Soil quality — Gas chromatographic determination of the content of volatile aromatic hydrocarbons, naphthalene and volatile halogenated hydrocarbons — Purge-and-trap method with thermal desorption

ISO 15009:2016 specifies a method for quantitative gas-chromatographic determination of volatile aromatic hydrocarbons, naphthalene and volatile halogenated hydrocarbons in soil. This International Standard is applicable to all types of soil. NOTE In the case of unsaturated peaty soils, absorption of the extraction solution may occur. The lower limit of quantification is dependent on the equipment used and the quality of the methanol grade used for the extraction of the soil sample. Under the conditions specified in this International Standard the following limits of quantification apply (expressed on basis of dry matter): Typical limit of quantification when using GC-FID: - Volatile aromatic hydrocarbons: 0,1 mg/kg Typical limit of quantification when using GC-ECD: - Volatile halogenated hydrocarbons: 0,01 mg/kg Lower limits of quantification for some compounds can be achieved by using mass spectrometry (MS) with selected ion detection.

Qualité du sol — Détermination par chromatographie en phase gazeuse des teneurs en hydrocarbures aromatiques volatils, en naphtalène et en hydrocarbures halogénés volatils — Méthode par purge et piégeage avec désorption thermique

ISO 15009:2016 spécifie une méthode pour la détermination quantitative par chromatographie en phase gazeuse des hydrocarbures aromatiques volatils, du naphtalène et des hydrocarbures halogénés volatils contenus dans les sols. La présente Norme internationale est applicable à tous les types de sols. NOTE En cas de sols tourbeux insaturés, une absorption de la solution d'extraction peut avoir lieu. La limite inférieure de détermination quantitative dépend du matériel utilisé et de la qualité du méthanol utilisé pour l'extraction de l'échantillon de sol. Dans les conditions spécifiées dans la présente Norme internationale, les limites de détermination quantitative suivantes (exprimées par rapport à la matière sèche) s'appliquent: Limite de détermination quantitative type lorsque le couplage CG-FID est utilisé: - Hydrocarbures aromatiques volatils: 0,1 mg/kg Limite de détermination quantitative type lorsque le couplage CG-ECD est utilisé: - Hydrocarbures halogénés volatils: 0,01 mg/kg Des limites de détermination quantitative plus faibles peuvent être atteintes pour certains composés si l'on utilise la spectrométrie de masse (SM) avec détection sélective des ions.

General Information

Status
Published
Publication Date
11-Feb-2016
Current Stage
9093 - International Standard confirmed
Start Date
22-Oct-2021
Completion Date
22-Oct-2021
Ref Project

Relations

Buy Standard

Standard
ISO 15009:2016 - Soil quality -- Gas chromatographic determination of the content of volatile aromatic hydrocarbons, naphthalene and volatile halogenated hydrocarbons -- Purge-and-trap method with thermal desorption
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 15009:2016 - Soil quality -- Gas chromatographic determination of the content of volatile aromatic hydrocarbons, naphthalene and volatile halogenated hydrocarbons -- Purge-and-trap method with thermal desorption
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 15009:2016 - Qualité du sol -- Détermination par chromatographie en phase gazeuse des teneurs en hydrocarbures aromatiques volatils, en naphtalene et en hydrocarbures halogénés volatils -- Méthode par purge et piégeage avec désorption thermique
French language
22 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 15009:2016 - Qualité du sol -- Détermination par chromatographie en phase gazeuse des teneurs en hydrocarbures aromatiques volatils, en naphtalène et en hydrocarbures halogénés volatils -- Méthode par purge et piégeage avec désorption thermique
French language
22 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 15009
ISO/TC 190/SC 3
Soil quality — Gas chromatographic
Secretariat: DIN
determination of the content of
Voting begins on:
2015­10­22 volatile aromatic hydrocarbons,
naphthalene and volatile halogenated
Voting terminates on:
2015­12­22
hydrocarbons — Purge-and-trap
method with thermal desorption
Qualité du sol — Détermination par chromatographie en phase
gazeuse des teneurs en hydrocarbures aromatiques volatils, en
naphtalène et en hydrocarbures halogénés volatils — Méthode par
purge et piégeage avec désorption thermique
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 15009:2015(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2015

