deuxième édition annule et remplace la première édition (ISO 238:1974), dont elle constitue une

révision mineure avec l’ajout de l’Annexe A, qui donne la relation entre les désignations de la présente

Norme internationale et la série des ISO 13399.
iv © ISO 2016 – Tous droits réservés
---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 238:2016(F)
Douilles de réduction et allonges pour outils au cône Morse
1 Domaine d’application
Le présent document spécifie les dimensions des deux outils suivants:
a) douilles de réduction pour outils à queue cône Morse;
b) allonges pour outils à queue cône Morse.

Il comprend, pour chacun d’eux, deux tableaux donnant respectivement les dimensions en millimètres

et les dimensions correspondantes en inches.
2 Références normatives
Il n’y a pas de références normatives dans le présent document.
3 Termes et définitions
Aucun terme, aucune définition n’est listé(e) dans le présent document.

L’ISO et l’IEC maintiennent des bases de données terminologiques destinées à être utilisées dans le

cadre de la normalisation, aux adresses suivantes:
— IEC Electropedia: disponible sur http://www.electropedia.org/

— ISO Plateforme de consultation en ligne: disponible sur https://www.iso.org/obp

4 Interchangeabilité
4.1 Généralités

Les valeurs numériques, qu’elles soient en millimètres ou en inches, assurent automatiquement

l’interchangeabilité avec les machines et les outils correspondants, quel que soit le système d’unités

employé.

Les dimensions de raccordement des douilles et des allonges concordent en effet avec celles de l’ISO 296

pour les emmanchements à queues cône Morse, dimensions qui ont été déterminées de façon à donner

cette même garantie d’interchangeabilité.
4.2 Douilles de réduction

Dans les douilles de réduction en millimètres et en inches, le cône intérieur est toujours strictement

identique au cône Morse normalisé de même numéro, même en ce qui concerne la longueur.

Il en est de même pour le cône extéri
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.