Road vehicles — Compressed natural gas (CNG) fuel system components — Part 13: Pressure relief device (PRD) — Amendment 1

Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 13: Dispositifs de limitation de pression — Amendement 1

General Information

Status
Published
Publication Date
22-Mar-2016
Current Stage
6060 - International Standard published
Start Date
23-Mar-2016
Completion Date
23-Mar-2016
Ref Project

RELATIONS

Buy Standard

Standard
ISO 15500-13:2012/Amd 1:2016
English language
1 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 15500-13:2012/Amd 1:2016
English language
1 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 15500-13
Second edition
2012-04-15
AMENDMENT 1
2016-04-01
Road vehicles — Compressed natural
gas (CNG) fuel system components —
Part 13:
Pressure relief device (PRD)
AMENDMENT 1
Véhicules routiers — Composants des systèmes de combustible gaz
naturel comprimé (GNC) —
Partie 13: Dispositifs de limitation de pression
AMENDEMENT 1
Reference number
ISO 15500-13:2012/Amd.1:2016(E)
ISO 2016
---------------------- Page: 1 ----------------------
ISO 15500-13:2012/Amd.1:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 15500-13:2012/Amd.1:2016(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all
...

DRAFT AMENDMENT
ISO 15500-13:2012/DAM 1
ISO/TC 22/SC 41 Secretariat: UNI
Voting begins on: Voting terminates on:
2015-08-19 2015-11-19
Road vehicles — Compressed natural gas (CNG) fuel
system components —
Part 13:
Pressure relief device (PRD)
AMENDMENT 1

Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) —

Partie 13: Dispositifs de limitation de pression
AMENDEMENT 1
ICS: 43.060.40
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 15500-13:2012/DAM 1:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015
---------------------- Page: 1 ----------------------
ISO 15500-13:2012/DAM 1:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s me

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.