ISO/FDIS 15009:2015(E)
ISO/CEN PARALLEL PROCESSING
This final draft has been developed within the International Organization for Standardization (ISO), and pro­
cessed under the ISO-lead mode of collaboration as defined in the Vienna Agreement. The final draft was
established on the basis of comments received during a parallel enquiry on the draft.
This final draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
two-month approval vote in ISO and formal vote in CEN.
Positive votes shall not be accompanied by comments.
Negative votes shall be accompanied by the relevant technical reasons.
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

ISO/FDIS 15009:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 2
4 Reagents . 2
4.1 Water, free of volatile aromatic and volatile halogenated hydrocarbons . 2
4.2 Internal standards . 2
4.3 Standard compounds . . 3
4.3.1 Volatile aromatic hydrocarbons . 3
4.3.2 Volatile halogenated hydrocarbons . 3
4.4 Methanol . 4
4.5 Adsorbing agent . 4
4.6 Cooling water for purge and trap . 4
4.7 Inert gas for the gas chromatograph . 4
4.8 Nitrogen or helium as inert gas for the purge equipment . 4
4.9 Standard solutions . 5
4.9.1 Standard stock solutions for volatile aromatic and halogenated
compounds in methanol, 4 g/l . 5
4.9.2 Internal standard solutions in methanol, 4 g/l . 5
4.9.3 Calibration solutions . 5
4.10 Methanol containing internal standards . 5
5 Apparatus . 6
6 Sampling, preservation and sample pretreatment . 7
6.1 General . 7
6.2 Sampling using vials pre-filled with methanol . 8
6.3 Sampling using coring tube method . 8
7 Procedure. 8
7.1 Blank determination . 8
7.2 Extraction . 8
7.3 Purge and trap . 9
7.4 Gas chromatographic analysis . 9
7.4.1 Gas chromatographic conditions . 9
7.4.2 Calibration .10
7.4.3 Measurement .11
8 Calculation .12
8.1 Calculation of the concentration of a volatile compound in the water sample .12
8.2 Calculation of the concentration of a volatile compound in the soil sample .12
9 Expression of results .13
10 Precision .13
11 Test report .13
Annex A (informative) Relative retention time with respect to ethylbenzene-D10 of volatile
aromatic hydrocarbons and volatile halogenated hydrocarbons on following
columns: CP-Sil 5 CB and CP-Sil 13 CB .14
Annex B (normative) Check on internal standards .16
Annex C (informative) Validation .17
Annex D (informative) Information on purge and trap instruments.20
ISO/FDIS 15009:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is Technical Committee ISO/TC 190, Soil quality,
Subcommittee SC 3, Chemical methods and soil characteristics.
This third edition cancels and replaces the second edition (ISO 15009:2012) which has been
technically revised.
iv © ISO 2015 – All rights reserved

FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 15009:2015(E)
Soil quality — Gas chromatographic determination of the
content of volatile aromatic hydrocarbons, naphthalene
and volatile halogenated hydrocarbons — Purge-and-trap
method with thermal desorption
1 Scope
This International Standard specifies a method for quantitative gas-chromatographic determination of
volatile aromatic hydrocarbons, naphthalene and volatile halogenated hydrocarbons in soil.
This International standard is applicable to all types of soil.
NOTE In the case of unsaturated peaty soils, absorption of the extraction solution may occur.
The lower limit of quantification is dependent on the equipment used and the quality of the methanol
grade used for the extraction of the soil sample.
Under the conditions specified in this International Standard the following limits of quantification
apply (expressed on basis of dry matter):
Typical limit of quantification when using GC-FID:
Volatile aromatic hydrocarbons: 0,1 mg/kg
Typical limit of quantification when using GC-ECD:
Volatile halogenated hydrocarbons: 0,01 mg/kg
Lower limits of quantification for some compounds can be achieved by using mass spectrometry (MS)
with selected ion detection.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 4799, Laboratory glassware — Condensers
ISO 10381-1, Soil quality — Sampling — Part 1: Guidance on the design of sampling programmes
ISO 10381-2, Soil quality — Sampling — Part 2: Guidance on sampling techniques
IS
...


