Machine tools — Dimensions and geometric tests for self-centring chucks with two-piece jaws — Part 2: Power-operated chucks with tongue and groove type jaws

ISO 3442-2:2005 specifies the sizes for interchangeability of self-centring, power-operated chucks with two-piece jaws (tongue and groove type) and describes, by reference to ISO 230-1, the geometric tests for such chucks. It also specifies the tolerances which apply to these tests.

Machines-outils — Dimensions et essais géométriques pour mandrins à serrage concentrique et à mors rapportés — Partie 2: Mandrins à commande axiale assistée avec mors à assemblage cruciforme par tenon et languette

L'ISO 3442-2:2005 spécifie les dimensions d'interchangeabilité et, par référence à l'ISO 230-1, les essais géométriques pour les mandrins à commande axiale assistée, à serrage concentrique et à mors rapportés (assemblage cruciforme par tenon et languette). Elle spécifie également les tolérances applicables à ces essais.

General Information

Status
Published
Publication Date
26-Oct-2005
Current Stage
9093 - International Standard confirmed
Completion Date
08-Oct-2019
Ref Project

Relations

Buy Standard

Standard
ISO 3442-2:2005 - Machine tools -- Dimensions and geometric tests for self-centring chucks with two-piece jaws
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 3442-2:2005 - Machines-outils -- Dimensions et essais géométriques pour mandrins a serrage concentrique et a mors rapportés
French language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3442-2
First edition
2005-10-15

Machine tools — Dimensions and
geometric tests for self-centring chucks
with two-piece jaws —
Part 2:
Power-operated chucks with tongue and
groove type jaws
Machines-outils — Dimensions et essais géométriques pour mandrins à
serrage concentrique et à mors rapportés —
Partie 2: Mandrins à commande axiale assistée avec mors à
assemblage cruciforme par tenon et languette



Reference number
ISO 3442-2:2005(E)
©
ISO 2005

---------------------- Page: 1 ----------------------
ISO 3442-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3442-2:2005(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Preliminary remarks . 1
3.1 Measurement units . 1
3.2 Geometric tests. 1
4 Accuracy classes. 1
5 Sizes for interchangeability . 2
6 Geometric tests. 3
6.1 Spindle or face plate accuracy . 3
6.2 Geometric tests and relevant tolerances for power-operated chucks. 6
Bibliography . 11

© ISO 2005 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3442-2:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3442-2 was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 8, Work
holding spindles and chucks.
Together with ISO 3442-1 and ISO 3442-3, this first edition of ISO 3442-2 cancels and replaces
ISO 3442:1991 and ISO 9401:1991. ISO/TC 39/SC 8 decided to split ISO 3442:1991 into three parts, at the
same time incorporating ISO 9401:1991. As soon as all three parts of ISO 3442 are published, ISO 3442:1991
and ISO 9401:1991 will be withdrawn.
ISO 3442 consists of the following parts, under the general title Machine tools — Dimensions and geometric
tests for self-centring chucks with two-piece jaws:
⎯ Part 1: Manually operated chucks with tongue and groove type jaws
⎯ Part 2: Power-operated chucks with tongue and groove type jaws
⎯ Part 3: Power-operated chucks with serrated jaws
iv © ISO 2005 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3442-2:2005(E)

Machine tools — Dimensions and geometric tests for self-
centring chucks with two-piece jaws —
Part 2:
Power-operated chucks with tongue and groove type jaws
1 Scope
This part of ISO 3442 specifies the sizes for interchangeability of self-centring, power-operated chucks with
two-piece jaws (tongue and groove type) and describes, by reference to ISO 230-1, the geometric tests for
such chucks. It also specifies the tolerances which apply to these tests.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 230-1:1996, Test code for machine tools — Part 1: Geometric accuracy of machines operating under
no-load or finishing conditions
3 Preliminary remarks
3.1 Measurement units
All dimensions and tolerances in this part of ISO 3442 are expressed in millimetres.
3.2 Geometric tests
This part of ISO 3442 deals only with the verification of the rotational accuracy of the chuck and the
positioning of the assembling elements of the top jaws. It does not apply to other dynamic considerations,
such as measurement of lack of balance during rotation, balancing or measurement of gripping power.
The main purpose of these tests is to allow either top jaw mounting compatible with the machining accuracy of
the chuck or precise setting for top jaws on the chuck after carrying out preliminary centring, straightening
...

