ISO/TS 18234-1:2013

Intelligent transport systems — Traffic and travel information via transport protocol experts group, generation 1 (TPEG1) binary data format — Part 1: Introduction, numbering and versions (TPEG1-INV)

ISO/TS 18234-1:2013 provides an introduction and index to the complete set of TPEG Generation 1 toolkit components and applications. It allows the indexing of new applications as they are added to the TPEG applications family, by defining their Application Identification (AID).

Systèmes intelligents de transport — Informations sur le trafic et le tourisme via les données de format binaire du groupe d'experts du protocole de transport, génération 1 (TPEG1) — Partie 1: Introduction, numérotage et versions (TPEG1-INV)

General Information

• Status: Published
• Publication Date: 09-Oct-2013
• ICS: 03.220.01 - Transport in general
• ICS: 35.240.60 - IT applications in transport
• Technical Committee: ISO/TC 204 - Intelligent transport systems
• Drafting Committee: ISO/TC 204/WG 10 - Traveller information systems
• Current Stage: 9020 - International Standard under periodical review
• Start Date: 15-Apr-2024
• Completion Date: 15-Apr-2024

Relations

• Consolidates: ISO/ASTM 51631:2003 - Practice for use of calorimetric dosimetry systems for electron beam dose measurements and dosimeter calibrations
• Effective Date: 06-Jun-2022
• Revises: ISO/TS 18234-1:2006 - Traffic and Travel Information (TTI) — TTI via Transport Protocol Expert Group (TPEG) data-streams — Part 1: Introduction, numbering and versions
• Effective Date: 16-Oct-2010

Standards Content (Sample)

TECHNICAL ISO/TS
SPECIFICATION 18234-1
Second edition
2013-10-15
Intelligent transport systems — Traffic
and travel information via transport
protocol experts group, generation 1
(TPEG1) binary data format —
Part 1:
Introduction, numbering and
versions (TPEG1-INV)
Systèmes intelligents de transport — Informations sur le trafic et le
tourisme via les données de format binaire du groupe d’experts du
protocole de transport, génération 1 (TPEG1) —
Partie 1: Introduction, numérotage et versions (TPEG1-INV)
Reference number
ISO/TS 18234-1:2013(E)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO/TS 18234-1:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TS 18234-1:2013(E)

Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Abbreviated terms . 2
4 Application identification . 2
Annex A (normative) Overview of parts, naming and versions . 4
Annex B (informative) Applications and bearers . 5
Bibliography . 6
© ISO 2013 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/TS 18234-1:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of normative document:
— an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical
experts in an ISO working group and is accepted for publication if it is approved by more than 50 % of
the members of the parent committee casting a vote;
— an ISO Technical Specification (ISO/TS) represents an agreement between the m
...