INTERNATIONAL ISO
STANDARD 15009
Third edition
2016-02-15
Soil quality — Gas chromatographic
determination of the content of
volatile aromatic hydrocarbons,
naphthalene and volatile halogenated
hydrocarbons — Purge-and-trap
method with thermal desorption
Qualité du sol — Détermination par chromatographie en phase
gazeuse des teneurs en hydrocarbures aromatiques volatils, en
naphtalène et en hydrocarbures halogénés volatils — Méthode par
purge et piégeage avec désorption thermique
Reference number
©
ISO 2016
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 2
4 Reagents . 2
4.1 Water, free of volatile aromatic and volatile halogenated hydrocarbons . 2
4.2 Internal standards . 2
4.3 Standard compounds . . 3
4.3.1 Volatile aromatic hydrocarbons . 3
4.3.2 Volatile halogenated hydrocarbons . 3
4.4 Methanol . 4
4.5 Adsorbing agent . 4
4.6 Cooling water for purge and trap . 4
4.7 Inert gas for the gas chromatograph . 5
4.8 Nitrogen or helium as inert gas for the purge equipment . 5
4.9 Standard solutions . 5
4.9.1 Standard stock solutions for volatile aromatic and halogenated
compounds in methanol, 4 g/l . 5
4.9.2 Internal standard solutions in methanol, 4 g/l . 5
4.9.3 Calibration solutions . 5
4.10 Methanol containing internal standards . 6
5 Apparatus . 6
6 Sampling, preservation and sample pretreatment . 7
6.1 General . 7
6.2 Sampling using vials pre-filled with methanol . 8
6.3 Sampling using coring tube method . 8
7 Procedure. 8
7.1 Blank determination . 8
7.2 Extraction . 9
7.3 Purge and trap . 9
7.4 Gas chromatographic analysis . 9
7.4.1 Gas chromatographic conditions . 9
7.4.2 Calibration .10
7.4.3 Measurement .11
8 Calculation .12
8.1 Calculation of the concentration of a volatile compound in the water sample .12
8.2 Calculation of the concentration of a volatile compound in the soil sample .12
9 Expression of results .13
10 Precision .13
11 Test report .13
Annex A (informative) Relative retention time with respect to ethylbenzene-D10 of volatile
aromatic hydrocarbons and volatile halogenated hydrocarbons on following
columns: CP-Sil 5 CB and CP-Sil 13 CB .14
Annex B (normative) Check on internal standards .16
Annex C (informative) Validation .17
Annex D (informative) Information on purge and trap instruments.20
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 190, Soil quality, Subcommittee SC 3, Chemical
methods and soil characteristics.
This third edition cancels and replaces the second edition (ISO 15009:2012), which has been technically
revised.
iv © ISO 2016 – All rights reserved

INTERNATIONAL STANDARD ISO 15009:2016(E)
Soil quality — Gas chromatographic determination of the
content of volatile aromatic hydrocarbons, naphthalene
and volatile halogenated hydrocarbons — Purge-and-trap
method with thermal desorption
1 Scope
This International Standard specifies a method for quantitative gas-chromatographic determination of
volatile aromatic hydrocarbons, naphthalene and volatile halogenated hydrocarbons in soil.
This International Standard is applicable to all types of soil.
NOTE In the case of unsaturated peaty soils, absorption of the extraction solution may occur.
The lower limit of quantification is dependent on the equipment used and the quality of the methanol
grade used for the extraction of the soil sample.
Under the conditions specified in this International Standard the following limits of quantification
apply (expressed on basis of dry matter):
Typical limit of quantification when using GC-FID:
— Volatile aromatic hydrocarbons: 0,1 mg/kg
Typical limit of quantification when using GC-ECD:
— Volatile halogenated hydrocarbons: 0,01 mg/kg
Lower limits of quantification for some compounds can be achieved by using mass spectrometry (MS)
with selected ion detection.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 4799, Laboratory glassware — Condensers
ISO 10381-1, Soil quality — Sampling — Part 1: Guidance on the design of sampling programmes
ISO 10381-2, Soil quality — Sampling — Part 2: Guidance on sampling techniques
ISO 10381-5, Soil quality — Sampling — Part 5: Guidance on the procedure for the investigation of urban
and industrial sites with regard to soil contamination
ISO 11465, Soil quality — Determination of dry matter and water content on a mass basis —
Gravimetric method
ISO 15680, Water quality — Gas-chromatographic determination of a number of monocyclic aromatic
hydrocarbons, naphthalene and several chlorinated compounds using purge-and-trap and thermal
desorption
ISO 18512, Soil quality — Guidance on long and short term storage of soil samples
ISO 22892, Soil quality — Guidelines for the identification of target compounds by gas chromatography and
mass spectrometry
3 Principle
Test samples are taken from an untreated field moist soil sample. To prevent losses of the volatiles,
samples are taken as undisturbed as possible in the field with a tube corer or by adding methanol
immediately in the field.
The test sample is extracted with methanol. After centrifugation, if necessary, part of the methanol
extract is brought into a purge vessel filled with water. The volatile compounds are purged with
nitrogen or helium and adsorbed on a suitable adsorb
...


