Hexagon high nuts (style 2) — Product grades A and B

ISO 4033:2012 specifies the characteristics of hexagon high nuts (style 2), with threads from M5 up to and including M36, with product grade A for threads of diameter less than or equal to M16 and product grade B for threads of diameter greater than M16.

Écrous hexagonaux hauts (style 2) — Grades A et B

L'ISO 4033:2012 spécifie les caractéristiques des écrous hexagonaux hauts (style 2), de diamètres de filetage M5 à M36 inclus, de grade A pour les filetages de diamètre inférieur ou égal à M16 et de grade B pour les filetages de diamètre supérieur à M16.

General Information

Status
Withdrawn
Publication Date
12-Dec-2012
Current Stage
9599 - Withdrawal of International Standard
Completion Date
31-Aug-2023
Ref Project

Relations

Buy Standard

Standard
ISO 4033:2012 - Hexagon high nuts (style 2) -- Product grades A and B
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 4033:2012 - Écrous hexagonaux hauts (style 2) -- Grades A et B
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 4033
Third edition
2012-12-15
Hexagon high nuts (style 2) — Product
grades A and B
Écrous hexagonaux hauts (style 2) — Grades A et B
Reference number
ISO 4033:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 4033:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 4033:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Dimensions . 1
4 Requirements and reference International Standards . 4
5 Designation . 4
Bibliography . 5
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 4033:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4033 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 12, Fasteners with
metric internal thread.
This third edition cancels and replaces the second edition (ISO 4033:1999), of which it constitutes a minor revision.
iv © ISO 2012 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 4033:2012(E)
Introduction
This International Standard belongs to a complete group of product standards developed by ISO on external
hexagon drive fasteners. It comprises the following:
a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042,
ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513);
d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072);
e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and ISO 21670).
© ISO 2012 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 4033:2012(E)
Hexagon high nuts (style 2) — Product grades A and B
1 Scope
This International Standard specifies the characteristics of hexagon high nuts (style 2), with threads from M5
up to and including M36, with product grade A for threads D ≤ M16 and product grade B for threads D > M16.
If, in special cases, specifications other than those listed in this International Standard are required, they can
be selected from existing International Standards, for example ISO 724, ISO 898-2, ISO 965-1 and ISO 4759-1.
NOTE For hexagon regular nuts (style 1), see ISO 4032.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable
to its application. For undated references, the latest edition of the referenced document (including any
amendments) applies.
ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions
ISO 724, ISO general-purpose metric screw threads — Basic dimensions
ISO 898-2, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with
specified property classes — Coarse thread and fine pitch thread
ISO 965-1, ISO general-purpose metric screw threads — Tolerances — Part 1: Principles and basic data
ISO 3269, Fasteners — Acceptance inspection
ISO 4042, Fasteners — Electroplated coatings
ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 6157-2, Fasteners — Surface discontinuities — Part 2: Nuts
ISO 8992, Fasteners — General require
...

NORME ISO
INTERNATIONALE 4033
Troisième édition
2012-12-15
Écrous hexagonaux hauts (style 2) —
Grades A et B
Hexagon high nuts (style 2) — Product grades A and B
Numéro de référence
ISO 4033:2012(F)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 4033:2012(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2012
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l’accord écrit
de l’ISO à l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2012 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 4033:2012(F)
Sommaire Page
Avant-propos .iv
Introduction . v
1 Domaine d’application . 1
2 Références normatives . 1
3 Dimensions . 1
4 Exigences et Normes internationales de référence . 3
5 Désignation . 4
Bibliographie . 5
© ISO 2012 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 4033:2012(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux de
normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général confiée aux
comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales,
en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 2.
La tâche principale des comités techniques est d’élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur publication
comme Normes internationales requiert l’approbation de 75 % au moins des comités membres votants.
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de droits
de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de ne pas avoir
identifié de tels droits de propriété et averti de leur existence.
L’ISO 4033 a été élaborée par le comité technique ISO/TC 2, Éléments de fixation, sous-comité SC 12, Éléments
de fixation à filetage métrique intérieur.
Cette troisième édition annule et remplace la deuxième édition (ISO 4033:1999), qui a fait l’objet d’une
révision mineure.
iv © ISO 2012 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO 4033:2012(F)
Introduction
La présente Norme internationale fait partie d’une série complète des normes de produit développées par l’ISO
traitant des éléments de fixation à entraînement hexagonal. La série comprend:
a) les vis à tête hexagonale partiellement filetées (ISO 4014, ISO 4015, ISO 4016 et ISO 8765);
b) les vis à tête hexagonale entièrement filetées (ISO 4017, ISO 4018 et ISO 8676);
c) les écrous hexagonaux (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041,
ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 et ISO 10513);
d) les vis à tête hexagonale à embase (ISO 4162, ISO 15071 et ISO 15072);
e) les écrous hexagonaux à embase (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126
et ISO 21670);
© ISO 2012 – Tous droits réservés v

---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 4033:2012(F)
Écrous hexagonaux hauts (style 2) — Grades A et B
1 Domaine d’application
La présente Norme internationale spécifie les caractéristiques des écrous hexagonaux hauts (style 2), de diamètres
de filetage M5 à M36 inclus, de grade A pour les filetages D ≤ M16 et de grade B pour les filetages D > M16.
Si, dans des cas particuliers, des spécifications autres que celles figurant dans la présente Norme internationale
sont requises, elles peuvent être choisies dans les Normes internationales existantes, par exemple ISO 724,
ISO 898-2, ISO 965-1 et ISO 4759-1.
NOTE Pour les écrous hexagonaux normaux de style 1, voir l’ISO 4032.
2 Références normatives
Les documents suivants, en totalité ou en partie, sont référencés de manière normative dans le présent
document et sont indispensables pour son application. Pour les références datées, seule l’édition citée
s’applique. Pour les références non datées, la dernière édition du document de référence s’applique (y compris
les éventuels amendements).
ISO 225, Éléments de fixation — Vis, goujons et écrous — Symboles et description des dimensions
ISO 724, Filetages métriques ISO pour usages généraux — Dimensions de base
ISO 898-2, Caractéristiques mécaniques des éléments de fixation en acier au carbone et en acier allié —
Partie 2: Écrous de classes de qualité spécifiées — Filetages à pas gros et filetages à pas fin
ISO 965-1, Filetages métriques ISO pour usages généraux — Tolérances — Partie 1: Principes et données
fondamentales
ISO 3269, Éléments de fixation — Contrôle de réception
ISO 4042, Éléments de fixation — Revêtements électrolytiques
ISO 4759-1, Tolérances des éléments de fixation — Partie 1: Vis, goujons et écrous — Grades A, B et
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.