Carbonaceous materials used in the production of aluminium — Prebaked anodes and cathode blocks — Part 2: Determination of flexural strength by the four-point method

ISO 12986-2:2014 specifies a four-point method to determine the flexural strength of carbon and solid graphite materials at room temperature.

Produits carbonés utilisés pour la production de l'aluminium — Anodes précuites et blocs cathodiques — Partie 2: Détermination de la résistance à la flexion par la méthode quatre points

General Information

Status
Published
Publication Date
30-Jun-2014
Current Stage
9093 - International Standard confirmed
Completion Date
31-Jan-2020
Ref Project

Relations

Buy Standard

Standard
ISO 12986-2:2014 - Carbonaceous materials used in the production of aluminium -- Prebaked anodes and cathode blocks
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 12986-2
Third edition
2014-06-15
Carbonaceous materials used in the
production of aluminium — Prebaked
anodes and cathode blocks —
Part 2:
Determination of flexural strength by
the four-point method
Produits carbonés utilisés pour la production de l’aluminium —
Anodes précuites et blocs cathodiques —
Partie 2: Détermination de la résistance à la flexion par la méthode
quatre points
Reference number
ISO 12986-2:2014(E)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO 12986-2:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 12986-2:2014(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Test specimen . 3
6.1 Sampling and sample preparation . 3
6.2 Size and geometry . 4
7 Procedure. 4
8 Calculation and expression of results . 4
8.1 Bending moment, M .
b 4
8.2 Flexural strength, σ .
b 5
9 Precision . 6
10 Test report . 6
Bibliography . 7
© ISO 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 12986-2:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 226, Materials for production of primary
aluminium.
This third edition cancels and replaces the second edition (ISO 12986-2:2009), which has been technically
revised.
ISO 12986 consists of the following parts, under the general title Carbonaceous materials used in the
production of aluminium — Prebaked anodes and cathode blocks:
— Part 1: Determination of bending strength by the three-point method
— Part 2: Determination of flexural strength by the four-point method
iv © ISO 2014 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 12986-2:2014(E)
Carbonaceous materials used in the production of
aluminium — Prebaked anodes and cathode blocks —
Part 2:
Determination of flexural strength by the four-point
method
1 Scope
This part of ISO 12986 specifies a four-point method to determine the flexural strength of carbon and
solid graphite materials at room temperature.
NOTE This part of ISO 12986 is based on DIN 51944.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 4288, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Rules and
procedures for the assessment of surface texture
ISO 7500-1, Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression
testing machines — Verification and calibration of the force-measuring system
ISO 8007-1, Carbonaceous materials used in the production of aluminium — Sampling plans and sampling
from individual units — Part 1: Cathode blocks
ISO 8007-2, Carbonaceous materials used in the production of aluminium — Sampling plans and sampling
from individual units — Part 2: Prebaked anodes
ISO 8007-3, Carbonaceous materials used in the production of aluminium — Sampling plans and sampling
from individual units — Part 3: Sidewall blocks
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.