PROJET
NORME ISO/FDIS
FINAL
INTERNATIONALE 15009
ISO/TC 190/SC 3
Qualité du sol — Détermination par
Secrétariat: DIN
chromatographie en phase gazeuse
Début de vote:
2015-10-22 des teneurs en hydrocarbures
aromatiques volatils, en naphtalène et
Vote clos le:
2015-12-22
en hydrocarbures halogénés volatils
— Méthode par purge et piégeage avec
désorption thermique
Soil quality — Gas chromatographic determination of the content of
volatile aromatic hydrocarbons, naphthalene and volatile halogenated
hydrocarbons — Purge-and-trap method with thermal desorption
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSER-
Veuillez consulter les notes administratives en page iii
VATIONS, NOTIFICATION DES DROITS DE PRO-
PRIÉTÉ DONT ILS AURAIENT ÉVENTUELLEMENT
CONNAISSANCE ET À FOURNIR UNE DOCUMEN-
TATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-
Numéro de référence
MERCIALES, AINSI QUE DU POINT DE VUE
ISO/FDIS 15009:2015(F)
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
CONSIDÉRÉS DU POINT DE VUE DE LEUR POSSI-
BILITÉ DE DEVENIR DES NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTA-
©
TION NATIONALE. ISO 2015
ISO/FDIS 15009:2015(F)
TRAITEMENT PARALLÈLE ISO/CEN
Le présent projet final a été élaboré dans le cadre de l’Organisation internationale de normalisation (ISO) et
soumis selon le mode de collaboration sous la direction de l’ISO, tel que défini dans l’Accord de Vienne. Le
projet final a été établi sur la base des observations reçues lors de l’enquête parallèle sur le projet.
Le projet final est par conséquent soumis aux comités membres de l’ISO et aux comités membres du CEN en
parallèle à un vote d’approbation de deux mois au sein de l’ISO et à un vote formel au sein du CEN.
Les votes positifs ne doivent pas être accompagnés d’observations.
Les votes négatifs doivent être accompagnés des arguments techniques pertinents.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2015, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – Tous droits réservés

ISO/FDIS 15009:2015(F)
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Principe . 2
4 Réactifs . 2
4.1 Eau, exempte d’hydrocarbures aromatiques volatils et d’hydrocarbures
halogénés volatils . 2
4.2 Étalons internes . 3
4.3 Composés étalons . 3
4.3.1 Hydrocarbures aromatiques volatils . 3
4.3.2 Hydrocarbures halogénés volatils . 4
4.4 Méthanol . 4
4.5 Agent d’adsorption . 5
4.6 Eau de refroidissement, pour la purge et le piégeage . 5
4.7 Gaz inerte, pour le chromatographe en phase gazeuse . 5
4.8 Azote ou hélium, utilisé comme gaz inerte pour le dispositif de purge . 5
4.9 Solutions étalons . 5
4.9.1 Solutions étalons mères, pour composés aromatiques et halogénés
volatils dans du méthanol, 4 g/l . 5
4.9.2 Solutions étalons internes dans du méthanol, 4 g/l . 5
4.9.3 Solutions d’étalonnage . 6
4.10 Méthanol contenant des étalons internes . 6
5 Appareillage . 6
6 Échantillonnage, conservation et traitement préliminaire des échantillons .8
6.1 Généralités . 8
6.2 Échantillonnage par la méthode de flacons préremplis de méthanol . 8
6.3 Échantillonnage par la méthode du tube de carottage. 9
7 Mode opératoire. 9
7.1 Détermination à blanc . 9
7.2 Extraction . 9
7.3 Purge et piégeage .10
7.4 Analyse par chromatographie en phase gazeuse .10
7.4.1 Conditions d’analyse par chromatographie en phase gazeuse .10
7.4.2 Étalonnage .11
7.4.3 Mesurage .12
8 Calcul .12
8.1 Calcul de la concentration d’un composé volatil dans un échantillon d’eau .12
8.2 Calcul de la concentration d’un composé volatil dans l’échantillon de sol .13
9 Expression des résultats.13
10 Fidélité .14
11 Rapport d’essai .14
Annexe A (informative) Temps de rétention relatifs par rapport à l’éthylbenzène-D10 des
hydrocarbures aromatiques volatils et des hydrocarbures halogénés volatils sur les
colonnes suivantes: CP-Sil 5 CB et CP-Sil 13 CB .15
Annexe B (normative) Vérification des étalons internes .17
Annexe C (informative) Validation .18
Annexe D (informative) Informations sur les instruments de purge et de piégeage .21
ISO/FDIS 15009:2015(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO, participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer
un engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à
l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes
de l’OMC concernant les obstacles techniques au commerce (OTC), voir le lien suivant: Avant-propos -
Informations supplémentaires
Le comité chargé de l’élaboration du présent document est l’ISO/TC 190, Qualité du sol, sous-comité SC 3,
Méthodes chimiques et caractéristiques du sol.
Cette troisième édition annule et remplace la deuxième édition (ISO 15009:2012) qui a fait l’objet d’une
révision technique.
iv © ISO 2015 – Tous droits réservés

