ISO 8483:2003/Amd 1:2012

Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints — Amendment 1

Tubes et raccords en plastiques thermodurcissables renforcés de verre (PRV) — Méthode d'essai pour confirmer la conception des assemblages à brides boulonnées — Amendement 1

General Information

• Status: Withdrawn
• Publication Date: 23-Jan-2012
• Withdrawal Date: 23-Jan-2012
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: ISO/TC 138/SC 6 - Reinforced plastics pipes and fittings for all applications
• Drafting Committee: ISO/TC 138/SC 6/WG 3 - Specifications for pipe systems
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 02-Aug-2019

Relations

• Revised: ISO 8483:2019 - Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints
• Effective Date: 18-Oct-2014
• Amends: ISO 8483:2003 - Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints
• Effective Date: 28-Aug-2021

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 8483
First edition
2003-12-01
AMENDMENT 1
2012-02-01
Glass-reinforced thermosetting plastics
(GRP) pipes and fittings — Test methods
to prove the design of bolted flange joints
AMENDMENT 1
Tubes et raccords en plastiques thermodurcissables renforcés de
verre (PRV) — Méthodes d’essai pour confirmer la conception des
assemblages à brides boulonnées
AMENDEMENT 1
Reference number
ISO 8483:2003/Amd.1:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 8483:2003/Amd.1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 8483:2003/Amd.1:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 8483:2003 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and
valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all applications.
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 8483:2003/Amd.1:2012(E)
Glass-reinforced thermosetting plastics (GRP) pipes and
fittings — Test methods to prove the design of bolted flange joints
AMENDMENT
...