ISO 8301:1991/Amd 1:2010

General Information

Publication Date
Current Stage
6060 - International Standard published
Start Date
Completion Date
Ref Project


Buy Standard

ISO 8301:1991/Amd 1:2010
English language
3 pages
sale 15% off
sale 15% off

Standards Content (sample)

First edition
Thermal insulation — Determination of
steady-state thermal resistance and
related properties — Heat flow meter
Isolation thermique — Détermination de la résistance thermique et des
propriétés connexes en régime stationnaire — Méthode fluxmétrique
Reference number
ISO 8301:1991/Amd.1:2010(E)
ISO 2010
---------------------- Page: 1 ----------------------
ISO 8301:1991/Amd.1:2010(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

© ISO 2010

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 8301:1991/Amd.1:2010(E)

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

Amendment 1 to ISO 8301:1991 was prepared by Technical Committee ISO/TC 163, Thermal performance

and energy use in the built environment, Subcommittee SC 1, Test and measurement methods.

© ISO 2010 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 8301:1991/Amd.1:2010(E)
Thermal insulation — Determination of steady-state thermal
resistance and related properties — Heat flow meter apparatus
Page 1, 1.2
Delete footnote 1.
Page 5,
Add the following note at the end of the subclause:

NOTE Comparative tests under the European Key Mark scheme have shown that it is possible to


Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.