PROJET FINAL DE NORME INTERNATIONALE ISO/FDIS 15009:2015(F)
Qualité du sol — Détermination par chromatographie
en phase gazeuse des teneurs en hydrocarbures
aromatiques volatils, en naphtalène et en hydrocarbures
halogénés volatils — Méthode par purge et piégeage avec
désorption thermique
1 Domaine d’application
La présente Norme internationale spécifie une méthode pour la détermination quantitative par
chromatographie en phase gazeuse des hydrocarbures aromatiques volatils, du naphtalène et des
hydrocarbures halogénés volatils contenus dans les sols.
La présente Norme internationale est applicable à tous les types de sols.
NOTE En cas de sols tourbeux insaturés, une absorption de la solution d’extraction peut avoir lieu.
La limite inférieure de détermination quantitative dépend du matériel utilisé et de la qualité du
méthanol utilisé pour l’extraction de l’échantillon de sol.
Dans les conditions spécifiées dans la présente Norme internationale, les limites de détermination
quantitative suivantes (exprimées par rapport à la matière sèche) s’appliquent:
Limite de détermination quantitative type lorsque le couplage CG-FID est utilisé:
Hydrocarbures aromatiques volatils: 0,1 mg/kg
Limite de détermination quantitative type lorsque le couplage CG-ECD est utilisé:
Hydrocarbures halogénés volatils: 0,0
...


NORME ISO
INTERNATIONALE 15009
Troisième édition
2016-02-15
Qualité du sol — Détermination par
chromatographie en phase gazeuse
des teneurs en hydrocarbures
aromatiques volatils, en naphtalène et
en hydrocarbures halogénés volatils
— Méthode par purge et piégeage avec
désorption thermique
Soil quality — Gas chromatographic determination of the content
of volatile aromatic hydrocarbons, naphthalene and volatile
halogenated hydrocarbons — Purge-and-trap method with thermal
desorption
Numéro de référence
©
ISO 2016
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – Tous droits réservés