NORME ISO
INTERNATIONALE 3442-2
Première édition
2005-10-15


Machines-outils — Dimensions et essais
géométriques pour mandrins à serrage
concentrique et à mors rapportés —
Partie 2:
Mandrins à commande axiale assistée
avec mors à assemblage cruciforme par
tenon et languette
Machine tools — Dimensions and geometric tests for self-centring
chucks with two-piece jaws —
Part 2: Power-operated chucks with tongue and groove type jaws



Numéro de référence
ISO 3442-2:2005(F)
©
ISO 2005

---------------------- Page: 1 ----------------------
ISO 3442-2:2005(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


©  ISO 2005
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2005 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 3442-2:2005(F)
Sommaire Page
Avant-propos. iv
1 Domaine d'application. 1
2 Références normatives . 1
3 Remarques préliminaires. 1
3.1 Unités de mesure. 1
3.2 Essais géométriques. 1
4 Classes d'exactitude . 1
5 Dimensions d'interchangeabilité. 2
6 Essais géométriques. 3
6.1 Exactitude de la broche ou du faux-plateau .3
6.2 Essais géométriques et tolérances utiles pour des mandrins à commande axiale assistée. 6
Bibliographie . 11

© ISO 2005 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 3442-2:2005(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 3442-2 a été élaborée par le comité technique ISO/TC 39, Machines-outils, sous-comité SC 8, Broches
porte-pièce et mandrins.
Cette première édition de l'ISO 3442-2, avec l'ISO 3442-1 et l'ISO 3442-3, annule et remplace
l'ISO 3442:1991 et l'ISO 9401:1991. L'ISO/TC 39/SC 8 a décidé de diviser l'ISO 3442:1991 en trois parties et
de les rassembler avec l'ISO 9401:1991. Dès la publication des trois parties de l'ISO 3442, l'ISO 3442:1991 et
l'ISO 9401:1991 seront annulées.
L'ISO 3442 comprend les parties suivantes, présentées sous le titre général Machines-outils — Dimensions et
essais géométriques pour mandrins à serrage concentrique et à mors rapportés:
⎯ Partie 1: Mandrins à commande manuelle avec mors à assemblage cruciforme par tenon et languette
⎯ Partie 2: Mandrins à commande axiale assistée avec mors à assemblage cruciforme par tenon et
languette
⎯ Partie 3: Mandrins à commande axiale assistée avec mors à assemblage par dentelure
iv © ISO 2005 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 3442-2:2005(F)

Machines-outils — Dimensions et essais géométriques pour
mandrins à serrage concentrique et à mors rapportés —
Partie 2:
Mandrins à commande axiale assistée avec mors à assemblage
cruciforme par tenon et languette
1 Domaine d'application
La présente partie de l'ISO 3442 spécifie les dimensions d'interchangeabilité et, par référence à l'ISO 230-1,
les essais géométriques pour les mandrins à commande axiale assistée, à serrage concentrique et à mors
rapportés (assemblage cruciforme par tenon et languette). Elle spécifie également les tolérances applicables
à ces essais.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 230-1:1996, Code d'essai des machines-outils — Partie 1: Précision géométrique des machines
fonctionnant à vide ou dans des conditions de finition
3 Remarques préliminaires
3.1 Unités de mesure
Toutes les dimensions et tolérances spécifiées dans la présente partie de l'ISO 3442 sont exprimées en
millimètres.
3.2 Essais géométriques
La présente partie de l'ISO 3442 traite uniquement du contrôle de l'exactitude de rotation du mandrin, ainsi
que du positionnement des éléments d'assemblage des mors rapportés. Elle ne s'applique pas aux autres
considérations d'ordre dynamique, tels que le mesurage des balourds en rotation, l'équilibrage ou le
mesurage des efforts de serrage.
L'objet principal de ces essais est de permettre soit un montage des mors rapportés compatible avec
l'exactitude d'exécution du mandrin, soit un positionnement rigou
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.