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Principe . 2
4 Réactifs . 2
4.1 Eau, exempte d’hydrocarbures aromatiques volatils et d’hydrocarbures
halogénés volatils . 2
4.2 Étalons internes . 3
4.3 Composés étalons . 3
4.3.1 Hydrocarbures aromatiques volatils . 3
4.3.2 Hydrocarbures halogénés volatils . 4
4.4 Méthanol . 4
4.5 Agent d’adsorption . 4
4.6 Eau de refroidissement, pour la purge et le piégeage . 5
4.7 Gaz inerte, pour le chromatographe en phase gazeuse . 5
4.8 Azote ou hélium, utilisé comme gaz inerte pour le dispositif de purge . 5
4.9 Solutions étalons . 5
4.9.1 Solutions étalons mères, pour composés aromatiques et halogénés
volatils dans du méthanol, 4 g/l . 5
4.9.2 Solutions étalons internes dans du méthanol, 4 g/l . 5
4.9.3 Solutions d’étalonnage . 5
4.10 Méthanol contenant des étalons internes . 6
5 Appareillage . 6
6 Échantillonnage, conservation et traitement préliminaire des échantillons .8
6.1 Généralités . 8
6.2 Échantillonnage par la méthode de flacons préremplis de méthanol . 8
6.3 Échantillonnage par la méthode du tube de carottage. 8
7 Mode opératoire. 9
7.1 Détermination à blanc . 9
7.2 Extraction . 9
7.3 Purge et piégeage . 9
7.4 Analyse par chromatographie en phase gazeuse .10
7.4.1 Conditions d’analyse par chromatographie en phase gazeuse .10
7.4.2 Étalonnage .11
7.4.3 Mesurage .12
8 Calcul .12
8.1 Calcul de la concentration d’un composé volatil dans un échantillon d’eau .12
8.2 Calcul de la concentration d’un composé volatil dans l’échantillon de sol .13
9 Expression des résultats.13
10 Fidélité .14
11 Rapport d’essai .14
Annexe A (informative) Temps de rétention relatifs par rapport à l’éthylbenzène-D10 des
hydrocarbures aromatiques volatils et des hydrocarbures halogénés volatils sur les
colonnes suivantes: CP-Sil 5 CB et CP-Sil 13 CB .15
Annexe B (normative) Vérification des étalons internes .17
Annexe C (informative) Validation .18
Annexe D (informative) Informations sur les instruments de purge et de piégeage .21
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO, participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à
l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes
de l’OMC concernant les obstacles techniques au commerce (OTC), voir le lien suivant: Avant-propos -
Informations supplémentaires
Le comité chargé de l’élaboration du présent document est l’ISO/TC 190, Qualité du sol, sous-comité SC 3,
Méthodes chimiques et caractéristiques du sol.
Cette troisième édition annule et remplace la deuxième édition (ISO 15009:2012), qui a fait l’objet d’une
révision technique.
iv © ISO 2016 – Tous droits réservés

NORME INTERNATIONALE ISO 15009:2016(F)
Qualité du sol — Détermination par chromatographie en
phase gazeuse des teneurs en hydrocarbures aromatiques
volatils, en naphtalène et en hydrocarbures halogénés
volatils — Méthode par purge et piégeage avec désorption
thermique
1 Domaine d’application
La présente Norme internationale spécifie une méthode pour la détermination quantitative par
chromatographie en phase gazeuse des hydrocarbures aromatiques volatils, du naphtalène et des
hydrocarbures halogénés volatils contenus dans les sols.
La présente Norme internationale est applicable à tous les types de sols.
NOTE En cas de sols tourbeux insaturés, une absorption de la solution d’extraction peut avoir lieu.
La limite inférieure de détermination quantitative dépend du matériel utilisé et de la qualité du
méthanol utilisé pour l’extraction de l’échantillon de sol.
Dans les conditions spécifiées dans la présente Norme internationale, les limites de détermination
quantitative suivantes (exprimées par rapport à la matière sèche) s’appliquent:
Limite de détermination quantitative type lorsque le couplage CG-FID est utilisé:
— Hydrocarbures aromatiques volatils: 0,1 mg/kg
Limite de détermination quantitative type lorsque le couplage CG-ECD est utilisé:
— Hydrocarbures halogénés volatils: 0,01 mg/kg
Des limites de détermination quantitative plus faibles peuvent être atteintes pour certains composés si
l’on utilise la spectrométrie de masse (SM) avec détection sélective des ions.
2 Références normatives
Les documents ci-après, dans leur intégralité ou non, sont des références normatives indispensables à
l’application du présent document. Pour les références datées, seule l’édition citée s’applique. Pour les
références non datées, la dernière édition du document de référence s’applique (y compris les éventuels
amendements).
ISO 4799, Verrerie de laboratoire — Réfrigérants
ISO 10381-1, Qualité du sol — Échantillonnage — Partie 1: Lignes directrices pour l’établissement des
programmes d’échantillonnage
ISO 10381-2, Qualité du sol — Échantillonnage — Partie 2: Lignes directrices pour les techniques
d’échantillonnage
ISO 10381-5, Qualité du sol — Échantillonnage — Partie 5: Lignes directrices pour la procédure
d’investigation des sols pollués en sites urbains et industriels
ISO 11465, Qualité du sol — Détermination de la teneur pondérale en matière sèche et en eau — Méthode
gravimétrique
ISO 15680, Qualité de l’eau — Dosage par chromatographie en phase gazeuse d’un certain nombre
d’hydrocarbures aromatiques monocycliques, du naphtalène et de divers composés chlorés par dégazage,
piégeage et désorption thermique
I
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.